20MnCr5圆棒锯切困难原因分析

某厂在锯切20MnCr5圆棒过程中锯条容易断裂，采用光学显微镜(OM)和扫描电子显微镜(SEM)等观察分析手段，对锯条容易断裂的原因进行分析。分析结果表明：锯条断裂的原因为加工20MnCr5过程中粘刀崩齿。针对此类加工缺陷，提出了相应的改进措施。     

物料堆场智能化管理经验分享

华润水泥（罗定）有限公司根据物料储存需求，共有三个长堆棚分为9个室内料场堆放原材料及混合材，厂内有4台铲车无规则轮流在这8个料场内作业，同时外来运料货车、公司化验及验收人员也会不间断地进入不同堆棚。由于料场内空间狭窄，驾驶员视线不好，如果堆棚料场内铲车在作业时，有其他人员或车辆进入铲车工作区域共同作业，在没有检测装置对进入的人、车进行识别，提醒铲车驾驶员的情况下，容易发生碾压进入人员或车辆碰撞的安全事故。公司根据现场实际，自2020年起决定实施从堆场出入口智能红外感应技术、装载机车载识别系统、智能声光语音提醒、实时监控显示、照明、堆场硬件设施等五方面实施物料堆场车辆智能化安全预警系统项目。     

0CrMnTiH齿轮钢的淬透性计算及窄淬透性带控制

采用非线性方程计算法计算20CrMnTiH钢末端淬透性,只需利用生产实际数据加以修正,就能进行精确的淬透性计算和预报,与实测值偏差不超过2HRC。采用化学成分设计和控制,保证20CrMnTiH钢△[C]不超过0.007%,△[Si]波动不超过0.04%,△[Mn]、△[Cr]不超过0.02%,△[Ti]不超过0.01%,△[Alt]不超过0.010%,[Ni]、[Cu]不超过0.05%,[Mo]、[W]、[V]不超过0.03%,[P]、[S]不超过0.020%,[N]和[B]分别不超过0.006 0%和0.0005%,并控制碳偏析指数不超过1.035%,可实现国际先进水平的末端淬透性HRC4带宽控制。     

基于光谱分类模型的保险杠物证无损研究

采用中红外光谱结合化学计量学的方法对车用保险杠碎片进行鉴别，分别对52个车用保险杠碎片样本的全波段光谱数据、指纹区光谱数据和主成分分析降维后的光谱数据建立Fisher判别分析和K近邻算法2种分类模型，并对分类结果进行比较。结果表明，主成分分析提取特征变量后构建的分类模型，分类的准确率更高，对聚丙烯（PP）、PP/滑石粉、PP/滑石粉/碳酸钙（CaCO₃）3种类型的样本分类准确率达到92.3 %，对PP/滑石粉类型中的10种品牌样本分类准确率达到88.9 %，分类结果理想；在构建的2种分类模型中，Fisher判别分析模型的分类率远高于K近邻算法模型，分析认为K近邻算法模型受到样本不均衡的影响；中红外光谱结合化学计量学可以实现对车用保险杠碎片的准确区分，且满足快速、无损的检验要求。     

A computer aided design method for car form and its application based on shape parameters

In the early design stage, automotive modeling should both meet the requirements of aesthetics and engineering. Therefore, a vehicle CAD (computer aided design) model that can be easily adjusted by feedbacks is necessary. Based on CE-Bézier surface, this paper presents a set of algorithms for parametric segmentation and fairing surface generation in a car model. This model is defined by a simplified automotive template and relevant control points, shape parameters and segmentation parameters, which can be modified to alter the car form efficiently. With this model and the corresponding adjustment method, more than fifty various vehicle models are established in this research according to different parameters. And two methods for calculating similarity index between car models are constructed, which are suitable for brand design trend analysis and modelling design decisionmaking.     

LLM-105/CL-20基高能钝感PBX的制备与性能表征

为满足含能材料高能钝感的要求,以CL-20为主体炸药,LLM-105为钝感剂,采用溶液水悬浮法制备了LLM-105质量分数分别为10%、20%、30%的3种LLM-105/CL-20基PBX。通过扫描电子显微镜(SEM)、粉末X射线衍射仪(PXRD)和差示扫描量热仪(DSC)对样品的形貌、晶体结构和热性能进行表征,并测试其机械感度;采用EXPLO5软件计算了其爆轰参数。结果表明,LLM-105/CL-20基PBX样品呈类球形,颗粒密实,粒径约为500μm;PBX中各组分的晶体结构未发生改变;3种配方的热安定性都较好,且随着钝感剂LLM-105含量的增加,LLM-105/CL-20基PBX的热爆炸临界温度呈递增趋势;与原料CL-20相比,3种LLM-105/CL-20基PBX的特性落高分别提高了25.88、33.68、37.18 cm,摩擦爆炸概率分别下降29%、38%、45%;LLM-105质量分数为10%的LLM-105/CL-20基PBX的特性落高与PBX-9501相当,而LLM-105质量分数为20%和30%的LLM-105/CL-20基PBX分别比PBX-9501高16.6%和25.12%;理论爆速分别高381.76、279.2、82.03 m/s。3种配方LLM-105/CL-20基PBX炸药的爆轰性能明显优于PBX-9501。     

Formation mechanism and microstructure evolution of Ba2Ti9O20 ceramics by reaction sintering method

Ba₂Ti₉O₂₀ single-phase ceramics were prepared by reaction sintering method using TiO₂ and BaCO₃ as raw materials after heat treating at 1150°C for 10 hours. Furthermore, the formation mechanism and microstructure evolution of Ba₂Ti₉O₂₀ ceramics prepared by reaction sintering method were investigated. The formation behavior of Ba₂Ti₉O₂₀ phase was analyzed from the perspective of diffusion, where the reaction activation energy required for the process was calculated to be about 386.17 kJ/mol. Combined with the scanning electron microscopy and the energy dispersive spectrometer, it was revealed that the pores on Ba₂Ti₉O₂₀ grains in the process of reaction sintering might be caused by the absence of oxygen element. Meanwhile, the reason for the roughness of ceramic surface was that the local inhomogeneous distribution of barium on the surface of Ba₂Ti₉O₂₀ grain leaded to the enrichment of titanium.