Microstructure and mechanical behavior of laser aided additive manufactured low carbon interstitial Fe49.5Mn30Co10Cr10C0.5 multicomponent alloy

Laser aided additive manufacturing(LAAM)was used to fabricate bulk Fe49.5Mn30Co10Cr10C0.5 interstitial multicomponent alloy using pre-alloyed powder.The room temperature yield strength(σy),ultimate tensile strength(σUTS)and elongation(εUST)were 645 MPa,917 MPa and 27.0％respectively.The as-built sample consisted of equiaxed and dendritic cellular structures formed by elemental segregation.These cellular structures together with oxide particle inclusions were deemed to strengthen the material.The other contributing components include dislocation strengthening,friction stress and grain bound-ary strengthening.The high εUTS was attributed to dislocation motion and activation of both twinning and transformation-induced plasticity(TWIP and TRIP).Tensile tests performed at-40℃and-130℃demonstrated superior tensile strength of 1041 MPa and 1267 MPa respectively.However,almost no twinning was observed in the fractured sample tested at-40℃and-130℃.Instead,higher fraction of strain-induced hexagonal close-packed(HCP)ε phase transformation of 21.2％were observed for fractured sample tested at-40℃,compared with 6.3％in fractured room temperature sample.     

Flash Lamps as Ignition and Initiation Sources of the VS-2 Pyrotechnic Composition

In the present work it is found that the pyrotechnic composition VS-2 can be initiated with flash lamps IFC-500 and EVIS. VS-2 pyrotechnic composition contains 90% of mercury（Ⅱ） 5-hydrazinotetrazolate perchlorate and 10% of optically transparent copolymer of 2-methyl-5-vinyltetrazole and methacrylic acid （PVMT）. We have found that the flash lamps make it possible to initiate combustion of VS-2 composition with its transition to detonation both in cylindrical charges placed in brass caps of 5 mm diameter and 2 mm high， and film charges with 10 mm×80 mm in size and surface weights of 60 mg·cm^-2 and 90 mg·cm^-2， showing ignition delay times 10 μs and 3 μs， respectively. We also measured detonation velocities for VS-2 composition film charges， which were 4375-4505 m·s^-1 （of the charge being surface mass 60 mg·cm^-2） and 4221-4281 m·s^-1 （of the charge being surface mass 90 mg·cm^-2） and their blasting action on the aluminum plate. The depths of the normal shock wave imprints at the charge-barrier interface were 0.6-0.7 mm （for surface mass of the film charges 60 mg·cm^-2） and 1.2-1.3 mm （for surface mass of the film charges 90 mg·cm^-2）.     

关于COVID-19、膜脂质与公众健康（网络首发、推荐阅读）

冠状病毒具有一层脂质膜。虽然复制需要劫持宿主的RNA工具来合成病毒体蛋白，但必须将其包裹在脂质膜中，促其萌生以扩展感染。最近研究表明，某些必需脂肪酸可以抑制其复制活性。脂质膜通常被认为是水溶物的脂肪屏障，但它对细胞和亚细胞的功能是高度有序和组分特异性的，其对病毒外壳可能也有最佳的特异性。虽然复制中DNA、RNA和蛋白质组成不受饮食影响，但脂质膜受其影响。此外，自1960年代以来，人们就知道男性对这些必需脂肪酸和膜完整性不足的敏感性高于女性。有证据表明，花生四烯酸和二十二碳六烯酸具有抗病毒、免疫、抗炎、控制血压和消退素活性，因此，迫切需要考察它们在Covid-19预防和治疗中的地位，也需重新评估现行的膳食指导。当前，有关脑、神经、血管和免疫系统等富含膜系统对脂质需求还尚未被详细认识。毫无疑问，这些脂质在几百万年来塑造人类基因组方面具有重要意义，因此，如果这些膜脂质失衡将会使人类面临机体紊乱和感染风险，且男性比女性风险更大。     

Fe3O4-carbon spheres core–shell supported palladium nanoparticles: A robust and recyclable catalyst for suzuki coupling reaction

Suzuki-Miyaura (S-M) is regarded the most powerful way for synthesis biaryls, triaryls, or incorporating of substituted aryl moieties in organic preparation by the cross-coupling of aryl boronic acid with aryl halides using the Pd catalyst. This work reports the combining of the hydrothermal and microwave-assisted protocol to convert the glucose to magnetic carbon spheres (Fe₃O₄-CSPs) decorated with Pd nanoparticles (NPs) as the catalyst for Suzuki-Miyaura cross-coupling reactions. The physicochemical properties in the produced composite were examined using FESEM, HRTEM, nitrogen isotherms, Raman spectroscopy, FTIR, XPS, and XRD. The as-fabricated composite Pd/Fe₃O₄-CSPs is mostly spherical with a core–shell structure and possesses a great surface area of 253.2 m²·g^-1. Its catalytic performance demonstrates that the composite has excellent stability and high tolerance Suzuki-Miyaura cross-coupling reactions in 30 min at 80 ℃. Both activated and deactivated aryl halides provided excellent yield. The as-fabricated catalyst was recycled for up to four catalytic cycles without a substantial decline in performance. Moreover, this research offers a facile roadmap for synthesizing Pd/Fe₃O₄-CSPs composites and promoting the practical implementation of Pd/Fe₃O₄-CSPs catalysts for organic transformation processes.     

Advances in reduction of NOx and N2O1 emission formation in an oxy-fired fluidized bed boiler

Fossil fuel combustion is one of the major means to meet the mounting global energy demand. However, the increasing NO_x and N₂O emissions arising from fossil fuel combustion process have hazardous effects. Thus, mitigating these gases is vital to attain a sustainable environment. Interestingly, oxy-fuel combustion in fluidized bed for carbon capture and minimized NO_x emissions is strongly sustainable compare to the other approaches. It was assessed that NO_x formation and fuel-N conversion have significant limitation under oxy-fluidized bed compared to air mode and the mechanism of NO_x formation is still deficient and requires further development. In addition, this review paper discussed the potential of primary measure as low emission process with others supplementary techniques for feasible NO_x reduction. The influences of combustion mode, operating parameters, and reduction techniques such as flue gas recirculation, oxygen staging, biomass co-firing, catalyst, influence of fluidized bed design and structure, decoupling combustion and their merges are respectively evaluated. Findings show that significant minimization of NO_x emission can be achieved through combination of primary and secondary reduction techniques.     

Electron transfer mediator PCN secreted by aerobic marine Pseudomonas aeruginosa accelerates microbiologically influenced corrosion of TC4 titanium alloy

Titanium alloys possess excellent corrosion resistance in marine environments,thus the possibility of their corrosion caused by marine microorganisms is neglected.In this work,microbiologically influenced corrosion (MIC) of TC4 titanium alloy caused by marine Pseudomonas aeruginosa was investigated through electrochemical and surface characterizations during a 14-day immersion test.Results revealed that the unstable surface caused by P.aeruginosa resulted in exposure of Ti2O3 and severe pitting corrosion with maximum pit depth of 5.7 μm after 14 days of incubation.Phenazine-1-carboxy[ate (PCN),secreted by P.aeruginosa,promoted extracellular electron transfer (EET) and accelerated corrosion.Deletion of the phzH gene,which codes for the enzyme that catalyzes PCN production,from the P.aeruginosa genome,resulted in significantly decreased rates of corrosion.These results demonstrate that TC4 titanium alloy is not immune to marine MIC,and EET contributes to the corrosion of TC4 titanium alloy caused by P.aeruginosa.     

Covalent triazine framework with efficient photocatalytic activity in aqueous and solid media

Covalent triazine frameworks (CTFs) have been recently employed for visible light-driven photocatalysis due to their unique optical and electronic properties. However, the usually highly hydrophobic nature of CTFs, which originates from their overall aromatic backbone, leads to limitations of CTFs for applications in aqueous media. In this study, we aim to extend the range of the application media of CTFs and design hybrid material of a CTF and mesoporous silica (SBA-15) for efficient photocatalysis in aqueous medium. A thiophene-containing CTF was directly synthesized in mesopores of SBA-15. Due to the high surface area and the added hydrophilic properties by silica, the hybrid material demonstrated excellent adsorption of organic molecules in water. This leads not only to high photocatalytic performance of the hybrid material for the degradation of organic dyes in water, but also for efficient photocatalysis in solvent-free and solid state. Furthermore, the reusability, stability and easy recovery of the hybrid material offers promising metal-free heterogeneous photocatalyst for broader applications in different reaction media.     

以金属氧化物为原料改进燃烧法合成γ-LiAlO_2（英文）

提出一种合成γ-LiAlO_2的替代解决方案—改进燃烧法直接合成γ-LiAlO_2,并将其用于相对简单的反应体系中,原料为非氧化性化合物如Al_2O_3和LiOH,燃料为尿素。采用1:1、1.5:1和2:1的非化学计量Li/Al摩尔比,在900和1000°C下反应5 min,制备LiAlO_2,并对其组织和结构进行表征。考察Li/Al摩尔比对材料形貌和高γ射线辐照下材料稳定性的影响。结果表明,所得粉体的晶体结构为?-LiAlO_2和?-LiAlO_2,其取决于Li/Al摩尔比。因此,用该方法可以成功合成微砖状、多面体状和层状?-LiAlO_2,而无需任何后续处理。γ辐照结果表明,所得到的?-LiAlO_2不分解,只形成少量的Li_2CO_3;由此可以确定,辐照会导致固结,不利于氚的有效提取;结果证明,用燃烧法生产高纯度?-LiAlO_2不需要硝酸盐前驱体。     

大型水电工程前期准备延期的影响类型分析

讨论了成本考虑不足与水电工程项目施工前准备阶段延期的负面影响,以及发展中国家不能及时有效地交付项目与稀有资源浪费间的冲突。建议项目员工、开发商、政府官员和国际金融机构重视延期成本,找到成本与效益的平衡点。