Quantitative UPLC‐MS/MS analysis of chlorogenic acid derivatives in antioxidant fractionates from dandelion (Taraxacum officinale) root

While qualitative studies have identified chlorogenic acids in antioxidant extracts, particularly ethyl acetate‐derived extracts, of Taraxacum officinale, quantitative analysis of these phenolic compounds remains largely unreported for this species. In this study, bioactivity‐guided fractionation of an antioxidant crude ethyl acetate extract (DPPH = 295.481 ± 0.955 mg TE g^?1 extract) from T. officinale root resulted in a number of reverse‐phase fractions that demonstrated high antioxidant activity (DPPH = 1058.733–1312.136 mg TE g^?1 extract), stronger than that of the synthetic antioxidant Trolox^®. UPLC‐MS/MS screening of these fractions for the presence of selected mono‐ and di‐caffeoylquinic acids revealed large quantities of 1,5‐dicaffeoylquinic acid present in several fractions (853.052–907.324 μg mg^?1), respectively. Due to the antioxidant potency and high levels of 1,5‐dicaffeoylquinic acid observed in these fractions, it was concluded that specifically this chlorogenic acid derivative is a major contributor to the antioxidant efficacy of dandelion root.     

Ni-P/HZSM-5催化木质素降解制备酚类化学品

采用Ni-P复合改性HZSM-5催化剂催化木质素降解制备高附加值的单酚类化学品，探讨了催化剂种类、金属负载量、反应温度、反应时间以及溶剂种类对木质素催化降解制备酚类化合物的影响。同时采用X射线衍射仪（XRD）、比表面积和孔径分析仪（BET）、化学吸附仪（NH₃-TPD）、热重分析仪（TG）以及气相色谱质谱联用仪（GC/MS）对催化剂以及液相产物进行分析表征，同时探讨其催化失活以及再生机制。结果表明：Ni、P高度分散在HZSM-5催化剂的表面，Ni的添加有效地弱化了C－C键，致使β-O-4和α-O-4发生断裂，有效地提高了木质素加氢解聚的活性，减少了焦炭的生成，但催化剂的再生水热稳定性较差，重复使用性较低。当采用甲醇为供氢试剂，在反应温度为220℃，氢气压力为2MPa，反应时间为8h，催化剂负载量为10%，NaOH为共催化剂时，其木质素的转化率为98.6%，酚类化合物的含量达到74.97%。产物以苯酚、愈创木酚和紫丁香酚为主，低温促进了紫丁香酚的产生。     

诺氟沙星片在中国健康受试者空腹和餐后状态下生物等效性研究#br#

目的：采用随机、开放、两周期、自身交叉、单次给药试验设计比较浙江医药股份有限公司新昌制药厂生产的诺氟沙星片与原研产品BACCIDAL在中国健康人体中的生物利用度，并评价两种制剂的生物等效性。方法：分别在空腹和餐后条件下，健康受试者随机交叉单剂量口服诺氟沙星片受试制剂或参比制剂100 mg，采用液相色谱-质谱串联（LC-MS/MS）法测定受试者服药前后不同时间点血浆内药物浓度，采用WinNonlin 7.0软件计算主要药代动力学参数，并评价两种制剂的生物等效性。结果：空腹试验共有28例受试者入组并完成试验，诺氟沙星受试制剂与参比制剂的Cmax分别为（607.62±125.24）ng/mL和（552.01±134.11）ng/mL；AUC0-t分别为（2 551.66±509.08）ng·mL-1·h和（2 429.98±460.47）ng·mL-1·h；AUC0-∞分别为（2 675.40±523.04）ng·mL-1·h和（2 557.68±485.43）ng·mL-1·h；t1/2分别为（6.07±0.69）h和（6.18±0.92）h；两种制剂的Cmax、AUC0-t和AUC0-∞几何均值比的90%置信区间分别为101.45%～121.94%、98.96%～111.27%、98.82%～110.76%。餐后试验共有28例受试者入组并完成试验，诺氟沙星受试制剂与参比制剂的Cmax分别为：（256.54±58.87）ng/mL和（300.80±94.67）ng/mL；AUC0-t分别为（1 314.74±349.92）ng·mL-1·h和（1 278.60±314.77）ng·mL-1·h；AUC0-∞分别为（1 413.73±361.98）ng·mL-1·h和（1 374.98±321.62）ng·mL-1·h；t1/2分别为（6.66±1.23）h和（6.66±1.34）h；两种制剂的Cmax、AUC0-t和AUC0-∞几何均值比的90%置信区间分别为81.42%～93.56%、99.61%～105.58%、99.80%～105.21%。结论：浙江医药股份有限公司新昌制药厂生产的诺氟沙星片与原研产品BACCIDAL在中国健康受试者空腹和餐后服用的状态下等效且安全性良好，临床上可以替换使用。     

Fabrication of novel silicon carbide-based nanomaterials with unique hydrophobicity and microwave absorption property

Novel SiC-based nanomaterials, namely the nitrogen and aluminum co-doped SiC@SiO₂ core-shell nanowires and nitrogen-doped SiO₂/Al₂O₃ nanoparticles, have been fabricated through a facile thermal treatment process based on the chemical vapor deposition and vapor-liquid reaction. These nanomaterials show remarkable hydrophobicity with a water contact angle (CA) over 140°, which are aroused by the surface zigzag morphology of the nanostructures and the hydrocarbyl groups generated during the preparation process. Moreover the nanocomposites also exhibit relatively prominent microwave absorption (MA) properties in the frequency range of 2.0-18.0 GHz. The minimum reflection loss (RL) value as low as −23.68 dB can be observed at 14.16 GHz when the absorber thickness is 2.6 mm with a loading rate of 16.7 wt%. And the nanocomposites-based absorbent can achieve an effective absorption bandwidth (RL < −10 dB) of 4.48 GHz with the absorbent thickness of 2.5 mm. This enhanced microwave attenuation performance can be attributed to multiple polarizations and perfect impedance matching conditions, as well as multiple internal reflections. These marvelous properties make these N and Al co-doped SiC@SiO₂ core-shell nanowires and N-doped SiO₂/Al₂O₃ nanoparticles display extensive application potential as MA materials in harsh environment.     

伞帽用高铬铸铁在热强碱腐蚀环境下的磨损分析

针对氧化铝行业中常用的Cr28和Cr20高铬铸铁伞帽在相同工况条件下的磨损机理进行分析,并对比研究了实际生产中两种失效材料的成分、组织及性能。结果表明,伞帽部件在高温强碱腐蚀条件下受到外界冲刷时,磨损量由微切削磨损与变形磨损这两种机制共同决定。含铬量较高的Cr28高铬铸铁,其冲刷和抗腐蚀磨损性能均优于Cr20高铬铸铁。伞帽服役寿命主要受浆料和表层的铸铁材料两大因素影响。两种试验材料经淬火+回火处理后,基体组织中主要为回火马氏体+M₇C₃型碳化物+少量残留奥氏体,其中含铬量较高的Cr28高铬铸铁中共晶碳化物含量更高,且分布更加弥散,其平均硬度值为64.0 HRC,高于Cr20高铬铸铁的60.2 HRC。最终确定Cr28高铬铸铁作为伞帽材质更能满足氧化铝生产及设备检修周期的需要。     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

Super-oleophilicity Co-doping Co2+/F-/TiO2 one-dimensional nanotubes for photocatalytic denitrification of light oil

In this study, a simple hydrothermal synthesis method was adapted for the preparation of Co-doping Co²⁺/F^-/TiO₂ nanotubes photocatalyst, and the micro-nano structure of catalysts prepared by biomimetic technology which makes the catalyst have super-oleophilicity property. Co²⁺/F^-/TiO₂ revealed improved photocatalytic performance for denitrification of light oil compared to single TiO₂ photocatalysts. The enhance of photocatalytic activity can be attributed to narrowing the band gap, increasing the light response wavelength and exposing more highly active crystal surfaces due to synergistic effects of Co²⁺ and F^? in the photocatalyst.     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.