自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

低渗透气藏应力敏感性实验研究

地应力是影响储层物性参数的重要因素，特别是对地应力敏感的储层、、实验研究表明。不管是干燥岩石还是含束缚水岩石，低渗透砂岩气藏储层的应力敏感性是客观存在的。而且这种应力敏感性对储层渗透率造成的伤害不可忽视。随着有效压力的升高，渗透率是逐渐降低的低渗透气藏岩心的孔隙度随有效压力的增大呈指数关系递减。低渗透气藏应力敏感性与储层含水饱和度有关，束缚水饱和度越高。应力敏感性越强。低渗透气藏孔隙变形具有弹塑性变形的特征。     

镜质体反射率与砂岩孔隙度关系的研究与应用

利用有关孔隙度和有机质热成熟度的理论公式研究了二者之间的内在联系 ,建立起Ro与砂岩孔隙度之间的关系模型。用该模型对济阳坳陷沾化凹陷渤南洼陷沙河街组四段上亚段烃源层有机质的成熟度进行了估算 ,指出该烃源层有机质已达到成熟     

用CT技术确定砂岩的孔隙度

周渤然等．用ＣＴ技术确定砂岩的孔隙度．测井技术，１９９４，１８（３）：１７８～１８４本文首先提出用计算机层析（ＣＴ）技术确定砂岩孔隙度的原理和方法。通过对四块人工岩样和六十块砂岩岩样的测定，其结果表明该方法是可靠的。使用ＣＴ技术可定量、定性地解释某些岩样的内部特征，重矿物分布及裂缝变化情况。实践表明，采用图象减法技术则有助于消除光束硬化现象造成的误差。     

An investigation of pore cracking in titanium welds

Two welded Ti-6A1-4V pressure vessels leaked prematurely in service. The leaks were caused by cracks emanating from weld porosity. The cracks originated during fabrication, with subsequent growth in service leading to the formation of the leak paths. Pore cracking is thought to be caused by a mechanism that involves both sustained-load and cyclic contributions, with the former being the more prominent. It is shown that the tendency for cracking is influenced by pore position and that pore size is not a deciding factor in that regard. The factors that govern pore cracking are discussed, and the possible role of interstitial embrittlement is assessed.     

不同压力下气层岩样m、n值变化的实验研究

胶结指数m和饱和度指数n变化规律的研究一直是岩石物理学家和测井解释分析家关注的问题。压力是影响m、n的重要因素,但迄今为止,仍未取得可使多数人接受的一般性结论。实验开展了低孔隙度低渗透率气层岩样在不同压力条件下的电阻率测量,在考虑孔隙度随压力变化的基础上建立了m、n参数随压力变化的关系,得出结论:某些地区的气层岩样在压力增大时即使考虑孔隙度变化,m值增大,n值减小。     

Cyclic variations in the permeability of the cell wall of Saccharomyces cerevisiae.

To study cell-cycle-related variations in wall permeability of Saccharomyces cerevisiae, two approaches were used. First, an asynchronous culture was fractionated by centrifugal elutriation into subpopulations containing cells of increasing size. The subpopulations represented different stages of the cell cycle as judged by light microscopy. Cell wall porosity increased when these subpopulations became enriched with budded cells. Secondly, synchronous cultures were obtained by releasing MATa cells from alpha-factor induced G1-arrest. These cultures grew synchronously for at least two generations. The cell wall porosity increased sharply in these cultures, shortly before buds became visible and was maximal during the initial stages of bud growth. It decreased in cells which had completed nuclear migration and before abscission of the bud had occurred. The porosity reached its lowest value during abscission and in unbudded cells. We examined the incorporation of mannoproteins into the wall during the cell cycle. SDS-extractable mannoproteins were incorporated continuously. However, the incorporation of glucanase-extractable mannoproteins, which are known to affect cell wall porosity, showed cyclic oscillations and reached its maximum after nuclear migration. This coincided with a rapid decrease in cell wall porosity, indicating that glucanase-extractable mannoproteins might contribute to this decrease.     

铜基催化剂孔隙率对气体有效扩散系数的影响

研究了18种具有不同孔结构参数的粒状铜基甲醇合成催化剂孔隙率对有效扩散系数的影响。结果发现，催化剂微孔孔隙率增大，曲节因子亦增大，扩散阻力增加。将孔隙率与催化剂曲节因子关联，得到了半经验方程，用它可估算催化剂的曲节因子。     

Effect of Dilution and Porosity on Self-Propagating High-Temperature Synthesis of Silicon Nitride

Self-propagating high-temperature synthesis is a very easy and low-cost method to synthesize Si₃N₄. The nitriding of silicon powder takes place in a self-sustained regime under high pressures of nitrogen with dilution of silicon by Si₃N₄. In this work effects of dilution and green-mixture porosity on combustion velocity and phase content of reaction products are studied. Results are compared with previous work of other authors and different behaviors are found. An explanation of these behaviors is given.