The effects of the modification of the BST-system solid solutions with rare earth elements

The conditions for the preparation of the solid solutions of a binary system of barium-strontium titanates with the substitutions in the A-sublattice with the rare-earth elements (REE), including the solid-phase synthesis, mechanical activation and sintering of dispersed-crystalline products by the conventional ceramic technology, were optimized. The presence (absence) of the impurity phases was established depending on the size effect of the REE. The precision X-ray diffraction analysis revealed the features of the phase formation in the studied solid solutions and showed that the “behavior” of the structural characteristics of the solid solutions with the participation of the REE is determined by the limiting conditions of the isomorphism and anion excess of the media under study. An assumption is made about the nature of the formation of a fine-grained landscape of the modified solid solutions, associated with the multicluster structure of the crystallite structure and the formation of the ballast phases during their synthesis. The dependences of the dielectric properties of the solid-state solution on the external influences – temperature, frequency of an alternating electric field and strength of a constant field – have been established. The possibility of choosing on the basis of the obtained data, promising for practical applications of the compositions is shown.     

Effect of ball-milling parameters on the rheological properties of mold powder slurry

In this study, mold powder slurries with high solid loading and low viscosity were prepared during the ball-milling process for improving the homogeneity and mechanical properties of granules after spray-drying. The effect of ball-milling parameters, such as solid loading, binder/dispersant content, and ball-milling time, on the flowability, dispersibility, stability, and rheological behavior of mold powder slurries was systematically investigated by rheology observation and sedimentation tests. As these parameters varied, the slurry exhibited the shear-thinning behavior of a non-Newtonian fluid with a shear rate range of 0–50 s^?1, which was adequately described by the Herschel-Bulkley model. The optimal parameters that optimized the flowability, dispersibility, and stability of the slurry, along with its rheological behavior, were chosen as follows: solid loading, 60 wt%; modified sodium carboxymethyl cellulose binder content, 1.0 wt%; sodium tripolyphosphate dispersant content, 0.5 wt%; ball-milling time, 60 min.     

Effect of polyethyleneimine-fatty acid complex type dispersant structure on the overall processing chain of Si3N4 ceramics using multicomponent non-aqueous slurries

The effect of fatty acid structure of polyethyleneimine (PEI)-fatty acid complex, which was designed as a polymer dispersant for multi-component non-aqueous slurries, on the overall processing chain of Si₃N₄ ceramics involving slurry stabilization, spray drying, compaction, and liquid sintering was investigated using PEI-oleic acid (PEI-OA) and PEI-isostearic (PEI-ISA) complexes. Si₃N₄-Y₂O₃-Al₂O₃-AlN-TiO₂/toluene slurries were selected as a real model for Si₃N₄-based multicomponent slurries. It was observed that both PEI-OA and PEI-ISA can stabilize Si₃N₄-Y₂O₃-Al₂O₃-AlN-TiO₂/toluene slurries; however, the PEI-ISA system tended to have slightly higher slurry viscosity, which was suspected to be due to the interactions between protruded PEI segments among short ISA chains. The spray-dried granules from PEI-ISA-stabilized slurry were observed to have filled structures with higher surface roughness whereas those prepared from PEI-OA-stabilized slurry were observed to have hollow-structured granules. The granules prepared from PEI-OA slurry had improved flow and compaction properties with higher relative density of green compacts compared with those prepared from PEI-ISA-stabilized slurry, whereas the relative density and microstructural homogeneity of S₃N₄ ceramics sintered at 1600?°C for 2?h were observed to be higher for the PEI-ISA system. It is suspected that PEI-OA effectively improved the dispersion stability of multicomponent slurries and flow/compaction properties of granules; however, the inhomogeneous microstructures of green compacts induced by the hollow-structured granules had an adverse effect on the sintering of Si₃N₄ ceramics.     

Effect of neodymium substitution on crystalline orientation,microstructure and electric properties of sol-gel derived PZT thin films

Pb(Nd_xZr_0.52Ti_0.48)O₃ (PNZT) (x = 0%, 1%, 2%, 3%, 4%, 5%) thin films were prepared by sol-gel process to investigate the effects of neodymium substitution on crystalline orientation, microstructure and electric properties of lead zirconate titanate (PZT) films. X-ray diffraction (XRD) and scanning electron microscope (SEM) analysis showed that PNZT films with Nd doping concentration below 3% exhibited dense perovskite structure with (100) preferred orientation. The average grain size of PNZT films decreased as the Nd substitution increased. The maximum dielectric constant, remnant polarization and minimum coercive field were obtained in 2% Nd-doped PZT films. Fatigue resistance was also improved significantly with 2% Nd dopant.     

35CrMo钢组织遗传消除工艺研究

通过对船用长轴类大锻件的热处理工艺研究得知,采用临界区高温侧正火热处理工艺可以有效消除35CrMo钢组织遗传现象,细化晶粒。     

Compressive strength and microstructure of alkali-activated fly ash/slag binders at high temperature

This paper reports the results of the compressive strength and microstructure of various alkali-activated binders at elevated temperatures of 300 and 600 °C. The binders were prepared by alkali-activated low calcium fly ash/ground granulated blast-furnace slag at ratios of 100/0, 50/50, 10/90 and 0/100 wt.%. Specimens free of loading were heated to a pre-fixed temperature by keeping the furnace temperature constant until the specimens reached a steady state. Then the specimen was loaded to failure while hot. XRD, SEM and FTIR techniques were used to investigate the microstructural changes after the thermal exposure. The fly ash-based specimen shows an increase in strength at 600 °C. On the other hand, the slag-based specimen gives the worst high-temperature performance particularly at a temperature of 300 °C as compared to ordinary Portland cement binder. This contrasting behaviour of binders is due to their different binder formulation which gives rise to various phase transformations at elevated temperatures. The effects of these transformations on the compressive strength are discussed on the basis of experimental results.     

Effect of ZnO/K2O ratio on the crystallization sequence and microstructure of lithium disilicate glass-ceramics

The effect of ZnO/K₂O (Z/K) ratio on the crystallization sequence and microstructure of lithium disilicate (Li₂Si₂O₅: LS2) glass-ceramics was carefully investigated for the SiO₂-Li₂O-K₂O-ZnO-P₂O₅ system. The Z/K ratios of precursor glasses were varied from 0 to 3.5 while the nucleating agent of P₂O₅ and glass modifiers of ZnO plus K₂O were fixed to have 1.5 and 4.5 mol% relative to LS2, respectively. For the samples prepared by two-stage heat treatments of 500 °C for 1 h and 800 °C for 2 h in air, the LS2 nucleation rate was increased with increasing the Z/K ratio due to the variation in crystallization sequence from type II (Li₂SiO₃: LS) to type I (LS + LS2) in addition to an amorphous phase separation in base glass. Consequently, with increasing the Z/K ratio, the LS2 crystalline phase within the glass matrix continuously changed from larger acicular ones to smaller equiaxed ones.     

LaMgAl11O19 synthesis using non-hydrolytic sol-gel methods

Polycrystalline LaMgAl₁₁O₁₉ (LMA) was prepared by four different non-hydrolytic sol-gel methods. From stable solutions, four powder precursors containing an amorphous and nanocrystalline phase with specific reactivity were obtained. The particle size, morphology, thermal behaviour, and phase composition of the powder precursors were studied using DLS, TEM, DSC/TG and XRD. Bulk ceramic samples containing LMA were prepared at 1200?°C for 16?h and examined in terms of phase purity and microstructure using XRD, SEM, and TEM. Raman spectroscopy of pure LMA was used to study the structure in detail. A mechanism of LMA formation and a relation between powder precursor properties and final phase composition is proposed. These findings may be useful for designing modern technologies for fabrication of LMA for optical or protective coating applications.