Electron beam irradiated HDPE/EVA/Mg(OH)2 composites for flame-retardant electric cables

The mechanical properties and flammability of high-density polyethylene (HDPE)/ethylene vinyl acetate (EVA) mixed with various amounts of magnesium hydroxide (Mg(OH)₂) as the filler in composites, irradiated with electron beam at an irradiation dose of 150 kGy, have been studied. It is found that high-energy electron beam irradiation has significant effects on the mechanical properties of the HDPE/EVA/Mg(OH)₂ composites. The tensile strength and elastic modulus increased greater than in the unirradiated ones. Meanwhile, with increasing the content of Mg(OH)₂ in the composites, the limiting oxygen index (LOI) value increased sharply. The microstructure of the caves of the unirradiated HDPE/EVA/Mg(OH)₂ composites show poor interface of composites compared with the irradiated ones, as observed in SEM micrographs.     

Utilization of pico hydro generation in domestic and commercial loads

Pico hydro is a term used to distinguish very small-scale hydropower with a maximum electrical output of five kilowatts (5 kW). It is a good technique of providing electricity to the off-grid remote and isolated regions that suffer energy deficit. Typical pico hydro generator is designed and supported by electrical converting system, batteries and safety equipment so that it can be installed at the residential water pipeline. In pico hydro generation, the environmental impact is negligible since large dams are not involved, and the schemes can be managed and maintained by the consumer. This paper is reviewing the application of hydro generation and particularly focusing on the implementation of pico hydro generation system in University Malaysia Pahang (UMP) Campus-Pekan. This system was designed and simulated using the Matalb simulink blocks. The pico hydro generator has been tested in a real application with a pelton turbine design which utilizes a high pressure of water flowing from the main tank into the faculties. The speed of the turbine and alternator depend on the pressure of the water. In this work, a 1.05 kW alternator is used to charge the battery and the DC power output from a battery is converted into 220 V, 50 Hz.     

Unsteady natural convection within a differentially heated enclosure of sinusoidal corrugated side walls

Numerically investigation of natural convection within a differentially heated modified square enclosure with sinusoidally corrugated side walls has been performed for different values of Rayleigh number. The fluid inside the enclosure considered is air and is quiescent, initially. The top and bottom surfaces are flat and considered as adiabatic. Results reveal three main stages: an initial stage, a transitory or oscillatory stage and a steady stage for the development of natural convection flow inside the corrugated cavity. The numerical scheme is based on the finite element method adapted to triangular non-uniform mesh element by a non-linear parametric solution algorithm. Investigation has been performed for the Rayleigh number, Ra ranging from 10⁵ to 10⁸ with variation of corrugation amplitude and frequency. Constant physical properties for the fluid medium have been assumed except for the density where Boussinesq’s approximation has been considered. Results have been presented in terms of the isotherms, streamlines, temperature plots, average Nusselt numbers, traveling waves and thermal boundary layer thickness plots, temperature and velocity profiles. The effects of sudden differential heating and its consequent transient behavior on fluid flow and heat transfer characteristics have been observed for the range of governing parameters. The present results show that the transient phenomena are greatly influenced by the variation of the Rayleigh number with corrugation amplitude and frequency.     

Model-Based Damage Identification in a Continuous Bridge Using Vibration Data

Damage often causes changes in the dynamic characteristics of a structure such as frequencies and mode shapes. Vibration-based damage identification techniques utilize the changes in the dynamic characteristics of a structure to determine the location and extent of damage in the structure. Such techniques are applied in this study to the Crowchild Bridge, a steel-free deck continuous bridge located in western Canada. While the numerical models of the bridge are correlated with the measured dynamic characteristics, computer simulation is used to study the identification of a number of different damage patterns, and the effects of measurement errors and incomplete mode shapes on the quality of results are evaluated. The effectiveness of some selected damage identification techniques is examined; the potential difficulties in identifying the damage are outlined; and areas of further research are suggested. A three-dimensional finite-element model and a simple two-dimensional girder model of the bridge have been constructed to study the usefulness of the selected damage identification methods. Another promising damage detection method proposed here is based on the application of neural networks that combines a vibration-based method.     

Integrating quality and maintenance decisions in a production-inventory model for deteriorating items

In typical production-inventory models of deteriorating items, deterioration of the production process has not been considered. In this paper, a model is proposed in which both the produced items and the production equipment deteriorate. When the production system deteriorates, it shifts to an out-of-control state and begins to produce a proportion of defective items, necessitating corrective maintenance action. A model is formulated to integrate several realistic aspects, including item and process deterioration, varying demand and production rates, quality, inspection, and maintenance. A heuristic solution algorithm is developed to determine the production and inspection schedules, and a numerical example is solved.     

COMPARISON OF TWO METHODS TO INCREASE TIP CLEARANCE AND ITS EFFECT ON PERFORMANCE OF TURBOCHARGER CENTRIFUGAL COMPRESSOR STAGE

Tip clearance between the blade tip and casing of a centrifugal compressor can be varied through two methods:by changing the blade height(M1)or by changing the casing diameter(M2). Numerical simulations are carried out to compare these two methods and their effect on the stage and impeller performance.The impeller and diffuser are connected through rotor stator boundary using frozen rotor approach.Overall stage performance and the flow configuration have been investigated for nine tip clearance levels from no gap to 1 mm.Impeller and diffuser performances are also pre- sented separately.It has been found that the overall and impeller performance are comparatively better for M1 below tip clearance of 0.5 mm whereas M2 is found advantageous above 0.5 mm of tip clear- ance.Both M1 and M2 show performance degradation with the increase in tip clearance.Two models have been proposed for the stage total pressure ratio and efficiency,which are found to be in agree- ment with experimental results.The impeller efficiency and the pressure ratio are found to be maxi- mum at tip clearance of 0.1 mm for both the cases however minimum diffuser effectiveness is also observed at the same clearance level.Diffuser effectiveness is found to be maximum at zero gap for both cases.As it is practically impossible to have zero gap for unshrouded impellers so it is concluded that the optimum thickness is 0.5 mm onwards for M1 and 0.5 mm for M2 in terms of diffuser effec- tiveness.Mass averaged flow parameters,entropy,blade loading diagram and relative pressure fields are presented,showing the loss production within the impeller passage with tip clearance.     

Nutritional and anti-nutritional components in Pachyrhizus erosus L. tuber

Tuber of Pachyrhizus erosus L., an underutilized crop, was analyzed to determine its proximate chemical composition, vitamin, mineral, and amino acid contents, and enzymatic activity. The anti-nutritional factors were also determined. The tuber had a high level of moisture, appreciable amounts of carbohydrate, crude fibre and protein and negligibly low amount of lipid. The total caloric value corresponded to 39 kcal/100 g. The amino acid profile was deficient compared to the [FAO/WHO (1973). Energy and Protein Requirements. Technical Report Series (Vol. 52, pp. 1–118). Switzerland, Geneva: WHO.] recommended pattern. The micro- and macro-nutrient analysis revealed the tuber to be potential source of potassium, sodium, phosphorus, calcium and magnesium. The tuber contained a significant amount of ascorbic acid. Thiamine, riboflavin, pyridoxine, niacin and folic acid were also detected. Very negligible contents of anti-nutrient components were observed. Comparison of these data to those of several other commonly consumed local tubers revealed that P. erosus tuber could be included in dietary formulae for man or monogastric animals, especially in those areas where carbohydrate is in short supply.     

Bio-Functionalized Manganese Nanoparticles Suppress Fusarium Wilt in Watermelon (Citrullus lanatus L.) by Infection Disruption,Host Defense Response Potentiation,and Soil Microbial Community Modulation

The use of nanofabricated materials is being explored for the potential in crop disease management. Chemically synthesized micronutrient nanoparticles (NPs) have been shown to reduce crop diseases; however, the potential of biogenic manganese NPs (bio-MnNPs) in disease control is unknown. Here, the potential and mechanism of bio-MnNPs in suppression of watermelon Fusarium wilt, caused by Fusarium oxysporum f. sp. niveum (Fon) are reported. Bio-MnNPs are synthesized by cell-free cultural filtrate of a waterrmelon rhizosphere bacterial strain Bacillus megaterium NOM14, and are found spherical in shape with a size range of 27.0–65.7 nm. Application of bio-MnNPs at 100 µg mL⁻¹ increases Mn content in watermelon roots/shoots and improves growth performance through enhancing multiple physiological processes, including antioxidative capacity. Bio-MnNPs at 100 µg mL⁻¹ suppress Fusarium wilt through inhibiting colonization and invasive growth of Fon in watermelon roots/stems, and inhibit Fon vegetative growth, conidiation, conidial morphology, and cellular integrity. Bio-MnNPs potentiate watermelon systemic acquired resistance by triggering the salicylic acid signaling upon Fon infection, and reshape the soil microbial community by improving fungal diversity. These findings demonstrate that bio-MnNPs suppress watermelon Fusarium wilt by multiple ex planta and in planta mechanisms, and offer a promising nano-enabled strategy for the sustainable management of crop diseases.     

Accelerating Differential Evolution Using an Adaptive Local Search

We propose a crossover-based adaptive local search (LS) operation for enhancing the performance of standard differential evolution (DE) algorithm. Incorporating LS heuristics is often very useful in designing an effective evolutionary algorithm for global optimization. However, determining a single LS length that can serve for a wide range of problems is a critical issue. We present a LS technique to solve this problem by adaptively adjusting the length of the search, using a hill-climbing heuristic. The emphasis of this paper is to demonstrate how this LS scheme can improve the performance of DE. Experimenting with a wide range of benchmark functions, we show that the proposed new version of DE, with the adaptive LS, performs better, or at least comparably, to classic DE algorithm. Performance comparisons with other LS heuristics and with some other well-known evolutionary algorithms from literature are also presented.     

Simple Expert System for Evaluation of Nutrient Pollution Potential in Groundwater from Manure Application

An expert system for the evaluation of groundwater pollution potential due to leaching of nutrients from land application of manure is developed in this study. The expert system consists of five modules: surface loading, sorption, vadose zone transport, saturated zone transport, and final module. The expert system evaluates the pollution potential in two steps. In the first step, rating values are evaluated for the selected modules. A set of expert system rules is assigned by the writers to evaluate the rating value of each selected module. In the second step, the pollution potential is evaluated from calculating the weighted average rating of the selected modules. Finally, the expert system is validated against a site assessment done by a group of experts for a concentrated animal feeding operation (CAFO) facility in Oklahoma. The advantages of the expert system are its user-friendliness, requirement of easily available input data, and faster evaluation time. The expert system is recommended to the farmers for improving their management practices and for selecting sites suitable for building new CAFOs. It is also recommended to the regulatory agencies as a screening level tool to identify the most vulnerable sites.