Selective and in-situ determination of carbonate and oxide particles in aqueous solution using laser-induced breakdown spectroscopy (LIBS) for wearable information equipment

Laser-induced breakdown spectroscopy (LIBS) has been applied for quantitative analysis of Al₂O₃, CaCO₃ and MgO particles suspended in water. In the single elemental system, the plasma emission intensities of Al, Ca and Mg were linearly increased with concentration of elements in the range of 1.0×10^?5–1.0×10^?3  M, 1.0×10^?4–2.0×10^?3 M and 8.0×10^?5 –4.0×10^?3 M, respectively. We also investigated the concentration dependence of breakdown spectra for suspended mixtures of Al₂O₃, CaCO₃ and MgO particles. The emission lines, such as Al I, Ca I, Ca II and Mg I, were appeared in the LIBS spectrum simultaneously, and each emission peak could be deconvoluted. The plasma emission intensities of Al, Ca and Mg in the multielemental system were also linearly increased with their concentrations in the range of 1.0×10^?5–1.0×10^?3 M, 1.0×10^?4–2.0×10^?3 M and 4.0×10^?4–2.0×10^?3 M, respectively. LIBS was found to be available for quantitative and qualitative measurement of the concentrations of Al₂O₃, CaCO₃ and MgO particles suspended in water. The present results suggest that LIBS is a potentially useful tool for in-situ analysis on particles composition and concentrations for environmental monitoring by the wearable information equipments.     

Static capacitance contrast of LSI covered with an insulator film in low accelerating voltage scanning electron microscope

A new image contrast is reported for LSIs covered with an insulator film in a low accelerating voltage scanning electron microscope. The surface region above the conducting lines is often observed brighter than that without conducting lines. This contrast is quasi-stationarily observed contrary to well-known capacitive-coupled voltage contrast, and is called static capacitance contrast. The optimum irradiation conditions for the maximum image contrast is studied and its mechanism is discussed.     

Microwave-assisted steam distillation for simple determination of polychlorinated biphenyls and organochlorine pesticides in sediments

A novel sample extraction technique for polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) analysis using microwave-heating device is developed. In this study, microwave-assisted extraction (MAE) and steam distillation techniques were combined. Desorption of the anatytes from solid matrixes was accelerated with water vapor which was generated by microwave irradiation. A sample holder in a commercial microwave extraction cell kept the sample from direct contact with the organic solvent for analytes trapping during the treatment process. Therefore, relatively clean extracts were obtained with small amount of solvents. Without any cleanup steps, the obtained extract could be analyzed with gas chromatograph/mass spectrometers (GC/MS). Six PCB congeners (PCB15, 28, 70, 101, 180, 194, 209) and three OCPs (gamma-HCH, 4,4'-DDE, 4,4'-DDD) in two marine sediment samples (a sediment collected from a bay of Kyusyu Island, Japan, and a certified reference material NIST SRM1944) were analyzed by using this microwave-assisted steam distillation (MASD) technique and another extraction method (exhaustive steam distillation, MAE, and Soxhlet extraction); and comparisons of the results are shown in this report. Although recovery yields of highly chlorinated biphenyls (PCB180, 194, 209) and relatively polar OCPs (gamma-HCH, 4,4'-DDD) were low (30-60%) compared with other analytes (PCB15, 28, 70, 101, 4,4'-DDE; recovery, 80-100%), use of isotope labeled internal standards for the MASD technique gave comparable results with the values obtained by other extraction methods and the certified values in the samples.     

Microassembly of semiconductor three-dimensional photonic crystals

Electronic devices and their highly integrated components formed from semiconductor crystals contain complex three-dimensional (3D) arrangements of elements and wiring. Photonic crystals, being analogous to semiconductor crystals, are expected to require a 3D structure to form successful optoelectronic devices. Here, we report a novel fabrication technology for a semiconductor 3D photonic crystal by uniting integrated circuit processing technology with micromanipulation. Four- to twenty-layered (five periods) crystals, including one with a controlled defect, for infrared wavelengths of 3-4.5 microm, were integrated at predetermined positions on a chip (structural error <50 nm). Numerical calculations revealed that a transmission peak observed at the upper frequency edge of the bandgap originated from the excitation of a resonant guided mode in the defective layers. Despite their importance, detailed discussions on the defective modes of 3D photonic crystals for such short wavelengths have not been reported before. This technology offers great potential for the production of optical wavelength photonic crystal devices.     

Polarization-Insensitive Monolithic 40-Gbps SOA–MZI Wavelength Converter With Narrow Active Waveguides

A polarization-insensitive monolithic 40-Gbps semiconductor optical amplifier (SOA)-Mach-Zehnder interferometer wavelength converter has been developed. Based on the photon-electron rate equation, we optimized the dimensions of the waveguide structure to maximize the field confinement in the active layer. An InGaAsP active layer with narrow SOA waveguide effectively enables polarization-insensitive high-speed wavelength conversion. High-precision wafer processing technique enabled the fabrication of submicrometer-wide active waveguides with low current leakage. Input waveguide arrays were fabricated at intervals of 25 mum and mounted in a module with two-lens aspherical lens optics. The 40-Gbps nonreturn-to-zero wavelength conversion experiment demonstrates a clear eye opening over full C-band operation     

Fiber Optic Analog--Digital Hybrid Signal Transmission Employing Frequency Modulation

Investigations are carried out on the SNR performance in fiber optic FM transmission systems which use multimode fibers and 1.3 μm laser diodes. Both laser diode noise and modal noise are quantitatively evaluated in systems with and without employing a superimposed pulse modulation scheme. Based on these investigations, parameters for analog-digital hybrid signal transmission systems employing FM are determined. The hybrid signal consists of audio, video, and 2 Mbit/s digital data. The results obtained in transmission experiments satisfied the design objectives and confirmed the technical feasibility of an analog-digital hybrid transmission employing FM. The obtained results make the fiber optic FM transmission system with a 1.3mumLD an attractive alternative in subscriber systems, and video transmission systems for microwave IF links and CATV trunks.     

Acetylation of loofa (Luffa cylindrica) sponge as immobilization carrier for bioprocesses involving cellulase

The feasibility of using loofa sponge for immobilization of cellulase-producing microorganisms was investigated by acetylating loofa sponge. Acetylation was achieved by autoclaving process of loofa sponge immersed in acetic anhydride at various temperatures for various times. The degree of acetylation, as inferred by the weight percentage gain (WPG), was enhanced by increasing both temperature and the duration of acetylation. The acetylation of a piece of loofa sponge in an autoclave at 120 degrees C for 20 min resulted in a WPG of about 8%, which was sufficient to protect the loofa sponge against cellulose degradation. The acetylated loofa sponge prepared under this condition was not decomposed by commercial cellulase and its structure was maintained for more than 720 h during repeated-batch treatments with commercial cellulase. A flocculating yeast (Saccharomyces cerevisiae IR-2) and a fungus (Trichoderma reesei QM9414) were successfully immobilized in the acetylated loofa sponge. In each case, the percentage of immobilized cells was as high as that obtained using nonacetylated loofa sponge. Acetylation had no adverse effects on cell growth and immobilization of T. reesei QM9414, as well as on cell growth and ethanol production by S. cerevisiae IR-2. T. reesei QM9414 immobilized on an acetylated loofa sponge was successfully used for repeated-batch cellulase production from commercial cellulose powder. Although the acetylated loofa sponge showed a slight weight loss, it was not disintegrated by activated sludge. The results obtained in this study showed that acetylated loofa sponge is suitable as an immobilization carrier for bioprocesses involving cellulase.