Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

基于(火用)效率目标的环冷机余热回收系统操作参数优化

摘要：针对烧结环冷机余热回收利用率不高的难题，采用分析法建立了评价某钢铁厂烧结环冷机余热回收系统运行效率的效率模型。基于多孔介质模型、局部非热平衡方程、真实气体SRK方程建立环冷机内气固两相换热模型。通过CFD仿真模拟，探究料层高度、循环风机输入烟气温度、烧结矿底部入口风速三项可控环冷机运行工艺参数对系统效率的影响规律。结果表明，料层厚度在1～1.5 m区间每增加0.1 m，效率增加0.8%～1.1%；循环风温在100～140℃之间每增加10℃，效率增加1.4%～1.5%；烧结矿底部入口风速在0.9～1.9 m/s之间每增加0.1 m/s，效率降低0.18%～0.24%。在此基础上，基于工业运行数据建立效率正交试验优化模型，提高了该余热回收系统3.42%的效率。     

Delay compensated control of the Stefan problem and robustness to delay mismatch

This paper presents a control design for the one‐phase Stefan problem under actuator delay via a backstepping method. The Stefan problem represents a liquid‐solid phase change phenomenon which describes the time evolution of a material's temperature profile and the interface position. The actuator delay is modeled by a first‐order hyperbolic partial differential equation (PDE), resulting in a cascaded transport‐diffusion PDE system defined on a time‐varying spatial domain described by an ordinary differential equation (ODE). Two nonlinear backstepping transformations are utilized for the control design. The setpoint restriction is given to guarantee a physical constraint on the proposed controller for the melting process. This constraint ensures the exponential convergence of the moving interface to a setpoint and the exponential stability of the temperature equilibrium profile and the delayed controller in the norm. Furthermore, robustness analysis with respect to the delay mismatch between the plant and the controller is studied, which provides analogous results to the exact compensation by restricting the control gain.     

Automated network management and configuration using Probabilistic Trans-Algorithmic Search

Online configuration of large-scale systems such as networks requires parameter optimization within a limited amount of time, especially when configuration is needed as a response to recover from a failure in the system. To quickly configure such systems in an online manner, we propose a Probabilistic Trans-Algorithmic Search (PTAS) framework which leverages multiple optimization search algorithms in an iterative manner. PTAS applies a search algorithm to determine how to best distribute available experiment budget among multiple optimization search algorithms. It allocates an experiment budget to each available search algorithm and observes its performance on the system-at-hand. PTAS then probabilistically reallocates the experiment budget for the next round proportional to each algorithm’s performance relative to the rest of the algorithms. This “roulette wheel” approach probabilistically favors the more successful algorithm in the next round. Following each round, the PTAS framework “transfers” the best result(s) among the individual algorithms, making our framework a trans-algorithmic one. PTAS thus aims to systematize how to “search for the best search” and hybridize a set of search algorithms to attain a better search. We use three individual search algorithms, i.e., Recursive Random Search (RRS) (Ye and Kalyanaraman, 2004), Simulated Annealing (SA) (Laarhoven and Aarts, 1987), and Genetic Algorithm (GA) (Goldberg, 1989), and compare PTAS against the performance of RRS, GA, and SA. We show the performance of PTAS on well-known benchmark objective functions including scenarios where the objective function changes in the middle of the optimization process. To illustrate applicability of our framework to automated network management, we apply PTAS on the problem of optimizing link weights of an intra-domain routing protocol on three different topologies obtained from the Rocketfuel dataset. We also apply PTAS on the problem of optimizing aggregate throughput of a wireless ad hoc network by tuning datarates of traffic sources. Our experiments show that PTAS successfully picks the best performing algorithm, RRS or GA, and allocates the time wisely. Further, our results show that PTAS’ performance is not transient and steadily improves as more time is available for search.     

基于3D打印技术复制砂浆节理的剪切试验及峰值抗剪强度模型

为进一步研究节理三维形貌特征与节理峰值抗剪强度的关系,首先采用巴西劈裂试验获取了自然劈裂岩石表面,通过三维扫描技术获取了节理面形态的高精度点云,通过逆向建模得到了自然岩石表面的立体模型,结合3D打印技术制作出了与自然岩石表面一致的PLA模具,以3D打印获得的底模通过水泥砂浆浇筑了含有自然结构面形貌的相似节理面试样。PLA模具与复制材料差异较大,复制材料在凝结过程中不易与PLA模具黏结,进而使脱模过程较为方便,不会破坏节理面。同时PLA模具可重复进行相似材料复制工作,具有可重复使用的优点。然后进行了具有5组形貌面的20个水泥砂浆节理面在4种不同法向荷载情况下的结构面剪切试验,得到了结构面剪切位移-荷载曲线。研究了结构面峰值抗剪强度、峰值位移、剪切刚度影响因素。节理经过剪切后形貌面出现不同程度的磨损,其磨损范围与等效高差分布范围基本一致,并且在等效高差为剪断破坏模式且成片的区域磨损较为严重。在新粗糙度指标基础上提出了新的峰值抗剪强度模型,经试验对比显示出新模型的有效性。在新模型基础上提出了一个简化模型。对比发现新模型简化后其计算精度较新模型有所降低但由于所需参数减小计算较为方便,新模型简化结果精度虽然有所下降但是还是比Barton公式精度高。     

基于液压活塞式惯容器的车辆悬架性能研究

阐述了液压活塞式惯容器的基本结构、工作原理与承载力大的特点，建立了考虑摩擦力、寄生阻尼力和油液弹性效应的惯容器非线性力学模型。在数控液压伺服激振台上对液压活塞式惯容器进行了力学性能试验，基于试验结果，利用Matlab参数辨识工具箱对非线性力学模型中的参数进行辨识。在此基础上建立了包含液压活塞式惯容器非线性因素的车辆惯容器 弹簧 阻尼器（inerter-spring-damper，简称ISD）悬架动力学模型并进行了仿真分析。结果表明，当考虑液压活塞式惯容器非线性因素时，车辆ISD悬架系统的车身加速度均方根值增加5%，而轮胎动载荷与悬架动行程均方根值均有所减小,降低了车辆的行驶平顺性。     

基于最小维修的石化安全设备区间截尾寿命数据分析

在石化安全关键设备寿命截尾数据的可靠性评估过程中，为避免传统可靠性评估方法未考虑维修对故障间隔时间的影响，以及中值填充法误差较大的缺点，本文提出了一种逆变换区间截尾数据填充方法。首先，在可修系统基于最小维修的假设下，通过非齐次泊松过程描述系统的故障趋势，利用逆变换填充得到监测区间的缺失数据；随后根据蒙特卡罗期望最大化算法，获得填充数据的参数估计值。通过蜡油加氢装置紧急泄压阀的案例分析，该算法能够很好地融合已有数据，得到的形状参数估计值偏差与中值填充法相比缩小4%以上，从而验证了该算法的有效性；这有助于安全关键设备的定量化完整性管理，保障石化装置平稳运行。     

宁夏宁东供水工程主机设备形式参数选择与国际招标

宁东供水工程供水水泵共有卧式和立式离心泵2种方案可供选择,也是工程论证时争论的焦点,经综合比较及主机设备的国际招标,最终确定了奥地利安德里兹公司的卧式双吸中开式离心泵为宁东供水工程的供水水泵。     

测试(试井)成果影响因素浅析

随着测试技术的发展、测试质量及资料解释水平的提高，测试（试井）成果的可靠程度越来越受到重视。影响解释成果的环节和因素很多，从客观和主观两方面分析其主要因素，找出症结所在，从而完善现场环节，完善资料解释过程，提高测试技术及解释水平。     

测井资料在优选压裂层位中的应用

压裂是低孔、低渗油层改造的主要增产措施。根据常规测井资料、岩石物理实验分析数据及试油成果。研究储层四性关系，确定区块的低孔、低渗储层评价标准。进一步对油层进行分类，有针对性地为油层压裂提供施工层位和准确的储层参数。通过商543区块实例，阐述了选择压裂层位的方法。