蒸发器泄漏原因分析及处理

对锦州石化分公司第三套催化裂化装置系统蒸发器泄漏原因进行了分析,并提出处理措施。收到较好的效果。     

激光导向伺服系统中满意PID调节器的LMI设计

利用带有图像处理功能的小型激光导向伺服系统,可以大大降低目标坐标测定仪操作手跟踪动态飞行目标的操作难度,从而提高激光回波率.与经典的矩阵分解方法不同,本文以线性矩阵不等式方法,研究了激光导向伺服系统的满意PID调节器设计问题.首先从约束指标的相容性出发,给出满足与给定圆形极点约束相容的输出方差的取值范围.然后,在此取值范围内,得到了求取同时满足上述两种约束的PID调节器参数的方法.靶场试验结果证明了其有效性.     

广西水利工程管理单位亏损情况及扭亏措施

广西国营水利工程管理单位运行困难，亏损严重。为此对亏损情况及存在问题进行分析，提出相应措施及扭亏为盈的弥补思路。     

预应力钢筒混凝土管穿越地下管线的施工措施

文中介绍了预应力钢筒混凝土管的概念、优越性，并结合山西省万家寨联接段引黄工程的实际施工，总结出了穿越各种地下管线的施工经验。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Introduction of a nonlinearity measure for principal component models

Although principal component analysis (PCA) is an important tool in standard multivariate data analysis, little interest has been devoted to assessing whether the underlying relationship within a given variable set can be described by a linear PCA model or whether nonlinear PCA must be utilized. This paper addresses this deficiency by introducing a nonlinearity measure for principal component models. The measure is based on the following two principles: (i) the range of recorded process operation is divided into smaller regions; and (ii) accuracy bounds are determined for the sum of the discarded eigenvalues. If this sum is within the accuracy bounds for each region, the process is assumed to be linear and vice versa. This procedure is automated through the use of cross-validation. Finally, the paper shows the utility of the new nonlinearity measure using two simulation studies and with data from an industrial melter process.     

Reconstruction of Mandibular Defect with Porous β-TCP/BMG Artificial Bone

1Introduction Reconstructivesurgeryisoneofthehottestre searchedsubjectsthatdealingwithbonedefects.Thetra ditionalmethodisimplantationoffreshautograftbonebe causeofitsnon immunoreactiveproperty.Butautologousbonewasnotabundantinsomecases.Sowefoundbeta trica…     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

Preparation and Compressive Stress Effect of Polymer Matrix RE-Fe Giant Magnetostrictive Composite

Polymer matrix RE-Fe giant magnetostrictire composite （GMPC） was prepared using bonding and magnetic field forming technique, and magnetostriction of samples was measured for different compressive stress. The experimental results show thai there is certain compressive effect in GMPC. And the influence of compressive stress on magnetostriction of sample was investigated. It offers essential reference for application and device design of GMPC.