塔河油田超深自喷井流态特征分析

针对塔河油田油藏埋藏深、原油粘度高、井筒热损失大导致自喷困难的实际问题，根据热量传热原理和两相流动理论，建立了自喷井中产出液沿井筒流动与传热的热力学模型。运用该模型计算了塔河油田5口稠油井产出液沿井筒的温度和压力分布。计算结果表明。随着产出液沿井筒的举升。压力逐渐减小，温度不断下降。当温度下降到一定数值时。原油粘度明显增大，即对应原油的拐点温度出现。因此，可以根据流态特征来估计该原油的拐点温度，为选择合适的降粘方法和降粘深度提供了技术指导。     

一种基于小波变换的OTDR事件分析算法的研究

简单分析了用 OTDR卡进行光纤检测的原理 ,根据小波分析检测信号突变点的理论 ,提出了运用小波分析对光纤断点及反射事件准确定位的方法。理论分析和实例计算表明 ,这种方法对 OTDR曲线中反射事件尤其是断点的定位非常准确 ,是一种行之有效的方法     

公伯峡变压器中性点经小电抗接地对线路操作过电压的影响

变压器中性点经小电抗接地可以有效地限制单相短路电流。文章就中性点小电抗的接入对系统的操作过电压的影响进行了研究。通过计算和分析表明：变压器中性点接入小电抗对系统的操作过电压基本不会产生影响。     

焦化加热炉爆管故障分析与预防

焦化加热炉炉管内的物料通常为有杂质容易结焦的混合渣油,如果设计不合理、操作控制不当、运行周期过长等,极易造成炉管爆管事故。以2005年9月大庆石化分公司炼油厂焦化加热炉爆管故障为例,阐述了焦化加热炉的爆管原因、故障处理及预防措施,认为注水量小、渣油中含催化剂、负荷偏离设计工况、烧焦周期和烧焦速度不当等引起严重结焦是爆管的主要原因。     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

An introduction to Wu's method for mechanical theorem proving in geometry

Wu's algebraic method for mechanically proving geometry theorems is presented at a level as elementary as possible with sufficient examples for further understanding the complete method.The work reported here was supported by NSF Grant DCR-8503498.     

论校园文化和德育目标的一致性

中系统介绍了校园化和德育目标的关系，并找准两之间的结合点，通过分析两的一致性和辩证统一关系，达到育人目的。     

The Problem of Estimating the Uncertainty of the Fixed Point Temperature Due to the Presence of Impurities

The main problems in estimating the uncertainty due to the presence of impurities in the material: the absence in the documents of a unique definition of the quantity being measured – the fixed point temperature, the lack of agreed methods of realizing the fixed points and the insufficient justification of the equations used for the estimate, are analyzed. The results of a measurement of the melting point of gallium are presented, which differ in the conditions in which they were realized – with one and two liquid-solid interfaces and different solidification conditions, are presented. The reasons for the considerable difference between the values of the temperatures obtained in these experiments are discussed.     

铜铟铋硫对Sn-Ag基无铅焊料性能的影响

研究了Cu、In、Bi、S元素对Sn-Ag基无铅焊料熔点和铺展性的影响。结果表明:Sn-Ag-Cu三元合金成分为95.5%Sn3.5%Ag1%Cu时具有较低熔点(215℃)和好的铺展性;加入适量的In可降低Sn-Ag合金的熔点和改善铺展性能;随w(Bi)的增加Sn-Ag-Bi三元合金的熔点降低、铺展性变好;Sn-Ag合金的熔点随w(S)的增加而升高,加入少量S能改善Sn-Ag合金的铺展性。     

工业层析洗梯液回收套用的一种方法

以生产甲胺基阿维菌素苯甲酸盐精品的工艺——工业层析产生的洗梯液回收套用的过程为例，说明利用二元恒沸物的组成随压力的变化而变化的规律，对生产洗梯液进行有效、简洁、合理分离及套用的方法。