PEN/PTT共混聚酯的熔融行为

利用差示扫描量热仪对不同配比的聚萘二甲酸乙二醇酯/聚对苯二甲酸丙二醇酯(PEN/PTT)共混体系的熔融行为进行了分析,发现在共混体系中两组分形成各自的晶体,PEN和PTT的熔点均随另一组分含量的增加而下降。根据Nishi-Wang方程,按300℃计算,由PEN/PTT共混体系中PEN熔点下降计算所得到的相互作用能密度为-0．214 2 J/cm~3,相互作用参数为-0．006 8,表明PEN/PTY共混体系在熔融态是热力学性质稳定的相容体系。     

低温流动性改进剂对低凝柴油性能的影响

通过考察几种低温流动性改进剂的活加量对常一线馏分、常二线馏分、常三线馏分、催化轻柴油等基础调合组分以及成品柴油冷滤点的影响,对以华北油田原油为原料生产低凝柴油的油品调合进行了研究。结果表明Ｄｏｄｉｆｌｏｗ４１３８和ＰＳＭ可做为华北石油管理局第一炼油厂生产柴油时的低温流动性改进剂,并确定了两种适宜的柴油生产方案。     

On the Predominant Electron-Donicity of Polar Solid Surfaces

The reasons for the predominant electron-donicity of almost all solid polar surfaces and its implications are discussed in this paper. By contact angle or interfacial tension measurements, the electron-accepting as well as the electron-donating properties of polar liquids can be ascertained, through the interplay between their energies of adhesion and cohesion. For the solid-liquid interface, direct interfacial tension measurements are not possible, but indirectly, solid/liquid interfacial tensions of polar systems can be obtained by contact angle measurement. However, as the energy of cohesion of a solid does not influence the contact angle formed by a liquid drop placed upon its surface, one can only measure the solid surface'ks residual polar property, manifested by the energy of adhesion between solid and liquid. This residual polar property is of necessity the dominant component; in most cases this turns out to be its electron donicity. When, by means of contact angle measurements with polar liquids, both electron-accepting and electron-donating potentials are found on a polar solid, it is most likely still partly covered with a polar liquid: usually water. The amount of residual water of hydration of a polar solid follows from its polar (Lewis acid-base) surface tension component (γ^AB). The degree of orientation of the residual water of hydration on a polar solid can be expressed by the ratio of the electron-donating to electron-accepting potentials (γ^⊖/γ^⊕), measured on the hydrated surface.     

Improvement of polymer blend properties by changing sequence of mixing

The basic objective of this article is to improve the polymer blend properties by changing mixing sequence. Blending of two elastomers does not lead to a molecularly homogeneous blend (true solution), but to a heterogeneous system in which both polymer phases are present. In this article, the detailed study of heterogeneous distribution of carbon black as well as blend inhomogenity and the physicomechanical including dynamic mechanical properties of the blend has been carried out. The choice of the blend was natural rubber/polybutadiene rubber as 85:15. Heterogeneous carbon black distribution study was also performed in differential scanning calorimeter. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2735–2742, 2007     

Crystallization behavior of dry‐brush PEO‐PS block copolymer and PEO homopolymer blend

The crystallization behavior of semicrystalline PEO homopolymer/triblock PS‐PEO‐PS copolymer blend system, which exhibited “Dry‐Brush” in the melt. A symmetric polystyrene–poly(ethylene oxide)–polystyrene triblock copolymer was blended with PEO homopolymer (h‐PEO) having the same molecular weight as that of the PEO block in the copolymer. Considering the composition of the blend (W_ps ≥ 0.8), PEO spheres were formed in the blend. Because of the dry‐brush phase behavior of this blend, h‐PEO added was localized in the PEO microdomains, which increases the domain size without changing the microdomain morphology. The crystallization of PEO block was confined within the microdomains and the crystallization temperature was about 60°C lower than normal. Self‐seeding tests were performed to clarify the nucleation mechanism of the blend. Because the droplets size varies greatly, multicrystallization peaks were witnessed in the self‐seeding process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

煤岩配煤技术的发展与现状

煤岩学在炼焦配煤技术上的应用,使炼焦配煤手段更有效,使焦炭质量预测在生产上应用成为可能,为定性的经验配煤技术跃变到定量的科学配煤技术创造了条件。夏皮洛煤岩配煤技术是目前较好的配煤方法,其相关系数可达0.93;国内许多学者在煤岩配煤方面也做了大量研究工作,有些相关系数达0.98。目前虽然各种方法存在一定局限性,但随着计算机和图像处理技术的发展,煤岩学在指导配煤技术方面将有新的突破。     

Surface hydrolysis of filaments based on poly(trimethylene terephthalate) spun at high spinning speeds

The surface alkaline hydrolysis of fibers made from poly(trimethylene terephthalate) (PTT) was studied after extruding the polymer at high spinning speeds from 2000 to 6000 m/min and heat setting in the range of temperatures from 100 to 180°C. Fiber weight loss increased with an increasing heat‐setting temperature but it was also dependent on the spinning speed. Some of the partially hydrolyzed fibers had a well‐developed, hydrophilic surface, and pore size in the range of 0.69 to 1.20 μm. The optimum reaction and morphological conditions for increasing porosity in PTT fibers depends on spinning speed and heat‐setting temperature. A temperature of 180°C is the upper limit for heat‐setting PTT filaments but seems to be the most effective for making porous fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1724–1730, 2004     

PP/PVC/PP-g-(St-co-MMA)的形态结构

以苯乙烯一甲基丙烯酸甲酯共聚物接枝聚丙烯[PP—g-（St—co—MMA）]为相容剂，利用扫描电子显微镜（SEM）和x射线能谱仪（EDS）对PP／PVC／PP—g-（St—co-MMA）的形态结构进行了研究。由x射线能谱微区分析得到了共混物中氯元素面分布图，对氯元素面分布进行了粒径统计。结果表明，在PP／PVC中加入PP-g-（St—co—MMA）相容剂，共混物亚微观相形态结构发生了变化。PP—g-（St—co—MMA）能够明显降低PP／PVC共混物中PVC分散相的分散尺寸，提高共混物两相之间的相容性。改变相容剂的用量和共混物的组成，都对体系的形态结构产生影响。     

MTBE辛烷值测试法的探讨

MTBE作为调合生产高标号无铅汽油的重要的高辛烷值组分油，准确测试其辛烷值在汽油调和生产中具有重要的意义。初步探讨了MTBE研究法辛烷值的测试方法，尝试了用甲苯标准燃料做参比燃料直接测定其净辛烷值，同时也测定了MTBE的混配辛烷值，通过MTBE辛烷值的测试，了解了MTBE的调和效应，确认了在石油二厂无铅汽油调和生产中对催化汽油的MTBE的真实辛烷值约为108／RON，指导了车用无铅汽油的调和生产。     

Polar and Non-Polar Solvent Permeation Resistance of Blow-Molded Bottles of Polyethylene/Blends of Modified Polyamide and Polyamide 6 Clay Nanocomposite

Investigations on white spirit and acetone permeation resistance of modified polyamide and nylon 6 clay (MPANYC) blends and their corresponding polyethylene/MPANYC bottles were reported in this study. The white spirit and acetone permeation resistance of MPANYC sheets improve consistently with increasing NYC contents present in MPANYC resins after blending nylon 6 clay (NYC) in modified polyamide (MPA) resins. However, the order of barrier improvement of the PE/MPANYC and PE/NYC bottle specimens is not corresponding to the order of barrier improvement of the MPANYC and/or NYC barrier resins added in PE. The blow-molded PE/NYC bottle specimen exhibits similarly worse white spirit and acetone solvent permeation resistance as the PE bottle specimen, wherein no clearly formed NYC laminas but only dispersed NYC droplets or agglomerates were found on the fracture surfaces of the PE/NYC bottles. However, after blending optimum compositions of MPANYC in PE, the PE/MPANYC bottles with demarcated MPANYC laminas exhibit significantly better white spirit and acetone permeation resistance than the PE/MPA bottle, wherein the white spirit and acetone permeation rates of the PE/MPA₈NYC₁ bottle are about 1.3 and 1.4 times slower than those of the PE/MPA bottle, respectively. In order to understand these interesting barrier properties of PE/MPANYC and PE/NYC bottles, rheological, thermal, wide angle X-ray diffraction and morphological properties of the base MPANYC and NYC resins and their corresponding morphology present in the blow-molded bottles were investigated.