基于遗传算法的产品制造的优化调度

研究了企业产品制造的调度问题 ,并建立了调度的最小模型。引入效率函数 ,运用遗传退火进化算法实现了调度决策的优化 ;提出了将遗传退火算法和分派规则相结合的调度策略和动态编码的方法 ,放宽了约束条件 ,提高了搜索效率和速度 ,保证其全局收敛性。     

路径长度受限的随机需求VRP的模型和算法

路径长度受限的随机需求VRP在生产、生活中有着广泛的应用。给出了路径长度受限的随机需求VRP问题的线性整数规划模型,在不允许部分服务和仅能服务失败一次的策略下设计了一个启发式算法。该算法以离散优化中广泛应用的扫描算法为基础生成服务的一个初始可行方案,然后利用模拟退火算法改进得到近似最优解。对需求为二项分布的50个结点、1个服务中心的问题进行了数值试验,数值结果表明该算法对求解路径长度受限的随机需求VRP是有效的。     

铁电薄膜存储器底电极Pt/Ti的制备及性能研究

应用射频磁控溅射方法 ,在Si基片上采用不同的溅射工艺制备了铁电薄膜底电极Pt/Ti,并分析了在不同温度下退火后材料的电导率性能和粘结力性能 ,从理论和实验上分析了不同的溅射工艺和退火处理对底电极性能的影响。     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002     

烷烃中少量芳烃的固定床和模拟移动床吸附

在实验研究烷烃中少量芳烃的固定床吸附动态过程和模拟移动床吸附动态过程的基础上,用固定床和模拟移动床线性推动力模型进行了模拟计算,可得到如下结论:在本文的实验条件下,固定床吸附动态模型和模拟移动床吸附动态模型拟合的结果均与实验值相符;但从技术性能指标和技术经济指标两个角度都反映出对脱除烷烃中的少量芳烃的吸附分离过程,用固定床吸附过程比模拟移动床吸附过程更具有可行性。这些结果为在直链烷基苯的生产过程中,降低循环烷烃中芳构化物的含量,实现延长脱氢催化剂的寿命,提高烷基苯的产量提供了技术基础。     

星型聚合物破乳剂的合成与性能研究

采用“发散法”合成了以乙二胺为核心 1 0～ 3 0代的系列星型聚合物—聚酰胺 -胺(PAMAM)。采用IR、NMR和端基分析等手段对PAMAM的结构进行了表征并考察了这类聚合物对O/W型模拟原油乳液的破乳性能。结果表明 :随着支化代的增加 ,破乳性能提高。在 4 5℃、添加量为 15 0mg/L、90min的条件下 ,3 0代产品的破乳率达到 98 5 %。     

一种检测单晶炉热场温度的新方法

为去除单晶炉热场温度测量信号中的低频干扰、提高温度信号的估计精度,本文提出了一种基于跨维模拟退火(trans dimensional simulated annealing,TDSA)的单晶炉热场温度检测方法.该方法首先将AIC(Akaike information criterion)信号个数判断准则纳入采样机制中以便对干扰个数采样估计,进而利用所设计的基于信号频谱和轮盘赌思想的Metropolis Hastings机制对相应个数的干扰频率进行采样,最后设计了混合均匀和高斯采样机制对单晶炉热场温度进行采样估计.仿真和单晶炉工程实验结果表明,该方法在干扰个数未知的情况下,能够有效地抑制低频干扰、准确检测单晶炉热场的温度.     

Effect of thermal hysteresis on the gas permeation properties of 6FDA‐based polyimides

The effect of thermal hysteresis on the polymer chain packing and permeation properties of two 6FDA‐based polyimide isomers was investigated. Thermal quenching resulted in a small increase in the fractional free volume of the polyimides with respect to the samples that had been annealed. Quenching from above the glass‐transition temperature also resulted in larger increases in the permeabilities for both 6FDA–6FmDA and 6FDA–6FpDA with respect to annealed samples. Meta‐connected 6FDA–6FmDA exhibited a larger increase in the permeability after quenching than the para‐connected isomer, 6FDA–6FpDA. This larger increase in the permeability for 6FDA–6FmDA may have been due to differences in the effects of the increases in the free volume on the intersegmental resistance to chain motions. Although physical aging over a 3‐month period resulted in a reduction in the permeability of quenched samples of 6FDA–6FpDA, the quenched samples maintained higher permeabilities than the annealed samples. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1174–1182, 2004     

NiCr薄膜微加热器在低温环境下的电学特性研究

设计了一种适用于深低温环境的微型加热器。使用AC磁控溅射技术将NiCr(80/20 at.%)合金沉积到SiO2/Si基底上,并采用微加工工艺实现薄膜图形化,作为加热器的加热元件。研究了NiCr薄膜的电学性能和晶体结构与退火条件之间的关系。实验表明:在450℃氮气环境下退火30min,可以获得深低温性能优良的NiCr加热器。该加热器在20K时的电阻温度系数(TCR)为80.80×10-6/K。X射线衍射(XRD)分析显示NiCr薄膜在450℃氮气环境下退火后,薄膜的结晶度增大,因此,退火条件对薄膜的电阻率和电阻温度系数有较大的影响。     

应用静电纺丝法制备PZT纳米纤维薄膜

提出应用静电纺丝法制备PZT纳米纤维薄膜。研究中配制PZT溶液后再进行静电纺丝,获得了PZT纳米纤维薄膜,并且通过调整纺丝时间和沉积次数来控制纳米纤维薄膜的厚度。运用SEM对获得的热处理前后的薄膜进行了观察对比,测量其平均直径约为200 nm;运用XRD对退火后的样品进行分析,测得样品的主要成分为Pb(Zr0.52Ti0.48)O3,证明所制备的正是PZT薄膜;运用AFM测得薄膜的表面粗糙度为1.034 nm,说明该纳米薄膜材料非常的均匀整齐。