Formation of ST12 phase Ge nanoparticles in ZnO thin films

In this work, we focus on the Ge nanoparticles (Ge-np) embedded ZnO multilayered thin films. Effects of reactive and nonreactive growth of ZnO layers on the rapid thermal annealing (RTA) induced formation of Ge-np have been specifically investigated. The samples were deposited by sequential r.f. and d.c. sputtering of ZnO and Ge thin film layers, respectively on Si substrates. As-prepared thin film samples have been exposed to an ex-situ RTA at 600 °C for 60 s under forming gas atmosphere. Structural characterizations have been performed by X-ray Diffraction (XRD), Raman scattering, Secondary Ion Mass Spectroscopy (SIMS), and Scanning Electron Microscopy (SEM) techniques. It has been realized that reactive or nonreactive growth of ZnO layers significantly influences the morphology of the ZnO: Ge samples, most prominently the crystal structure of Ge-np. XRD and Raman analysis have revealed that while reactive growth results in a mixture of diamond cubic (DC) and simple tetragonal (ST12) Ge-np, nonreactive growth leads to the formation of only DC Ge-np upon RTA process. Formation of ST12 Ge-np has been discussed based on structural differences due to reactive and nonreactive growth of ZnO embedding layer.     

硼氢化钠对滑轮用铸钢板化学镀Ni-B合金薄膜性能的影响

在滑轮用铸钢板上化学镀Ni-B合金薄膜,并研究了硼氢化钠的质量浓度对化学镀Ni-B合金薄膜性能的影响。结果表明:适当增加硼氢化钠的质量浓度,有利于增大化学镀Ni-B合金薄膜的厚度及硼的质量分数,从而提高化学镀Ni-B合金薄膜的硬度。当硼氢化钠的质量浓度大于1.2 g/L时,硼氢化钠的水解速率加快及剧烈的析氢反应,导致化学镀Ni-B合金薄膜的厚度及硬度有所降低。当硼氢化钠的质量浓度为1.2 g/L时,化学镀Ni-B合金薄膜表面"胞状"颗粒均匀、致密,摩擦因数和磨损率最低,具有最佳的耐磨性。     

YSZ/MoS2 self-lubricating coating fabricated by thermal spraying and hydrothermal reaction

Thermal sprayed ceramic coatings have extensively been used in components to protect them against friction and wear. However, the poor lubricating ability severely limits their application. Herein, yttria-stabilized zirconia (YSZ)/MoS₂ composite coatings were successfully fabricated on steel substrate with the combination of thermal spraying technology and hydrothermal reaction. Results show that the synthetic MoS₂ powders are composed of numbers of ultra-thin sheets (about 7 ~ 8?nm), and the sheet has obvious lamellar structure. After vacuum impregnation and hydrothermal reaction, numbers of MoS₂ powders, look like flowers, generate inside the plasma sprayed YSZ coating. Moreover, the growing point of the MoS₂ flower is the intrinsic micro-pores of YSZ coating. The friction and wear tests under high vacuum environment indicate that the composite coating has an extremely long lifetime (>?100,000 cycles) and possesses a low friction coefficient less than 0.1, which is lower by about 0.15 times than that of YSZ coating. Meanwhile, the composite shows an extremely low wear rate (2.30?×?10^?7 mm³ N^?1 m^?1) and causes slight wear damage to the counterpart. The excellent lubricant and wear-resistant ability are attributed to the formation of MoS₂ transfer films and the ultra-smooth of the worn surfaces of hybrid coatings.     

Isolation of the effect of the hairy layer length on the mechanical properties of waterborne coatings

The effect of the acidic hairy layer length on the interdiffusion of polymer between particles and as a consequence on the mechanical properties of the films produced from waterborne coatings has been studied. In order to isolate this effect, latexes with the same particle diameter and molecular weight but stabilized with poly(acrylic acid)-block-poly(butyl acrylate) (PAA-b-PBA) block copolymers of controlled and different lengths were prepared. Tensile strength measurements showed at the macroscopic level that the presence of AA chains in the particle surface reduced the mechanical properties of the films dried at room temperature, being its effect worse the longer the AA chain length. Higher annealing temperatures erased the negative effect of the acidic hairy layer on mechanical properties. The neutralization with NaOH instead of with NH₄OH also led to worse mechanical properties. These macroscopic results were supported by Fluorescence Resonance Energy Transfer (FRET) experiments that showed that at the microscopic level, the extent of interdiffusion occurred slower when the AA chains in the particles surface increased, the annealing temperature was lower and when NaOH was used as neutralizing agent instead of NH₄OH.     

油藏中分散非连续残余油膜的驱替机理分析

水驱后的残余油膜将贴于孔隙壁面，为壁面边界层流体，处于三相界面的包围和共同作用下。目前的调研结果显示，油膜的组成及力学特性沿孔壁方向上是变化的。在化学驱过程中油膜不仅受到驱油剂的驱替作用。还受驱油剂／油界面张力、油／固体界面张力及驱油剂／固体界面张力的阻碍作用。由于油膜组成、力学特性及相间作用的复杂性．以往对油膜驱替机理的研究都是从微观实验的角度对现象作观察和定性解释。本文根据水驱后残余油膜在油藏孔隙中存在的特点，提出了油膜驱替的简化模型。基于油膜驱替的微观实验，采用数值方法从定量的角度分别计算了不同黏弹性驱油剂在不同的驱油剂／原油界面张力作用下对残余油膜的驱替效率。考察了驱油剂的流变性、驱油剂／油界面张力、驱替速度等因素对驱替不同厚度油膜的影响规律。进一步探讨了驱油剂／原油界面特性和流变性在驱替残余油中的综合作用。研究结果表明，驱油剂对油膜的驱替始于驱油剂／油界面，要同时克服驱油剂／油界面约束力和油膜的屈服应力。降低界面张力、增强驱油剂的黏弹性、增加驱替速度，有利于提高驱替残余油膜的驱替效率。适当增加驱油刑的黏弹性可以放宽驱替薄油膜时对超低界面张力的要求。图13参9。     

梁112块沙四段薄互层低渗透油藏水力压裂工艺优化

梁112块沙四段薄互层油藏属于典型的高压、特低渗透油藏,具有油层多、单层薄、砂岩与泥岩交互等特点。常规压裂效果不理想。通过建立单井模型,确定了压裂应以增加裂缝的长度为主;利用FracproPT软件模拟优化加砂规模;根据油层物性特点优化射孔方案;配套应用粉陶降滤和控制缝高等技术优化了水力压裂工艺。2004年共对11口井实施了大型水力压裂,平均加砂量为42.5m3,平均加砂强度为1.6m3/m,累积增产原油达2.75×104t。     

Effect of select parameters on the properties of edible film from water-soluble fish proteins in surimi wash-water

Edible film from water-soluble fish proteins were developed by casting film solution on leveled trays and effects of pH (9.5, 10.0 and 10.5), heating temperature (60, 70 and 80 °C), and heating time (10, 20 and 30 min) of the film solution on various film properties were determined using Response Surface Methodology (RSM). The impact of pH and heating temperature of film solution was more significant, overall, on the film's properties than heating time. Contour plots of tensile strength and elongation at break was highest at pH of 10.0 at 70 °C (2.75-3.02 MPa) but low in elongation at break (6.35-9.16%), while water vapor permeability and oxygen permeability were at their lowest (58.55-65.96 g mm/m² d kPa and 351.33-624.18 cm³ μm/m² d kPa). There was a direct correlation between the films’ and proteins’ solubility on one hand, and heating temperature of film solution on the other, which reversed with change in pH of film solution. Film color was darker and more yellowish with increase in the pH of film solution.     

新型高K栅介质ZrO2薄膜材料的制备及表征

采用超高真空电子束蒸发法制备了新型高 K栅介质-非晶 ZrO2薄膜. X射线光电子能谱 (XPS) 中 Zr3d5/2 和 Zr3d3/2 对应的结合能分别为 182.1eV和 184.3eV, Zr元素的主要存在形式为 Zr4+,说明薄膜由完全氧化的 ZrO2组成 ,并且纵向分布均一.扩展电阻法( SRP)显示 ZrO2薄膜的 电阻率在 108Ω@ cm以上,通过高分辨率透射电镜( HR- XTEM)可以观察 ZrO2/Si界面陡直,没有 界面反应产物 ,证明 600℃快速退火后 ZrO2薄膜是非晶结构.原子力显微镜( AFM)表征了薄膜的 表面粗糙度,所有样品表面都很平整,其中 600℃快速退火样品 (RTA)的 RMS为 0.480nm.     

利用静电学和测量数据对碳纳米管膜场致发射规律的定量分析

碳纳米管膜的场致发射电流密度仅由它表面的宏观电场决定，无论其表面形状是平的还是半球状的。对于理想的平行板电极系统，其表面电场强度均匀（UId），发射电流密度、总电流与发射面积成正比：对于半球一平面电极系统半球形的阴极存在一个宏观场增强因子ks，一个与两极距离和球半径之比（d/r）相关的函数，其表面的平均场强为ks U/d。对于d/r=0，ks=1，d≥r的情况，ks接近于常数。对于10〈d／r〈100的情况，存在一个经验的表达式：ks=1＋0．15d/s=0．005（d／r）^2。在引入ks后，不同作者给出的平面电极系统和半球一平面电极系统碳纳米管膜的场致发射电流I与宏观表面电场强度E的关系都可以近似用-经验公式描述：I=a（E-Eo）^b，a，b为常数。该经验公式可为稳定生产的CNT膜片应用产品设计提供方便。     

Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…