引进型国产300MW汽轮机窜轴事故分析及防止对策

通过引进型国产300MW汽轮机在启动试运中出现的一次窜轴事故,根据计算机追忆打印的有关图表、数据分析了产生事故的原因,并提出了为防止类似事故重演应采取的措施和建议。经采取措施后该机组多次又在相同情况下启机,已安全运行。说明分析正确,措施得当,值得同类型机组借鉴。     

微机核子秤在大型尿素装置中的应用

介绍了大型尿素装置中微机核子秤的系统构成，测量原理、安装、调校及在调试过程中发现的问题。     

改进电炉变压器有载调压开关的探讨

分析了目前使用的电炉变压器调压开关的原理及存在的问题，结合生产实际提出了改进方案。     

家电产品常用板材的选用

本文首先介绍国内和日本、德国、俄罗斯等国冷轧薄钢板及镀锌薄钢板的牌号、标记识别及生产地及与我国家标准薄钢板牌号的相互之间的关系，并比较具体地介绍冷轧板的实效性、镀锌薄钢板的锌层特性等诸多方面的状况。从而帮助我们在设计、制造家电产品中，比较正确地选择合适的板材。     

苦味酸钾点火药在电点火头中的应用

通过理论分析和试验,从机械感度、燃烧精度、热安定性、性能、长贮等方面,对比分析了苦味酸钾点火药与DDNP点火药.结果表明:在电点火头制造中,采用苦味酸钾作为点火药的主要组分,具有热稳定性好、药头机械强度高、生产过程废品少、无环境污染等优点,尤其有利于提高电雷管的发火可靠性和一致性.     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

First-principle study of ferroelectricity in PbTiO3/SrTiO3 superlattices

We performed the first-principles calculation to investigate the electronic structure and polarization behaviors in PbTiO₃/SrTiO₃ (PST) superlattices. The DOS (density of state) profiles show that there are strong hybridizations of atom Ti–O and Pb–O which play very important roles on ferroelectricity of the PbTiO₃/SrTiO₃ superlattices. Comparing to the corresponding paraelectric phase, we find the electrons of the PT (PbTiO₃) layers occupy lower energy states and electrons of the ST (SrTiO₃) layer occupy higher energy states. It is shown that the polarizations of the superlattices decrease with proportion of SrTiO₃ increasing. The constant polarization of local layer indicates that PST superlattices with small modulation lengthen can be approximately considered as a single ferroelectric material. Furthermore, according to electrostatic model, we find that directions of internal electric fields in PT and ST layers are opposite. In PST superlattices, internal electric field in PT layer leads to the loss of polarization of this layer, but the polarization of ST layer is induced by internal electric field of this layer. Compared to the value of the polarization in bulk PbTiO₃, polarization of PST is smaller.     

Design and evaluation of an active electromechanical wheel suspension system

This paper presents an electromechanical wheel suspension, where the upper arm of the suspension has been provided with an electric levelling and a damper actuator, both are allowed to work in a fully active mode. A control structure for the proposed suspension is described. The complex design task involving the control of the electric damper and its machine parameters is tackled by genetic optimisation. During this process, these parameters are optimised to keep the power dissipation of the electric damper as low as possible, while maintaining acceptable comfort and road-holding capabilities. The results of the evaluations carried out demonstrate that the proposed suspension can easily adopt its control parameters to obtain a better compromise of performance than that offered by passive suspensions. If the vehicle is to maintain acceptable performance during severe driving conditions, the damper has to be unrealistically large. However, if the electric damper is combined with a hydraulic damper, the size of the electric damper is significantly reduced. In addition, the design of the electric damper with the suggested control structure, including how it regenerates energy, is discussed.     

Relation between microstructure, properties and spark plasma sintering (SPS) parameters of pure ultrafine WC powder

A combined experimental/numerical methodology is developed to fully consolidate pure ultrafine WC powder under a current-control mode. Three applied currents, 1900, 2100 and 2700 A, and a constant pressure of 20 MPa were employed as process conditions. The developed spark plasma sintering (SPS) finite-element model includes a moving-mesh technique to account for the contact resistance change due to sintering shrinkage and punch sliding. The effects of the heating rate on the microstructure and hardness were investigated in detail along the sample radius from both experimental and modeling points of view. The maximum hardness (2700 HV10) was achieved for a current of 1900 A at the core sample, while the maximum densification was achieved for 2100 and 2700 A. A direct relationship between the compact microstructure and both the sintering temperature and the heating rate was established.     

电熨斗底板水溶性聚四氟乙稀真空静电喷涂工艺

介绍了电熨斗底板真空静电喷涂的工作原理。说明了电晕放电在底板真空静电喷涂中的作用。分析了氟涂料微粒的带电过程及影响因素。这个工艺对产品质量提高的作用进行了分析。