复杂膨胀性围岩条件下交岔点支护技术研究

针对复杂膨胀性围岩条件下交岔点高应力集中区围岩稳定性控制和支护技术难题，通过对交岔点围岩变形表现形式、交岔点围岩变形机理的研究分析，提出了交岔点支护难点及重点。基于围岩控制理论分析，提出了“有限让压的柔性支护+全断面封闭抗压的刚性支护技术”，前期柔性支护采用“高强、高预应力锚杆+锚索+喷浆”联合支护有限度控制围岩变形，允许围岩在可控范围内释放围岩应力|后期通过架设异形支架与支撑架组成的联合支护体并喷射混凝土对交岔点围岩进行全断面封闭抗压支护，有效控制巷道交岔点围岩的变形。确保了交岔点围岩变形的整体可控性、稳定性，达到了预期支护效果。     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

Study on metamerism degree evaluation based on wavelength sensitive cone weighting algorithm

Metamerism phenomenon can be used in illuminant detection to ensure the accuracy of light source. A method based on Long‐, Middle‐, Short‐ wavelength cones(LMS) weighting algorithm to evaluate metamerism degree is proposed. The chromatic relationship between the degree of metamerism mismatch and the light source is studied. Herein, the consistency between the metameric indices (MIs) and CIE1976 L*a*b* color difference ranking is analyzed by SRCC, KRCC, PLCC and RMSE. A statistically sampling method to obtain practical LMS cone fundamentals to evaluate metamerism degree is employed. The analysis results obtained show that the method based on LMS weighting algorithm has good evaluation ability and stability in simulation experiments and statistically sampling experiments, which are in line with visual characteristics of human. Proposed method meets the requirements of selecting metameric pairs used in light source detection. The analysis results have certain guiding significance.     

前和煤业东胶带运输大巷钻孔卸压围岩控制技术

为有效解决前和煤业3#煤层东胶带大巷在原有锚网索支护下围岩变形量大的问题,结合巷道变形特征,确定采用钻孔卸压技术,采用理论分析和数值模拟的方式确定卸压钻孔在修巷作业前,垂直于巷帮打设,钻孔深度为8 m,结合巷道的具体条件确定巷道采用卸压钻孔+让压支护的围岩控制方案,并采用矿压监测验证支护效果。结果表明:支护方案实施后,顶底板和两帮的最大移近量分别为141 mm和132 mm,有效解决了巷道两帮及底板鼓起量大的问题,保证了巷道围岩的稳定性。     

煤矿冲击矿压预测和防治技术浅析

结合镇城底煤矿22605工作面的地质情况和矿压情况,提出了煤炭生产中冲击矿压的预测和防治措施。通过对22605工作面的地质情况和监测数据分析处理并探究了该工作面矿压显现规律,为其设计了一套适合本工作面的冲击矿压监测和防治体系。防治体系有预防和临时解危双重防治措施,从这两方面考虑可以做到全面防治冲击矿压。该体系可以实现矿井的安全生产,保证工作人员的安全。另通过分析冲击矿压发生的基本原理和监测到的数据,建立煤矿冲击矿压防治体系,能够及时有效地将蕴含在煤体中的冲击矿压释放和消除,达到安全生产的目的。     

An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

The effect of optimized carbon source on the synthesis and composition of exopolysaccharides produced by Lactobacillus paracasei

This study aimed to predict the optimal carbon source for higher production of exopolysaccharides (EPS) by Lactobacillus paracasei TD 062, and to evaluate the effect of this carbon source on the production and monosaccharide composition of EPS. We evaluated the EPS production capacity of 20 strains of L. paracasei under the same conditions. We further investigated L. paracasei TD 062, which showed the highest EPS-producing activity (0.609 g/L), by examining the associated biosynthesis pathways for EPS. Genomics revealed that fructose, mannose, trehalose, glucose, galactose, and lactose were carbon sources that L. paracasei TD 062 could use to produce EPS. We identified an EPS synthesis gene cluster that could participate in transport, export, and sugar chain synthesis, and generate 6 sugar nucleotides. Experimental results showed that the sugar content of the EPS produced using fermentation with the optimized carbon source (fructose, mannose, trehalose, glucose, galactose, and lactose) increased by 115%. Furthermore, use of the optimized carbon source changed the monosaccharide content of the associated EPS. The results of enzyme activity measurements showed significant increases in the activity of 2 key enzymes involved in the glycoside synthesis pathway. Our study revealed that optimizing the carbon source provided for fermentation not only increased the production of EPS, but also affected the composition of the monosaccharides by increasing enzyme activity in the underlying synthesis pathways, suggesting an important role for carbon source in the production of EPS by L. paracasei TD 062.     

The growth of oleaginous Rhodotorula glutinis in an internal-loop airlift bioreactor by using mixture substrates of rice straw hydrolysate and crude glycerol

The conversion of lignocellulosic biomass (LCB) to microbial oils is attracting a growing amount of attention. However, the growth of the oleaginous yeast Rhodotorula glutinis on LCB hydrolysate (mainly rice straw) only will lead to a low lipid mass fraction, in the range of 10–20%. This study shows that the addition of crude glycerol to the LCB hydrolysate medium can efficiently raise the lipid mass fraction to the range of 30–40%. Crude glycerol is a by-product in the biodiesel production process. The use of renewable LCB hydrolysate and crude glycerol would greatly reduce the substrate cost for microbial oil production using R. glutinis. In addition, the results of experiments show that a low-cost airlift bioreactor is a more suitable fermentation process for the growth of R. glutinis than the use of a conventional agitation tank. When using mixed carbon sources of LCB hydrolysate with 30 kg m⁻³ of reducing sugars and 30 kg m⁻³ of crude glycerol, a maximal cell mass of 21.4 kg m⁻³ and lipid mass fraction of 58.5 ± 6.2 were achieved in an internal loop airlift bioreactor, and this process may have the potential to be applied in scale-up production.     

煤田地震勘探中多井组合爆炸法浅析

地震勘探中炸药作为激发震源的激发条件多样,采用有效的震源激发方式,才能取得高信噪比的地震原始数据。本文依据有关爆破原理,理论结合实践经验,提出在厚黄土区采用多井组合的激发方式,能有效压制噪声,增强性噪比,提高数据质量。