Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Low concentration short time ozonation of rapeseed seeds reduces the stability of the oil and content of some antioxidant components

Ozonation is an innovative way to preserve high quality of seed during storage and it is an alternative to harmful organophosphorus agents. Disclosure of changes in the rapeseed oil under the influence of oxidative action of ozone on the seeds was the aim of the work and is presented for the first time. Two ozone concentrations and different length of ozonation were applied. The changes in tocopherols, phenolics, flavonoids contents, antiradical activity and oxidative stability were examined. The average vitamin E concentration was 33 mg per 100 g of oil before and 31.7 after ozonation of seeds. The average content of phenolic compounds was 14.3 mg of sinapic acid g⁻¹ and 16.9 after the ozone treatment. Changes in the flavonoids content and antioxidant activity were observed too. Ozonation caused a decrease in the vitamin E concentration which resulted also in reducing the quenching of free radicals and reduction of oil induction time.     

Solidification morphology and phase selection in drop-tube processed Ni–Fe–Si intermetallics

Drop-tube processing was used to rapidly solidify droplets of Ni_64.7Fe₁₀Si_25.3 and Ni_59.7Fe₁₅Si_25.3 alloys. In the larger droplets, and therefore at low cooling rates, only two phases, γ-Ni₃₁Si₁₂ and β₁-Ni₃Si were observed. Conversely, in the smaller droplets, and therefore at higher cooling rates, the metastable phase Ni₂₅Si₉ was also observed. The critical cooling rate for the formation of Ni₂₅Si₉ was estimated as 5 × 10³ K s⁻¹. SEM and TEM analysis reveals three typical microstructures: (I) a regular structure, comprising single-phase γ-Ni₃₁Si₁₂ and a eutectic structure between γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (II) a refined lamellar structure with a lamellar spacing <50 nm comprising γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (III) an anomalous structure with a matrix of Ni₂₅Si₉ and only a very small proportion of a second, and as yet unidentified, phase. These results indicate that there is an extended stability field for Ni₂₅Si₉ in the Ni-rich part of the Ni–Fe–Si ternary system in comparison to the Ni–Si binary system. With an increase of cooling rate, an increasing fraction of small droplets experience high undercoolings and, therefore, can be undercooled into the Ni₂₅Si₉ stability field forming droplets consisting of only the anomalous structure (III). The Fe atoms are found to occupy different substitutional sites in different phase, i.e. Fe substitutes for Ni in the γ phase and Si in the L1₂ (β₁) phase respectively.     

Static stress analysis of carbon nano-tube reinforced composite (CNTRC) cylinder under non-axisymmetric thermo-mechanical loads and uniform electro-magnetic fields

Static stresses analysis of carbon nano-tube reinforced composite (CNTRC) cylinder made of poly-vinylidene fluoride (PVDF) is investigated in this study. Non-axisymmetric thermo-mechanical loads are applied on cylinder in presence of uniform longitudinal magnetic field and radial electric field. The surrounded elastic medium is modeled by Pasternak foundation because of its advantages to the Winkler type. Distribution of radial, circumferential and effective stresses, temperature field and electric displacements in CNTRC cylinder are determined based on Mori–Tanaka theory. The detailed parametric study is conducted, focusing on the remarkable effects of magnetic field intensity, elastic medium, angle orientation and volume fraction of carbon nano-tubes (CNTs) on distribution of effective stress. Results demonstrated that fatigue life of CNTRC cylinder will be significantly dependent on magnetic intensity, angle orientation and volume fraction of CNTs. Results of this research can be used for optimum design of thick-walled cylinders under multi-physical fields.     

面向消费类电子产品的自动化生产线成组技术

针对现代消费类电子产品快速更新换代的现状, 介绍了该类产品的自动化生产线成组技术,阐述了通过度量消费类电子产品相似性和派生性特征,对产线进行成组编码的原理,研究产线工位单元的建模方法,描述了建模内容,并通过有无装载板的产线结构,论述了产线成组编码集成的途径和方法.     

Hygrothermal deformation of orthotropic nanoplates based on the state-space concept

This paper deals with the investigation of the effect of hygrothermal conditions on the bending of nanoplates using Levy type solution model employing the state-space concept. The nanoplates are assumed to be subjected to a hygrothermal environment. The two-unknown function plate theory is used to derive the governing differential equations on the basis of Eringen's nonlocal elasticity theory. The governing equations contain the small scale effect as well as hygrothermal and mechanical effects. These equations are converted into a set of first-order linear ordinary differential equations with constant coefficients. Analytical solution of bending response for nanoplates under combinations of simply supported, clamped and free boundary conditions is obtained. Comparison of the results with those being in the open literature is made. The influences played by small scale parameter, temperature rise, the degree of moisture concentration, boundary conditions, plate aspect ratio and side-to-thickness ratio are studied.     

高分散度Pt/C电催化剂的制备

Cabot公司Vulcan XC-72型炭黑，经过H2O2氧化处理后作为Pt的载体，H2PtCl6作为金属前驱体制备了高度分散的Pt/C催化剂。讨论了不同条件下H2PtCl6在炭黑上的吸附性能。载体经过H2O2氧化处理24h,H2PtCl6在pH=9下吸收48h，H2 350℃还原2h，可以制备出铂晶粒平均大小为1.8nm的Pt/C电催化剂。     

DS90C363/DS90CF364 LVDS发送/接收器在数字RGB液晶屏上的应用

通过在FPD铁路上使用LVDS技术可使具有数字RGB接口的液晶显示屏的工作距离大大增加。文章通过一个具体应用环境介绍了21位LVDS发送器/接收器DS90C363/DS90CF364传输套片的主要特性、引脚功能、工作原理，同时指出了在具体设计使用时的注意事项。