酸改性CoPd/TiO2催化CH4-CO2直接合成C2含氧化合物

采用酸处理方法对CoPd/TiO₂催化剂进行改性，并将酸改性催化剂用于温和条件下CH₄-CO₂梯阶转化直接合成C₂含氧化合物（乙酸和乙醇）的反应。在150～300℃考察了浸酸方式和不同种类酸处理对催化剂活性和选择性的影响。采用X射线衍射（XRD）、X射线光电子能谱（XPS）、NH₃程序升温脱附（NH₃-TPD）和N₂吸附对催化剂进行了表征。结果表明，酸改性明显提高了CoPd/TiO₂上C₂含氧化合物的生成速率和选择性。浸酸方式对催化剂性能和结构有显著影响，先用酸浸渍载体然后再浸渍活性金属所得催化剂具有更高的活性。在H₃PO₄、HNO₃和HCl中，H₃PO₄浸渍的催化剂活性最佳，在150℃时C₂含氧化合物（乙酸和乙醇）的生成速率为3365 μg/(g·h)，选择性达到91%。     

Digital image correlation strain measurement of thick adherend shear test specimen joined with an epoxy film adhesive

Structural bonding and bonded repairs of composite materials become more and more important. Understanding the strain within the bondline leads to suitable bonding design. For new design approaches the strain distribution within the bondline has to be analyzed. Thus, often finite element analysis (FE) are used. However, a huge challenge is the availability of reliable material properties for the adhesives and their validation. Previous work has shown that it is possible to measure the small displacements resulting within thin epoxy film adhesives using high resolution digital image correlation (DIC). In this work a 2D DIC setup with a high resolution consumer camera is used to visualize the strain distribution within the bondline over the length of the joint as well as over the adhesive thickness. Therefore, single lap joints with thick aluminum adherends according to ASTM D 5656 are manufactured and tested. Local 2D DIC strain measurements are performed and analyzed. Two different camera setups are used and compared. The evaluation provides reliable material data and enables a look insight the bondline. The results of the full field strain data measured with DIC are compared with numerical simulations. Thus, material models as well as chosen parameters for the adhesive are validated. Compared to extensometers, giving only point-wise information for fixed measuring points, the DIC allows a virtual point-wise inspection along the complete bondline. Furthermore, it allows measuring close to the bondline to reduce the influence of adherend deformation.     

Influence of Bridgman solidification on microstructures and magnetic behaviors of a non-equiatomic FeCoNiAlSi high-entropy alloy

The non-equiatomic FeCoNiAlSi alloy is prepared by the Bridgman solidification (BS) technique at different withdrawal velocities (V = 30, 100, and 200 μm/s). Various characterization techniques have been used to study the microstructure and crystal orientation. The morphological evolutions accompanying the crystal growth of the alloy prepared at different withdrawal velocities are nearly the same, from equiaxed grains to columnar crystals. The transition of coercivity is closely related to the local microstructure, while the saturation magnetization changes little at different sites. The coercivity can be significantly reduced from the equiaxed grain area to the columnar crystal area when the applied magnetic field direction is parallel to the crystal growth direction, no matter what is the withdrawal velocity. In addition, the alloy possesses magnetic anisotropy when the applied magnetic field is in different directions.     

Neutral axis depth and moment redistribution in FRP and steel reinforced concrete continuous beams

The neutral axis depth is considered the best parameter for quantifying the moment redistribution in continuous concrete beams, as exemplified in various design codes worldwide. It is therefore important to well understand the variation of neutral axis depth against moment redistribution. This paper describes a theoretical investigation into the neutral axis depth and moment redistribution in concrete beams reinforced with fibre reinforced polymer (FRP) and steel bars. A finite element model has been developed. The model predictions are in favourable agreement with experimental results. Three types of reinforcement are considered, namely, glass fibre, carbon fibre and steel. Various levels of reinforcement ratio are used for a parametric evaluation. The results indicate that FRP reinforced concrete continuous beams exhibit significantly different response characteristics regarding the moment redistribution and variation of neutral axis depth from those of steel reinforced ones. In addition, it is found that the code recommendations are generally unsafe for calculating the permissible moment redistribution in FRP reinforced concrete beams, but the neglect of redistribution in such beams may be overconservative.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Collapse load of composite laminates: Lower bound evaluation by stress field analytical approximation

The paper proposes a limit analysis approach to define the ultimate load capacity of orthotropic composite laminates under biaxial loading and plane stress conditions. A lower bound to the collapse load multiplier is computed by solving a maximization nonlinear problem, according to the static theorem of limit analysis. To set up the optimization problem a stress field distribution is hypothesized at lamina level, moreover inter-lamina stresses are also considered. The effectiveness and validity of the proposed approach is shown by comparing the obtained numerical predictions both with available experimental data and with other numerical results carried out by means of a different numerical lower bound approach.     

Influence of internally dropped-off plies on the impact damage of asymmetrically tapered laminated CFRP

This paper presents an experimental study of low velocity impact response of carbon/epoxy asymmetrically tapered laminates. The tests are realised at energy between 10 and 30 J on two types of layup with multiple terminated plies. The type and localisation of damage are analysed using C-scan and micrographs. Then, the data is compared with the response of corresponding respective plain laminate. The effects of some tapering parameters (taper angle, drop-off disposition and configuration) on the impact damage mechanisms are also investigated. Very similar impact damage phenomena are found between tapered and plain laminates. The presence of material discontinuity due to the resin pocket affects less the damage mechanism than the structural difference between the thick and the thin sections.     

Facile growth of novel morphology correlated Ag/Co-doped ZnO nanowire/flake-like composites for superior photoelectrochemical water splitting activity

In this paper, novel morphology correlation between silver nanowires (AgNWs) and cobalt (Co)-doped ZnO (Co-ZnO) flake-like thin films (nanowire/flake-like) has been proposed for enhanced photoelectrochemical (PEC) water splitting activity. Here in, high-quality AgNWs/Co-ZnO heterostructures enabled superior visible light water splitting activity compared to the pure ZnO and AgNWs/ZnO. To address the strategic effect of AgNWs coupling and transition metal (Co-2?at%) doping into the ZnO host lattice, we have carried out the X-ray diffraction, field emission scanning microscopy, X-ray photoelectron spectroscopy, UV–Vis transmittance, water contact angle and PEC analyses. In this way, PEC water splitting activity was mainly examined by linear sweep voltammetry (I-V), amperometric I-t and photoconversion efficiency (η) studies. The experimental results provide clear evidence of morphology correlation between AgNWs and Co-ZnO flake-like structures for strong visible light absorption. Specifically, AgNWs/Co-ZnO composites exhibited significant enhancement in the photocurrent density (7.0?×?10^?4 A/cm²) than AgNWs/ZnO (3.2?×?10^?4 A/cm²) and pure ZnO (1.5?×?10^?6 A/cm²). As a result, detailed AgNWs/Co-ZnO geometry has great potential for photoconversion efficiency (0.73%). In a word, the merits of controllable AgNWs/Co-ZnO heterostructure are proposed to improve the visible light harvesting and charge carrier generation for energy conversion devices.     

Homogenization with uncertainty in Poisson ratio for polymers with rubber particles

The main aim of this work is dual computer analysis of probabilistic coefficients for the homogenized tensor of the polymer filled with the rubber particles having randomized Poisson ratios of both constituents. The major issue is to verify an influence of a randomness in rubber Poisson ratio close to the compressibility limit on the uncertainty of the effective tensor probabilistic characteristics. Probabilistic analysis presented here is carried out using mainly the stochastic perturbation technique provided by the common application of the traditional FEM commercial code ABAQUS and the symbolic computations package MAPLE. This FEM-based technique employs polynomial response function of the optimum order recovered from the weighted least squares method and following a set of deterministic solutions obtained for various values of the randomized input parameter. Optimization procedure is released entirely into a symbolic environment, where maximization of the correlation factor together with minimization of the fitting variance and approximation error are applied. Homogenization technique consists in equating of deformation energies for the real composite and the artificial one characterized by the effective elasticity tensor with uncertainty.