A source apportioned mercury mass balance across a coal-based petrochemical complex

Coal-fired power generation facilities are the largest single anthropogenic source of mercury to the atmosphere. Global mapping of anthropogenic emissions has previously estimated the mercury emission from stationary combustion from South Africa at being 82.6 tonnes per annum, but preliminary in-house calculations have placed this at a significantly lower amount. A petrochemical facility in South Africa, utilising a significant amount of coal in its gasification and steam generation processes, undertook a project to determine a mercury mass balance across the complex, and to apportion the Hg emissions from the facility.     

Investigation on interior moisture distribution inducing dielectric anisotropy of coals

Dielectric anisotropy phenomenon of coal was detectable by many dielectric measurements. The paper presented that it was attributed to coal interior moisture distribution. A new model describing interior moisture distribution was developed basing on microstructure observation of coal. In the model, coal interior moisture distribution was analyzed and simulated numerically, the relationship between interior moisture distribution and coal dielectric property was constructed, the character of the permittivity varying with moisture content had also been studied and coal dielectric anisotropy was deduced. Corresponding experiment results were well satisfied with the model analysis, demonstrating that the interior moisture content could cause coal dielectric anisotropy.     

Study of the effect of ultrasonic treatment on the surface composition and the flotation performance of high-sulfur coal

This paper highlighted the use of X-ray diffraction, scanning electron microscopy and X-ray fluorescence spectroscopy to investigate the changes on the surface composition of high-sulfur coal and pyrite before and after ultrasonic conditioning. The results showed that ultrasonic conditioning resulted in a decrease in the contents of iron and sulfur in coal, an increase in the content of element carbon, and an increase in the purity of the coal. Conversely, ultrasonic conditioning led to an increase in the content of iron and sulfur in pyrite, a decrease in the impure content of calcium, and a relative increase in the purity of the pyrite after ultrasonic conditioning. This study verified that on the one hand, ultrasonic conditioning can promote the pyrite separation from the high-sulfur coal, with the separated pyrite taking the form of FeS; on the other hand, it can produce a cleaning effect on the surface of coal and pyrite with the consequent increase both in hydrophobicity of coal and hydrophilicity of pyrite. The paper introduced ultrasonic pre-treatment of the slurry and stepped froth removal tests of high-sulfur coal and the study on the yield, ash and sulfur content of clean coal in different phases. The results gave further evidence of the increases both in the rate and the selectivity of flotation. This study shows that ultrasonic conditioning can enhance the performance of de-sulphurization of high-sulfur coal flotation.     

测尘仪原理与应用

本文介绍了测尘仪器的基本原理,着重阐述了透射法和散射法的基本原理和实际应用.     

FAST MEASUREMENT OF ASH CONTENT IN COAL WASHING PLANT

The coal filter cake is a product of fine coal after floatation which has an ash content of 7-13%, water content of 30±2%, and a particle size of less than 1 mm. The ash content was measured by the intensity of the single backscattered gamma-ray, and its accuracy is mainly dependent on the energy of the gamma-ray. The 238Pu low energy photon source is selected in this work. The energy of its gamma-ray is 15 keV, which can result not only in the best sensitivity, but also in the lowest contribution to the environment radiation. The root mean square deviation of the ash measurement is±0.33% (±1σ).     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

变频器在链条炉系统中的应用

本文介绍了链条炉的定义，链条炉应用变频调速的意义，链条炉控制系统的原理，锅炉采用变频调速控制的优点，变频调速的控制方法和逻辑，链条炉采用变频调速装置的节能分析。     

CONDITIONING COAL GAS WITH REFRIGERATED METHANOL IN A SYSTEM OF PACKED COLUMNS

Experience with the operation of a pilot-scale unit is used to outline potential difficulties in the operation of acid gas removal systems on gases produced from coal. The pilot plant has been used to condition gases produced from subbituminous coal, devolatilized char, peat and lignite. The solvent used in the acid gas removal system has been refrigerated methyl alcohol. Data from this study document accumulation of hydrocarbons, sulfur and nitrogen compounds, and mercury in the circulating solvent.     

焦炉烘炉问题探讨

介绍了柳钢焦化厂6、7号焦炉烘炉中存在的问题及其改进措施。     

Numerical analysis for the prediction of bump prone conditions:A southern Appalachian pillar coal bump case study

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry,and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism is not clearly understood. In this case history, a cut-by-cut analysis of retreat mining operations was conducted on the 4 East Main leading up to the pillar bump event. Numerical input parameters were derived from site-specific geologic information and mine geometry for the analysis of pillar stress conditions and energy release using LaModel. An overview of stress conditions in the panel was presented including a precursor event that occurred two crosscuts inby the bump site. The methodology presented in the paper for the evaluation of the fatal bump event can be used for the identification of bump prone conditions prior to development and retreat of a mining area.