Q690钢焊接接头微观组织对冷裂纹的影响研究

分析了Q690钢手工电弧焊与气体保护焊焊接冷裂纹产生与微观组织的联系。结果表明: 焊接冷裂纹起源于斜Y坡口根部, 沿熔合区、焊缝扩展至焊缝表面;2种工艺焊接的接头组织硬度均较母材高, 而塑性较差。热影响区为马氏体、贝氏体与铁素体混合组织, 焊缝组织由先共析铁素体、侧板条铁素体、贝氏体和针状铁素体等组成, 针状铁素体抗裂纹扩展能力较其他组织强。在2种焊接方法对应断口中观察到了冷裂纹起裂、扩展与断裂区的不同形貌, 起裂与扩展区存在塑性变形, 而断裂区为解理断裂。     

Changes in phenolics,soluble solids,vitamin C,and antioxidant capacity of various cultivars of hardy kiwifruits during cold storage

Food Science and Biotechnology - Hardy kiwifruits (Actinidia arguta) contain various bioactive compounds such as vitamin C and phenolics and can withstand cold temperatures. Changes in soluble...     

β-环糊精修饰Ni/SFCC强化C9石油树脂催化加氢性能

以废弃的流化催化裂化催化剂（简称SFCC）为载体、β-环糊精为金属络合剂、硝酸镍为镍源，采用湿法浸渍法制备β-环糊精修饰的Ni/SFCC催化剂（简称Ni/SFCC-CD催化剂），考察其对C9石油树脂的催化加氢性能。通过BET比表面积测试、H2程序升温还原、X射线光电子能谱等手段对催化剂的物相结构进行表征，研究β-环糊精的作用机理及其对催化剂加氢性能的影响。研究结果表明：在反应温度为260 ℃、反应压力为7 MPa、反应时间为2.0 h的最优条件下，采用Ni/SFCC-CD催化C9石油树脂加氢，可制得溴值为1.45 gBr/（100 g）、色号（加纳德）小于1的水白色氢化C9石油树脂，催化剂循环使用4次后仍保持良好活性；β-环糊精的作用机理是：β-环糊精与硝酸镍产生络合作用，抑制硝酸镍的分解、控制NiO的结晶过程和增强活性组分Ni与载体之间的相互作用力，从而提高了Ni/SFCC-CD的催化活性和稳定性。     

Microwave and conventional treatment of low-cement high-alumina castables with different water-to-cement ratio; Part II. Dehydration

Modern refractory castables contain between 3.5 and 5?wt.-% water that is necessary for sufficient flow during emplacement and for the formation of hydrate phases, necessary for the green strength of the material. Prior to the high temperature use of this material, it must be dried very carefully to avoid explosive spalling.This paper will demonstrate that beside conventional drying of pre-shaped materials in resistance furnaces microwave radiation is an energy saving and rapid method to remove pore water as well as hydrate bond water from the castable. In comparison to resistance furnaces, the use of microwave radiation does not affect the castable properties as there are mechanical strength (MOR, CCS), open porosity and pore size distribution. This study proved microwave radiation as valuable alternative with a series of tabular alumina based low cement castables (LLC) in which the water-to-cement-ratio (wcr = 0.64, 0.75, 0.82 and 1.13) was systematically altered by changing the cement concentration at constant mixing water concentration of 4.5%.     

Hydrogen production through dry reforming of biogas using a porous electrochemical cell: Effects of a cobalt catalyst in the electrode and mixing of air with biogas

This paper reports the performance of porous Gd-doped ceria (GDC) electrochemical cells with Co metal in both electrodes (cell No. 1) and with Ni metal in the cathode and Co metal in the anode (cell No. 2) for CO₂ decomposition, CH₄ decomposition, and the dry reforming reaction of a biogas with CO₂ gas (CH₄ + CO₂ → 2H₂ + 2CO) or with O₂ gas in air (3CH₄ +?1.875CO₂ +?1.314O₂ → 6H₂ +?4.875CO +?0.7515O₂). GDC cell No. 1 produced H₂ gas at formation rates of 0.055 and 0.33?mL-H₂/(min?m²-electrode) per 1?mL-supplied gas/(min?m²-electrode) at 600?°C and 800?°C, respectively, by the reforming of the biogas with CO₂ gas. Similarly, cell No. 2 produced H₂ gas at formation rates of 0.40?mL-H₂/(min?m²) per 1?mL-supplied gas/(min?m²) at 800?°C from a mixture of biogas and CO₂ gas. The dry reforming of a real biogas with CO₂ or O₂ gas at 800?°C proceeded thermodynamically over the Co or Ni metal catalyst in the cathode of the porous GDC cell. Faraday's law controlled the dry reforming rate of the biogas at 600?°C in cell No. 2. This paper also clarifies the influence of carbon deposition, which originates from CH₄ pyrolysis (CH₄ → C + 2H₂) and disproportionation of CO gas (2CO → C + CO₂), on the cell performance during dry reforming. The dry reforming of a biogas with O₂ molecules from air exhibits high durability because of the oxidation of the deposited carbon by supplied air.     

Biomineralization,strength and cytocompatibility improvement of bredigite scaffolds through doping/coating

Coprecipitation-derived, sacrificial polymeric (urethane) foam-fabricated bredigite (Ca₇MgSi₄O₁₆) scaffolds were processed by individual and combined treatments of fluoride doping and poly (lactic-co-glycolic acid) (PLGA) coating and then studied in terms of structure, mechanical strength, bioactivity and cell biocompatibility in vitro. According to scanning electron microscopy and Archimedes porosimetry, the geometrical characteristics of pores for all the scaffolds are in the appropriate range for hard tissue regeneration applications. The apatite-formation ability of the samples immersed in a simulated body fluid is improved by doping for both the bare and coated conditions, based on microscopic and energy-dispersive X-ray spectroscopic analyses. Both the treatments advantageously buffer physiological pH changes imposed due to the fast bioresorption of the ceramic. Also, the biodegradable PLGA coating typically enhances the compressive strength of the scaffolds, which is critical for bone tissue engineering. In accordance with the MTT assay on osteoblast-like cells (MG-63) cultures, both the processes individually enhance the cell viability, while the highest improvement is obtained for the combined application of them. It is finally concluded that fluoride doping and PLGA coating are impressive approaches to improve the bioperformance of bredigite-based scaffolds.     

Assessment of the effectiveness of steel fibre reinforcement for the punching resistance of flat slabs by experimental research and design approach

The present paper deals with the experimental assessment of the effectiveness of steel fibre reinforcement in terms of punching resistance of centrically loaded flat slabs, and to the development of an analytical model capable of predicting the punching behaviour of this type of structures. For this purpose, eight slabs of 2550 × 2550 × 150 mm³ dimensions were tested up to failure, by investigating the influence of the content of steel fibres (0, 60, 75 and 90 kg/m³) and concrete strength class (50 and 70 MPa). Two reference slabs without fibre reinforcement, one for each concrete strength class, and one slab for each fibre content and each strength class compose the experimental program. All slabs were flexurally reinforced with a grid of ribbed steel bars in a percentage to assure punching failure mode for the reference slabs. Hooked ends steel fibres provided the unique shear reinforcement. The results have revealed that steel fibres are very effective in converting brittle punching failure into ductile flexural failure, by increasing both the ultimate load and deflection, as long as adequate fibre reinforcement is assured. An analytical model was developed based on the most recent concepts proposed by the fib Mode Code 2010 for predicting the punching resistance of flat slabs and for the characterization of the behaviour of fibre reinforced concrete. The most refined version of this model was capable of predicting the punching resistance of the tested slabs with excellent accuracy and coefficient of variation of about 5%.     

Accuracy of wind energy forecasts in Great Britain and prospects for improvement

The metric representing the wind energy forecast error, when reported as a percent, is calculated quite differently than the error metrics for electricity transmission, electricity load, or in other industries such as manufacturing when they are also reported as a percent. The resulting calculated metric is quite different from what would be reported if the method utilized elsewhere was employed. This paper examines the possible forecast assessment and operational challenges associated with this finding. Concerning the prospects for improvement, the errors reported in MW of energy have a systematic component. With this insight, we developed a model to improve accuracy.     

Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.