Neutral electrolyte aluminum air battery with open configuration

A kind of new long life aluminum air batteries with open configuration was developed, using aluminum alloy doped with Ga, In, Sn, Bi, Pb and Mn as anode, NaCl solution as electrolyte and air electrode as cathode. The polarization curves of aluminum electrode and air electrode were tested. And the cell's performance was tested to calculate the utilization of aluminum electrode and the energy density. It is shown that, in the 3.5% NaCl solution, the cell can discharge at 0.29 A for 140 h with the working voltage keeping over 1.1 V. The utilization ratio of aluminum anode is over 44%, and the life of battery is longer than 2400 h.     

New attachment for controlling gas flow in the HVOF process

During the decade, the high-velocity oxyfuel (HVOF) process proved to be a technological alternative to the many conventional thermal spray processes. It would be very advantageous to design a nozzle that provides improved performance in the areas of deposition efficiency, particle in-flight oxidation, and flexibility to allow deposition of ceramic coatings. Based on a numerical analysis, a new attachment to a standard HVOF torch was modeled, designed, tested, and used to produce thermal spray coatings according to the industrial needs mentioned above. Performance of the attachment was investigated by spraying several coating materials including metal and ceramic powders. Particle conditions and spatial distribution, as well as gas phase composition, corresponding to the new attachment and the standard HVOF gun, were compared. The attachment provides better particle spatial distribution, combined with higher particle velocity and temperature. The original version of this article was published as part of the ASM Proceedings, Thermal Spray 2003: Advancing the Science and Applying the Technology, International Thermal Spray Conference (Orlando, FL), 5–8 May, 2003, Basil R. Marple and Christian Moreau, Ed., ASM International, 2003.     

Deformation behaviour and oxidation resistance of single-phase and two-phase L21-ordered Fe–Al–Ti alloys

Single-phase Fe–Al–Ti alloys with the Heusler-type L2₁ structure and two-phase L2₁ Fe–Al–Ti alloys with MgZn₂-type Laves phase or Mn₂₃Th₆-type τ₂ phase precipitates were studied with respect to hardness at room temperature, compressive 0.2% yield stress at 20–1100 °C, brittle-to-ductile transition temperature (BDTT), creep resistance at 800 and 1000 °C and oxidation resistance at 20–1000 °C. At high temperatures the L2₁ Fe–Al–Ti alloys show considerable strength and creep resistance which are superior to other iron aluminide alloys. Alloys with not too high Ti and Al contents exhibit a yield stress anomaly with a maximum at temperatures as high as 750 °C. BDTT ranges between 675 and 900 °C. Oxidation at 900 °C is controlled by parabolic scale growth.     

SCR式弧焊整流电源CAD系统研究

对ＳＣＲ式弧焊整流电源的计算机辅助设计系统进行了研究,简称“ＳＣＲＡＷＳＣＡＤ”。结果表明利用该系统对ＳＣＲ式整电源进行研究,不仅提高了设计精度与速度,而且与也减轻了设计者的劳动强度及降低设计成本。同时,该系统具有功能齐全,操作方便,通用性广的特点。在弧焊电源的研究、设计与制造方面具有广阔前景。     

应用统计学实验方法优化铜常温发黑剂配方

运用统计学试验设计方法研究了不同的因素对铜常温发黑剂体系的性能影响.通过试验结果的统计分析,揭示了这些因素对体系的多种显著影响.更为重要的是本研究发现了多种因素间的双因素交互作用.而且这些交互作用的影响很难被传统的单因素试验发现.本研究结果可用于设计高性能的铜常温发黑剂.     

变质处理高速钢导辊的研究

通过调整高速钢成分和采用RE—K—Na复合变质处理；改变了共晶碳化物的形态和分布，使铸造高速钢冲击韧度提高69．9％，热疲劳抗力也明显改善。变质处理高速钢导辊使用中不粘钢、不破碎、不剥落，使用寿命比高镍铬合金铸钢和Crl2MoV锻钢导辊提高2—3倍。     

基于介电泳效应的高速抛光电极分布仿真研究与实验验证

目的解决传统平面环抛过程中存在的两种问题:(1)抛光液受抛光盘和工件旋转离心力作用而抛光液在加工区域分布不均,导致加工工件高平面度差;(2)抛光液受到的离心力作用限制了抛光盘转速,导致抛光效率低。方法提出一种基于介电泳效应的平面抛光方法(DEPP),在抛光区域增加一个非均匀电场,利用中性粒子在非均匀电场中极化后受介电泳力的作用,使其具有向电极和抛光区域中心运动的现象,降低旋转离心力对抛光液的甩出作用,实现对平面工件的高速、高精度抛光。采用有限元分析软件数值模拟极化后磨粒所受介电泳力对离心力的抑制作用,优化产生非均匀电场的不同电极宽度,得到最优非均匀电场电极分布参数,实际测量优化电极后抛光液所受介电泳力的大小和方向,最后搭建试验平台验证介电泳效应高速抛光平面工件的有效性。结果提高抛光盘转速,进行抛光磨砂玻璃对比实验,加工1 h以后,采用介电泳效应抛光能完全去除玻璃磨砂层,工件平整度好,最终RMS值为0.276λ;无介电泳效应抛光后,工件中心部分磨砂层仍有存在,工件平整度相对较差,最终RMS值为0.694λ。通过测量加工去除量,介电泳效应抛光比无介电泳效应抛光的去除率提升了18%结论通过仿真模拟和实验验证,证明了调整电极布置形式以及优化电极分布参数后,介电泳效应高速平面抛光的方法能够有效提升抛光效率和抛光后工件表面平面度。     

Effect of directional solidification and heat treatments on the microstructure and mechanical properties of multiphase intermetallic Zr-doped Ni–Al–Cr–Ta–Mo alloy

The effect of directional solidification and heat treatments on the microstructure and mechanical properties of intermetallic Ni–21.29Al–7.04Cr–1.46Ta–0.64Mo–0.57Zr (at.%) alloy was studied. Increasing growth rate is found to decrease primary dendrite arm spacing and to increase volume fraction of β(NiAl)-based dendrites and low melting point γ′(Ni₃Al)/Ni₅Zr eutectic. Room-temperature tensile yield strength and ultimate tensile strength increase and plastic elongation to fracture decreases with the increasing growth rate. Two types of heat treatments of directionally solidified (DS) specimens including two-step ageing at temperatures of 1273 and 1123 K and two-step solution annealing at 1373 and 1493 K were performed. Ageing at 1273 and 1123 K decreases volume fractions of the dendrites and eutectic regions and leads to a coarsening of spherical -Cr and needle-like γ′ precipitates within the β-phase. Annealing at 1373 K for 100 h is shown to be sufficiently long to completely dissolve the eutectic regions. Compressive yield strength increases with increasing temperature reaching a peak value at about 1023 K and then decreases at higher temperatures. Minimum creep rate is found to depend strongly on the applied stress and temperature according to a power law. The power law stress exponent n is determined to be 5.1 and apparent activation for creep Q_a is measured to be 326 kJ/mol.     

高钒高速钢碳化钒形态的数值化分析

针对碳化钒的不同形态,设计出定量分析软件,并利用形状因子K,实现了高钒高速钢不同碳化物形态数值化处理,当K介于0.785～1.000之间碳化钒形态为团球状;K≤0.223,碳化钒呈开花状.高钒高速钢当碳含量达到4.2%时,K为0.86和当量直径D为0.78μm,碳化物呈团球状均匀分布.     

高温运行对镍基异种金属接头力学性能的影响

对12Cr1MoV和0Cr17ni12Mo2两种管材的镍基异种金属接头进行焊后状态和高温运行后状态对比试验。结果表明，高温运行使异种钢接头σ-ε图中曲线移动，反映了高温运行后异种钢接头的屈服强度和塑性有所下降；高温运行使异种钢接头的各项力学性能指标σb,σ0.2,δ5,ψ均略有下降，该结果与接头组织变化及12Cr1MoV钢珠光体组织中碳化物球化倾向等不利因素有关；高温运行对异种钢接头断口部位及宏观断口形貌特征无大的影响；高温运行后异种钢接头拉伸试样仍断在母材处，表明镍基异种钢接头的抗拉强度是比较满意的。