微纳级双极晶体管的热耗散研究

对于双极性晶体管,由于自身存在的自加热现象,严重地影响着器件的特性。基于热电流方程、泊松方程及电流密度方程,在二维器件仿真环境下,进行了微纳级小尺寸npn双极性晶体管热现象的器件物理特性分析。重点研究了器件的集电极电流IC与晶格温度T的因变关系。研究结果显示,随着IC的增加,器件的晶格温度逐渐升高,VCE保持在3.0V、VBE达到最大值0.735V时,随器件晶格温度的升高VBE将减小。最后,笔者给出了描述晶体管温变关系的三维曲线。     

Theory of Seepage into an Auger Hole in a Confined Aquifer Overlying a Gravel Substratum

An analytical solution is presented to the problem of steady groundwater flow seeping into a pumped cylindrical hole partially penetrating a homogeneous and anisotropic confined aquifer overlying a gravel substratum. Solutions are obtained for two general cases of the problem: (1) when the level of the pumped hole is below the confining layer; (2) when it is above it. The validity of the proposed theory is tested by comparing analytical predictions obtained for a few flow situations with corresponding results obtained by numerical means. The theory presented here can be utilized to convert the rate of rise of water in a pumped auger hole into directional conductivities of soil, in areas where water is found to be in a confined state overlying a gravel substratum. The study shows that the conductivity values calculated by neglecting the confining pressure of an artesian aquifer with a gravel base [i.e., by applying the existing (Boast and Kirkham in 1971), auger hole seepage theory for a phreatic aquifer with a gravel base to confined situations] may result in serious error; hence, the artesian head of an aquifer must be accounted for while computing the conductivity values. Further, it is observed that the area contributing flow to a pumped auger hole/well with a gravel base is mostly restricted to a short radial distance from the center of the hole, particularly for situations where the gravel substratum is located close to the bottom of the hole. This is in contrast to auger hole flow situations overlying an impervious substratum, where the domain contributing flow is mostly spread out to a considerable distance from the center of the hole.     

The stiffness matrix in elastically articulated rigid-body systems

Discussed in this paper is the Cartesian stiffness matrix, which recently has received special attention within the robotics research community. Stiffness is a fundamental concept in mechanics; its representation in mechanical systems whose potential energy is describable by a finite set of generalized coordinates takes the form of a square matrix that is known to be, moreover, symmetric and positive-definite or, at least, semi-definite. We attempt to elucidate in this paper the notion of “asymmetric stiffness matrices”. In doing so, we show that to qualify for a stiffness matrix, the matrix should be symmetric and either positive semi-definite or positive-definite. We derive the conditions under which a matrix mapping small-amplitude displacement screws into elastic wrenches fails to be symmetric. From the discussion, it should be apparent that the asymmetric matrix thus derived cannot be, properly speaking, a stiffness matrix. The concept is illustrated with an example.     

桐柏抽水蓄能电站斜井开挖技术

桐柏抽水蓄能电站斜井扩挖在总结以往类似工程施工经验的基础上，对提升系统、信号控制系统及扩挖钻爆等工艺进行了优化，开创了斜井施工的新局面。为我国抽水蓄能电站大洞径、长斜井开挖积累了宝贵的经验。     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

盐16井全封闭边界油藏的确定及评价

充分运用试井解释成果，以尽量少的井确定一个油藏的范围及储量面积，加快勘探速度，提高勘探效果，近年来在胜利油田得到了较充分的应用。根据盐16井的电子压力计探边恢复试井资料解释成果，确定了该井沙四段砂砾岩体为全封闭边界油藏，以及具体的形状、储量面积及边界大小，并对此进行了评价，为决策部门提供了准确的勘探依据。通过在盐16井南部钻的一口空井（盐161井），证实了本次试井解释结果的可靠性。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。     

一种主机与网络相结合的漏洞扫描工具的设计与实现

计算机安全问题是在信息化过程中急需解决的问题 ,而安全漏洞的发现对保护系统安全有着非常重要的意义。网络管理人员由于种种原因 ,很难及时、全面地测试系统的安全性。因此 ,设计一种能代替他们进行测试的工具就显得十分必要。本文首先对漏洞扫描的原理进行了分析 ,主要介绍了一种主机与网络相结合的安全漏洞扫描的设计及实现。     

导向钻井系统在多目标大井斜定向井中的应用

详细介绍了C-D井在钻进过程中井眼轨迹的控制过程,总结了在C-D井中使用导向钻井系统的成功经验。用1根导向马达、2套钻具组合、3只牙轮钻头顺利地完成了定向、增斜、稳斜及降斜,7个目标点一次击中,且最小靶心距仅0.99m。用15d完成了这口斜深2287.09m、井斜58.40°、水平位移903.11m的多目标定向井,钻穿目标点之多、实钻井眼剖面符合率之高、施工难度之大、速度之快,在目前国内都处于领先地位。     

光刻胶灰化工艺与深亚微米线条的制作

随着器件尺寸的缩小，细线条的制作成为很关键的工艺，普通光学光刻已接近其分辨率的极限，而电子束光刻和Ｘ射线光刻技术复杂、费用昂贵。本文对光刻胶灰化工艺进行了分析和研究，并应用此工艺进行了深亚微米线条的制作，在普通光学光刻机上制作出宽度小于０．２５μｍ细线条。我们已将此工艺成功地应用在深亚微米ＭＯＳＦＥＴ的制作中。