三峡水电站ALSTOM机组低水头运行稳定性分析

混流式水轮机的水力稳定性与机组水力工况密切相关。以三峡电站左岸6号机组稳定性试验为例，分析了ALSTOM机组的低水头运行稳定性。根据试验分析结果，可将机组运行工况划分为小负荷区、涡带振动区、大负荷运行区。小负荷区机组效率较低，机组不宜在此区间运行；大负荷区机组运行稳定性最佳，但机组应避开强涡带工况区和特殊频率振动区运行。     

现行规范对“锁住区”起点高度简化处理的影响

通过工程实例及理论分析 ,对横向风振“锁住区”问题进行了探讨 ,对《建筑结构荷载规范》(GB5 0 0 0 9— 2 0 0 1 )中有关这一方面内容存在的一些问题进行了分析 ,希望对工程设计人员能有所帮助     

机械结构动态改进技术在电动机振动噪声防治中的应用

本文介绍了结构实验模态分析、灵敏度分析和局部结构改进分析等先进的结构动态改进技术的基本原理,并由此对Y112M-4型电动机的机座进行了计算和分析,确定出一个结构改进方案.经实际改进试验验证,这一改进可有效地抑制电动机电磁振动和电磁噪声的传递,具有明显的减振降噪作用.     

Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

旋转导向钻井偏心稳定器横向振动研究

旋转导向钻井偏心稳定器横向振动研究是国家863“可控(闭环)三维轨迹钻井技术”课题研究的部分内容。选取偏心稳定器的心轴作为研究对象,以偏心稳定器心轴连续梁系统的横向振动模型受力分析为基础,根据课题研究中所设计的心轴结构形式,建立了与实际情况较为接近的三铰支点的连续梁系统横向振动方程;并分析了偏心稳定器横向振动对钻井工具和钻具系统的影响,为合理进行心轴设计以及偏心稳定器样机在现场的正确使用和钻井参数的合理选择,提供了科学的理论依据和实用的计算方法。计算实例表明,当钻压范围选择在80~250kN时,215.9mm井眼钻进中的确存在19~20、61~63、162~163r/min前三阶横向共振转速区间,因此在选择钻井参数时应通过钻压与转速的配合,尽可能避开横向共振转速,以保证下部钻具组合系统及作业安全。     

潜油电机碟形弹簧的动力学分析

为了降低潜油电泵机组的振动对止推轴承性能的影响,在潜油电机中节和下节的止推轴承静块底部安装了蝶形弹簧。用有限元方法进行模态分析,确定了蝶形弹簧的主振型和固有频率,然后进行瞬态动力学分析,求解蝶形弹簧在一定载荷下的应力和位移。依此设计的蝶形弹簧将进一步延长止推轴承的使用寿命。     

空调器中多翼离心风机的噪声研究及结构优化

采用逐步回归法对大量的多翼离心风机实验数据进行拟合,针对家用空调行业中以噪声为其最重要 的考核标准,得出了噪声与叶轮结构参数及风机性能参数间的近似关系式,并以噪声为目标函数进行了优化计算。     

A Theoretical Framework for Core Material Properties Identification in Cellular Solids using Novelty Detection

Abstract:  This paper presents a novelty detection-based technique to identify core material properties of honeycombs and cellular structures. A numerical model (finite element) representing full scale and/or reduced size of the cellular solid is used to generate transmissibilities between topological homologous points at cells in different locations. In order to make the procedure robust against noise, these transmissibilities are artificially corrupted. This step is representative of a series of experimentally obtained measurements which automatically return information relating to the size and shape of data noise along with the mean measurement. The next stage, both in this paper and in the proposal for the experimental approach, is to generate several further sets of transmissibilities from the finite element model; the only difference being that the core material properties are altered from the original values. A novelty detection framework is then adopted to find a similarity measure between each of these 'test' transmissibilities and the original set thereby identifying the material properties. Although this work is concerned with identifying only one material property, the methodology extends to identifying several properties.     

KMLS型立式砂泵的振动噪声产生原因及解决措施

针对KMLS型立式砂泵振动、噪声产生原因及其表现特征,提出了解决措施。通过对这些原因的分析研究,可以提供泵设计者和生产者在减少砂泵振动方面采取相应的措施,使KMLS型立式砂泵能更好的服务于用户。     

Termites live in a material world: exploration of their ability to differentiate between food sources.

Drywood termites are able to assess wood size using vibratory signals, although the exact mechanism behind this assessment ability is not known. Important vibratory characteristics such as the modal frequencies of a wooden block depend on its geometry and boundary conditions; however, they are also dependent on the material characteristics of the block, such as mass, density and internal damping. We report here on choice experiments that tested the ability of the drywood termite Cryptotermes secundus to assess wooden block size using a solid wooden block paired with a composite block, the latter made of either wood and aluminium or wood and rubber. Each composite block was constructed to match mass or low-frequency vibratory modes (i.e. fundamental frequency) of the solid wooden block. The termites always chose the blocks with more wood; they moved to the solid wooden blocks usually within a day and then tunnelled further into the solid wooden block by the end of the experiment. Termites offered composite blocks of wood and rubber matched for mass were the slowest to show a preference for the solid wooden block and this preference was the least definitive of any treatment, which indicated that mass and/or damping may play a role in food assessment. This result clearly shows that the termites were not fooled by composite blocks matched for mass or frequency, which implies that they probably employ more than a single simple measure in their food assessment strategy. This implies a degree of sophistication in their ability to assess their environment hitherto unknown. The potential importance of alternative features in the vibrational signals is discussed.