钡盐法处理六价铬电镀废水及最优工艺参数研究

使用钡盐法对铬废水处理,对p H值在废水中的初值、反映温度计量结果、重铬酸钾的浓度等,在回收六价铬的影响效果进行了分析。对废水中的六价铬使用了源自吸收的分光光度法回收。经过处理后,废水中的p H为8~9的时候,六价铬的回收在9%。废水中的六价铬随着其浓度不断上升增加。超过10℃的时候,六价铬的反应没有非常大的影响,但是当温度降低到10℃以下的时候,回收率就逐步下降了。经过处理之后,六价铬的浓度达到了0.276 7 mg/L,达到了相关规定的标准。     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

内插法在相关干涉仪测向体制中的应用

测向误差的减小一直以来都是无线电测向精度提高的一个难点,对于不同的测向体制所采用的减小测向误差的方法都不尽相同。本文主要介绍的是相关干涉仪测向体制的基本原理以及通过内插法的应用来减小测向误差的方法。     

Grain mapping to freeform surface for machining using parameter-based incremental tracking method

This paper presents a novel method for mapping a texture for machining onto a freeform surface. When a grain texture designed on a 2D plane is projected onto a freeform surface simply, the texture is distorted along the curvature of the surface in the projection direction. Therefore, a method is required to suppress this distortion. The algorithm proposed in this paper rapidly generates a point cloud that represents a texture with less distortion on a simply connected parametric surface. Specifically, four equations that express local geometry constraints instead of conventional parameterization methods are presented to reduce the distortion between adjacent points on the point cloud. Solving these equations can generate grain textures on freeform surfaces. This paper examines two grain images mapped to two freeform surfaces that were prepared as case studies to demonstrate the effectiveness of the proposed method.     

Preparation of CaO granules using the granulation method

ABSTRACT

Improving the hydration resistance of CaO particle in manufacturing and application of free CaO-containing materials has practical significance. In this study, CaO granules was made from Ca(OH)₂ particles, which were fabricated by the granulation method. The results showed that the hydration resistance of the CaO granules which was prepared under 1700?r?min^?1 was the best, the CaO granules was sintered well in calcination process, the shell of CaO granules was relatively dense, which improves the hydration resistance of CaO granules, and the rate of hydration weight increment was 0.58% after placed in the air for 20 days under a temperature of 10–14°C and a relative humidity of 57–81%.     

Cost-minimization analysis of a working vacation queue with N-policy and server breakdowns

This paper investigates the N-policy M/M/1 queueing system with working vacation and server breakdowns. As soon as the system becomes empty, the server begins a working vacation. The server works at a lower service rate rather than completely stopping service during a vacation period. The server may break down with different breakdown rates during the idle, working vacation, and normal busy periods. It is assumed that service times, vacation times, and repair times are all exponentially distributed. We analyze this queueing model as a quasi-birth–death process. Furthermore, the equilibrium condition of the system is derived for the steady state. Using the matrix-geometric method, we find the matrix-form expressions for the stationary probability distribution of the number of customers in the system and system performance measures. The expected cost function per unit time is constructed to determine the optimal values of the system decision variables, including the threshold N and mean service rates. We employ the particle swarm optimization algorithm to solve the optimization problem. Finally, numerical results are provided, and an application example is given to demonstrate the applicability of the queueing model.     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.     

Design and synthesis of foam glasses from recycled materials

Recycling has emerged as an environmental key point due to the diminishing of natural resources and the generation of ever-increasing amounts of industrial solid wastes. Glass wastes are among the materials that attract great interest in the recycling concept. This work presents the results of foams production from four series of compositions. The first series comprises powders of a sodium-calcium-silicate sheet glass cullet as the main component, an alkali-earth aluminosilicate glass as an additive, and a reagent grade silicon carbide (SiC) powder as gassing agent. In the second series, the glass cullet was used in combination with fly ashes (FLA) as main components, while SiC waste from abrasive paper served as foaming agent. In the third and fourth series, carbonates (calcite and dolomite) were used for foaming powder mixtures composed of sheet glass cullet and FLA, and powdered cathode ray tube panel glasses, respectively. All the processing parameters, including the main components, the nature and content of foaming agents are shown to play a crucial role on the foaming ability and final properties of the glass foams.     

Multiplex PCR system to track authorized and unauthorized genetically modified soybean events in food and feed

A diverse range of genetic elements has been used to develop genetically modified organisms (GMOs) over the last 18 years. Screening methods that target few elements, such as the Cauliflower Mosaic Virus 35S promoter (P-35S) and Agrobacterium tumefaciens nopaline terminator (T-nos), are not sufficient to screen GMOs. In the present study, a multiplex PCR system for all globally commercialized GM soybean events was developed to easily trace the events. For this purpose, screening elements of 24 GM soybean events were investigated and 9 screening targets were selected and divided into three individual triplex PCR systems: P-35S, ribulose-1,5-bisphosphate carboxylase small subunit promoter of Arabidopsis thaliana, T-nos, T-35S, pea E9 terminator, open reading frame 23 terminator of A. tumefaciens, proteinase inhibitor II terminator of potato, acetohydroxy acid synthase large subunit terminator of A. thaliana, and the revealed 3′ flanking sequences of DP-305423-1. The specificity of the assays was confirmed using thirteen GM soybean events as the respective positive/negative controls. The limit of detection of each multiplex set, as determined using certified reference materials of specific GM events, ranged from 0.03 to 0.5%, depending upon target. Furthermore, 26 food samples that contained soybean ingredients, which were purchased from the USA, China, Japan, and Korea, were analyzed, 17 of which contained one or more GM soybean events. These results suggest that the developed screening method can be used to efficiently track and identify 24 GM soybean events in food and feed.