生物可降解PCL/PLA开孔发泡材料制备及吸油性能

以聚己内酯（PCL）为基体，添加不同含量聚乳酸（PLA）熔融共混制备具有不同分散相形态的PCL/PLA共混物，利用超临界二氧化碳（scCO₂）微孔发泡工艺制备不同发泡倍率和开孔率的PCL/PLA多孔材料用于吸油应用。针对边长3 mm正方体样品溶解度实验发现100 min后CO₂在PCL中已达到饱和吸附状态。PLA分散相含量的增加显著增大了PCL/PLA共混物泡孔密度，并使共混泡孔尺寸减小且分布更加均匀；发泡温度升高6℃，泡孔尺寸增大50%，发泡倍率增大38%，开孔率减小了20%。PCL/PLA开孔材料具有明显的亲油疏水性，发泡倍率越高，疏水性越好；针对花生油和硅油的吸油实验发现材料吸油率与发泡倍率和开孔率整体呈正比，实际吸油量高于理论计算值，10次循环吸油测试后样品吸油率仅降低8.5%，材料吸油量与油品特性黏度关系不大。     

测井资料在优选压裂层位中的应用

压裂是低孔、低渗油层改造的主要增产措施。根据常规测井资料、岩石物理实验分析数据及试油成果。研究储层四性关系，确定区块的低孔、低渗储层评价标准。进一步对油层进行分类，有针对性地为油层压裂提供施工层位和准确的储层参数。通过商543区块实例，阐述了选择压裂层位的方法。     

Effects of Rare Earths on Toughness of 31Mn2SiRE Wear-Resistance Cast Steel

The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.     

高分散度Pt/C电催化剂的制备

Cabot公司Vulcan XC-72型炭黑，经过H2O2氧化处理后作为Pt的载体，H2PtCl6作为金属前驱体制备了高度分散的Pt/C催化剂。讨论了不同条件下H2PtCl6在炭黑上的吸附性能。载体经过H2O2氧化处理24h,H2PtCl6在pH=9下吸收48h，H2 350℃还原2h，可以制备出铂晶粒平均大小为1.8nm的Pt/C电催化剂。     

Capture of Organic Vapors Using Adsorption and Electrothermal Regeneration

Activated-carbon-fiber cloth (ACFC) is an alternative adsorbent to granular activated carbon (GAC) for removing and recovering organic vapors from gas streams. Electrothermal desorption (ED) of ACFC provides rapid regeneration while requiring less energy compared to traditional regeneration techniques used with GAC. This paper provides proof-of-concept results from a bench-scale ACFC adsorption system. The automated system captured 1,000 ppmv of hazardous air pollutants/volatile organic compounds (HAPs/VOCs) from air streams and demonstrated the use of ED, using ac voltage, to recover the HAP/VOC as a pure liquid. The desorbed HAP/VOC condensed onto the inner walls of the adsorber and was collected at the bottom of the vessel, without the use of ancillary cooling. Seventy percent of the HAP/VOC was collected per cycle as condensate, with the balance being retained in the regenerated adsorber or recycled to the second adsorber. ED with in-vessel condensation results in minimal N2 consumption and short regeneration cycle times allowing the process to be cost competitive with conventional GAC-based adsorption processes. This technology extends the application of carbon adsorption systems to situations that were previously economically and physically impractical.     

Annealing effects on structural and electrical properties of fluorinated amorphous carbon films deposited by plasma enhanced chemical vapor deposition

The annealing effects on the structural and electrical properties of fluorinated amorphous carbon (a-C:F) thin films prepared from C₆F₆ and Ar plasma are investigated in a N₂ environment at 200 mTorr. The a-C:F films deposited at room temperature are thermally stable up to 250 °C, but as the annealing temperature is increased beyond 300 °C, the fluorine incorporation in the film is reduced, and the degree of crosslinking and graphitization in the film appears to be enhanced. At the annealing temperature of 250 °C, the chemical bond structures of the film are unchanged noticeably, but the interface trapped charges between the film and the silicon substrate are reduced significantly. The increased annealing temperature contributes the decrease of both the interface charges and the effective charge density in the a-C:F film. Higher self-bias voltage is shown to reduce the charge density in the film.     

不锈钢塔器在硫酸装置中的应用

摘 要:主要介绍Sasol Agri公司硫酸四系统的技术改造,分两步进行,第一步更换转化器、热换热器及主省煤器,生产能力由1600t/d提高到1750 t/d,且鼓风机出口压力很低。第二步更换干燥塔、二吸塔及冷换热器,连续生产能力在1950 t/d以上。使用不锈钢材质及克瓦纳·凯密迪公司专有的换热器,使装置的改造相当成功,维护及操作费用较低,并具有较大的灵活性和可操作性。     

低流度油藏分类及开发特征研究

低流度油藏指流度低于30×10-3μm2/mPa.s的油藏。根据流度大小以及油藏在开发生产中表现出的特征,可将低流度油藏分为一般低流度油藏、特低流度油藏和超低流度油藏。对大港低流度油藏的研究表明,由于低流度油藏地质情况复杂,地层认识不清,因而开发特征复杂,表现为采油速度低,采出程度和采收率低;注水效果差,油藏井距不适应;油井见水后含水迅速上升,产量则急剧下降。     

湘中海相浅层湘冷1井酸压工艺研究及应用

湘冷1井具有气层埋藏浅（400m-500m）、纵向上裂隙发育的特点，属低孔、低渗的含泥质灰岩致密储层。大量室内实验和研究采用“前置液酸压＋闭合酸化”工艺技术，并优选了相应降阻酸和闭合酸配方。通过酸压实现了该井工业油气流的突破，取得了明显的增产效果，为新区海相浅层气的开发探索出了一套成熟的改造增产措施。     

片式多层陶瓷微波谐振器

介绍了片式陶瓷微波谐振器的工艺过程、谐振器的结构以及结构对谐振器参数的影响,谐振器与外电路的耦合采用耦合间隙的方法与谐振单元在同一层内实现,这种新结构既可给制备工艺带来方便,又可减少工艺所带来的误差。用多层陶瓷工艺技术,用高介电常数、低温烧结微波陶瓷实现了中心频率为1GHz,有载品质因数大于80的试验双端口多层微波谐振器。微波谐振器体积小,整个谐振器的尺寸为7mm×2mm×1mm,适用于表面贴装技术。