管道流体瞬态—水汽锤计算原理

文中介绍了核电站管道中流体瞬态——水汽锤的计算原理;既适用于液体介质的水锤计算,也适用于可压汽体的汽锤计算.对于一些典型管道部件的处理方法,文中也作了讨论。     

水蒸汽喷射泵系统实用设计软件的开发

本文在Turboc环境下开发了多级蒸汽喷射泵系统的设计软件，该软件包括了压缩比优化分配、单级喷射泵结构尺寸设计和冷凝器的结构尺寸设计等内容，使设计人员能够根据具体的工艺条件，快速地完成多级喷射泵系统的设计，对于提高多级喷射泵系统的工作稳定性、节省能源具有实际意义。     

蒸汽减压站自控系统的巧设计

蒸汽是石油化工装置中最重要的物料。随着石油化工工业的迅猛发展 ,蒸汽在其中扮演着越来越重要的多重角色。因此 ,对蒸汽系统的平稳控制 ,对石油化工生产装置平稳、高效地运行是至关重要的。传统的蒸汽减压站自控系统基建投资大 ,紧急情况下靠人工手动操作稳定蒸汽压力系统 ,往往造成生产的波动或大面积的停车。针对传统蒸汽减压站自控系统的弱点 ,提出蒸汽减压站自控系统的优化设计方案 ,该方案得以在大型生产装置成功应用。新方案不但节省了大量的基建投资 ,而且取得了良好的生产效益     

合成氨扩能改造中锅炉存在的问题及采取的措施

针对天脊集团年产30万t合成氨扩能改造,给2台225t/h高压锅炉带来的除氧器热量过剩、锅炉给水温度升高、主蒸汽温度降低等一系列问题,分析了产生问题的原因,从节约能源、提高锅炉效率考虑,提出了相应的解决问题的办法:利用热量分流、改造省煤器管、增加二级过热器受热面积。经过3年多的生产实践证明,取得了良好的效果。     

Drying Kinetics of a Porous Spherical Particle and the Inversion Temperature

A model is presented for drying of a single porous particle with superheated steam and humid air. Experimental data for spherical porous ceramic particle reported in the literature were used for the validation of the model. An inversion temperature at which the evaporation rates within superheated steam and humid air are equal was predicted. The effect of thermophysical properties of the particle (permeability 10^-14 - 10^-17 m², diameter 3 × 10^-3 - 10 × 10^-3 m) and operating variables (gas mass flux 0.26 - 0.78 kg m^-2 s^-1, drying agent temperature 120-200°C) is tested. The inversion temperature is shown to be affected by the thermophysical properties of the porous particle and of the drying agent.     

运用现代CFD方法设计高效率的汽轮机(续前期)

论述了运用现代计算流体动力学(ComputationalFluidDynamics,CFD)技术设计高效率汽轮机的方法,典型应用的实例有全三维叶片级流场、叶片汽封和排汽蜗壳计算。计算结果和实际是相符的。进一步对结构性单元和非结构单元程序的计算结果进行了比较,已证明,非结构单元CFD程序用于复杂形状的流场计算时,结果与实际相当一致,并具有独特的功能。     

宾馆酒店蒸汽冷凝水回收问题剖析

分析了宾馆酒店进行冷凝水回收所遇到的各种问题，提出了应对策略和解决方法，介绍了取得的应用效果。     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Geochemical characteristics of the Yufuin outflow plume, Beppu hydrothermal system, Japan

Thermal water at Yufuin (Kyushu Island, Japan) is tapped through about 820 shallow wells and used mainly for hot-spring bathing purposes. Chemical and isotopic data for fluids from wells and fumaroles in Yufuin and Beppu indicate that the thermal activity at Yufuin represents a dilute, westward-flowing hydrothermal outflow plume from the Beppu hydrothermal system. Two other (eastward-flowing) outflow plumes have long been recognized at Beppu, but the Yufuin outflow plume is first recognized here. The Yufuin outflow plume is apparently a mixture of two end-member fluids: (1) deep high-temperature (250–300°C) fluid from the Beppu system having high chloride concentration (1400–1600 mg/L) and a δ¹⁸O value near −6.0%, and (2) meteoric water having low chloride concentration (≤7 mg/L) and a δ¹⁸O value near −9.2%.A permeable conduit for the vertical and lateral transport of deep fluid from the Beppu system is provided by the Yufuin Fault zone, which extends westward from the southern flank of Mt. Tsurumi volcano to the town of Yufuin. Stable isotope ratios and chloride concentrations for shallow groundwaters near the eastern end of the fault, at an elevation near 700 m, are consistent with those required for the low-chloride meteoric end-member of the Yufuin thermal waters. Recharge of this meteoric water, as well as mixing with the Beppu deep fluid, may occur along the Yufuin Fault. Enthalpy-chloride relations indicate additional conductive heating of the Yufuin waters, in the amount of 350–500 kJ/kg beyond that which can be accounted for by mixing between Beppu deep fluid and meteoric water. This could be a result of conductive heating with convection to a depth of 1–2 km. Estimates of the magnitude of the heat source for the Beppu hydrothermal system should take into account the heat being discharged at Yufuin.