Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。     

影响掺矿渣的钢纤维砼强度的主要因素

研究结果表明 :水胶比、胶凝材料用量、钢纤维掺量、矿渣代水泥量对钢纤维砼强度影响显著。当矿渣取代水泥 10 %时 ,钢纤维砼强度最高。经试验选择出一个具有良好和易性和较高强度 (118MPa)的钢纤维砼配合比 ,为掺磨细矿渣的中含量超短异形钢纤维砼的设计和施工提供了试验依据     

TP130TT高抗挤套管研究与应用

为了提高盐层段固井质量 ,中原油田研究开发了 TP130 TT高抗挤套管 ,性能试验评价表明 ,其抗挤强度超过 16 0 MPa,并给出了其固井质量评价标准。在中原油 346口井中的应用表明 ,该套管有效地解决了盐层段套管损坏问题 ,延长了油气水井寿命 ,经济效益和社会效益显著。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

钻探用变量泥浆泵曲轴强度的计算

随着钻探业的不断发展 ,日趋需要大功率的泥浆泵 ,文章介绍了大变量泥浆泵机组中曲轴的设计。     

首钢烧结配加扬地粉试验研究

介绍了首钢原料条件下配加扬地粉对烧结生产影响的实验室研究.随着扬地粉配入量的增加,烧结矿转鼓强度、成品率改善,燃耗有少量上升,利用系数增加,低温还原粉化指数变差.研究结果表明:在首钢目前条件下,配入10%～20%的扬地粉是可行的.二烧车间进行了扬地粉工业试验,其最高配比达到30%,工业试验时烧结各项指标变化与实验室试验结果基本一致.     

Concurrent effect of microporosity and chemical structure on the equilibrium sorption properties of cellulose-based hydrogels

Polyelectrolite hydrogels are crosslinked polymers which display high sorption capacity in water and water solutions. They are widely used in the marked of personal hygiene products, as well as in other biomedical and industrial applications. In the most industrial application they are not biodegradable and prepared starting from acrylamide.In this work, the chemical-physical analysis of a novel class of natural polymers-based microporous superabsorbent hydrogels has been presented. The main focus is the definition of the relationship between material's chemical-physical structure and its equilibrium sorption properties.The effect of the variation of the degree of crosslinking, the polyelectrolyte nature of the backbone and the hydrogel microporosity on its swelling properties has been analysed, and a good agreement with the theoretical statements has been displayed.The effect of the ionic strength and the pH of the external solution in contact with the hydrogel on its equilibrium sorption properties has also been assessed, and an high sensitivity to these variations was detected for all the tested chemical compositions and physical structures.This work have to be considered part of the efforts towards the reduction of the environmental impact of the large scale consumption industrial polymer based products.     

螺栓角钢钢节点的三维非线性有限元分析

对螺栓角钢钢节点半刚性连接采用非线性有限元分析方法 ,对连接中的主要构件的顶部、底部、腹板角钢、高强螺栓、梁翼缘、柱翼缘和柱翼缘加劲肋进行三维非线性有限元精细模拟 ,针对有无柱加劲肋、有无腹板角钢等几种连接的情况进行比较分析 ,探讨了螺栓角钢半刚性连接的受力性能。