高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。     

A computer aided design method for car form and its application based on shape parameters

In the early design stage, automotive modeling should both meet the requirements of aesthetics and engineering. Therefore, a vehicle CAD (computer aided design) model that can be easily adjusted by feedbacks is necessary. Based on CE-Bézier surface, this paper presents a set of algorithms for parametric segmentation and fairing surface generation in a car model. This model is defined by a simplified automotive template and relevant control points, shape parameters and segmentation parameters, which can be modified to alter the car form efficiently. With this model and the corresponding adjustment method, more than fifty various vehicle models are established in this research according to different parameters. And two methods for calculating similarity index between car models are constructed, which are suitable for brand design trend analysis and modelling design decisionmaking.     

钛合金表面多磁极耦合旋转磁场光整加工特性

面向激光增材制造钛合金表面的光整加工需求，设计出一种多磁极耦合旋转磁场光整加工装置来研究光整加工特性。基于ANSYS Maxwell仿真软件分析了光整加工装置的磁场强度分布。搭建了实验光整平台，分析了主轴转速、C轴转速和加工间隙对表面质量的影响。结果表明，在主轴转速500 r/min、C轴转速160 r/min和加工间隙0.7 mm的加工条件下，表面粗糙度Ra由5.991 μm下降至0793 μm。扫描电子显微镜(SEM)观测表明，光整后的钛合金表面沉积层消失，表面质量得到显著改善。     

Grain mapping to freeform surface for machining using parameter-based incremental tracking method

This paper presents a novel method for mapping a texture for machining onto a freeform surface. When a grain texture designed on a 2D plane is projected onto a freeform surface simply, the texture is distorted along the curvature of the surface in the projection direction. Therefore, a method is required to suppress this distortion. The algorithm proposed in this paper rapidly generates a point cloud that represents a texture with less distortion on a simply connected parametric surface. Specifically, four equations that express local geometry constraints instead of conventional parameterization methods are presented to reduce the distortion between adjacent points on the point cloud. Solving these equations can generate grain textures on freeform surfaces. This paper examines two grain images mapped to two freeform surfaces that were prepared as case studies to demonstrate the effectiveness of the proposed method.     

Technical and economic analysis of solvent-based lithium-ion electrode drying with water and NMP

Processing lithium-ion battery (LIB) electrode dispersions with water as the solvent during primary drying offers many advantages over N-methylpyrrolidone (NMP). An in-depth analysis of the comparative drying costs of LIB electrodes is discussed for both NMP- and water-based dispersion processing in terms of battery pack $/kWh. Electrode coating manufacturing and capital equipment cost savings are compared for water vs. conventional NMP organic solvent processing. A major finding of this work is that the total electrode manufacturing costs, whether water- or NMP-based, contribute about 8–9% of the total pack cost. However, it was found that up to a 2?×?reduction in electrode processing (drying and solvent recovery) cost can be expected along with a $3–6?M savings in associated plant capital equipment (for a plant producing 100,000 10-kWh Plug-in Hybrid Electric Vehicle (PHEV) batteries) using water as the electrode solvent. This paper shows a different perspective in that the most important benefits of aqueous electrode processing actually revolve around capital equipment savings and environmental stewardship and not processing cost savings.     

CFD Modeling of Active Volume Creation in a Non‐Newtonian Fluid Agitated by Submerged Recirculating Jets

Computational fluid dynamics (CFD) models were employed to investigate flow conditions inside a model reactor in which yield stress non‐Newtonian liquid is mobilized using submerged recirculating jets. The simulation results agree well with the experimental results of active volume in the reactor obtained using flow visualization by the authors in a previous study. The models developed are capable of predicting a critical jet velocity (v_c) that determines the extent of active volume obtained due to jet mixing. The v_c values are influenced both by the rheological properties of the liquid and the nozzle orientation. The liquid with higher effective viscosity leads to higher v_c for a downward facing injection nozzle. However, an upward facing injection nozzle along with a downward facing suction nozzle generates enhanced complementary flow fields which overcome the rheological constraints of the liquid and lead to lower v_c.     

Distributed learning consensus control based on neural networks for heterogeneous nonlinear multiagent systems

This paper considers a novel distributed iterative learning consensus control algorithm based on neural networks for the control of heterogeneous nonlinear multiagent systems. The system's unknown nonlinear function is approximated by suitable neural networks; the approximation error is countered by a robust term in the control. Two types of control algorithms, both of which utilize distributed learning laws, are provided to achieve consensus. In the provided control algorithms, the desired reference is considered to be an unknown factor and then estimated using the associated learning laws. The consensus convergence is proven by the composite energy function method. A numerical simulation is ultimately presented to demonstrate the efficacy of the proposed control schemes.     

咖啡渣活性炭的制备、表征及其对Cr(Ⅵ)的吸附机制研究

以碘吸附值为评价指标，活化时间、活化温度和浸渍比为影响因素，采用响应面法试验设计对磷酸活化法制备咖啡渣活性炭的工艺条件进行优化，并通过静态吸附试验研究了不同吸附时间、溶液pH值和吸附温度条件下，活性炭对水溶液中Cr（Ⅵ）吸附性能的影响，最后利用Langmuir、Freundlich吸附等温方程、准一级动力学方程、准二级动力学方程和颗粒内部扩散方程进行拟合。试验结果表明，制备咖啡渣活性炭的最佳工艺条件为活化时间1 h、活化温度498℃、浸渍比1.72；在此条件下活性炭得率为30.4%，碘吸附值为（799±16）mg/g，比表面积为1 006 m²/g，孔容为0.779 cm³/g、微孔孔容为0.051 cm³/g、平均孔径为3.088 nm。较低pH值和较高温度能够促进活性炭对Cr（Ⅵ）的吸附；Langmuir等温方程能够更好地描述活性炭对Cr（Ⅵ）的吸附效果；活性炭对Cr（Ⅵ）的吸附分3个阶段：快速吸附阶段、慢速吸附阶段和吸附平衡阶段，10 min内可完成吸附总量的79%，360 min内达到吸附平衡，该吸附过程符合准二级吸附动力学方程。分析表明咖啡渣活性炭对Cr（Ⅵ）的吸附主要为单分子层的化学吸附。     

潮流能水平轴水轮机在剪切来流下的水动力分析

采用基于计算流体力学方法的全尺度数值模拟计算,建立了适用于潮流能水轮机模拟的剪切来流环境,通过数值计算结果,对潮流能水轮机随时间变化的宏观力和流场特征进行了系统分析,探索水轮机在复杂工况下的水动力特性规律。结果表明,水轮机整个叶轮的总体平均受力在剪切流工况中未受到明显影响; 单个叶片的瞬态轴向力系数和瞬态轴向扭矩系数在旋转周期内出现了明显的周期性变化,且周期性变化幅值随转速增大而增大; 非定常的瞬时轴向扭矩和力的周期性振荡容易引起单个叶片的结构性振动,可能对水轮机的机械结构造成影响。