Prediction of the twisting moment and axial force in a circular rubber cylinder for combined extension and torsion based on the logarithmic strain approach

The scope of the present work is the application of a particular class of strain energy function, based on the logarithmic strain, for the prediction of the twisting moment and axial force of a rubber circular cylinder under combined extension and torsion. The strain energy function involves four material parameters three of which are determined by fitting published experimental data from simple tensile and compression tests of natural rubber. One of the parameters of the proposed model has physical meaning, and it is equal to one ninth of the initial modulus of elasticity of the material. Hence, the number of unknown parameters is reduced to three. The logarithmic strain energy function is then applied to a combined extension and torsion problem of a rubber circular cylinder to check its performance for more complicated deformations. The results are compared with corresponding experimental and theoretical solutions available in the literature to validate the proposed model. It is found that the proposed strain energy function apart from predicting the common modes of deformations is also capable to determine more complicated types of deformation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Increasing the precision of a device used to determine the dynamic coefficient of friction

A theoretical evaluation of the potential application of a device with inclined plane for determining the dynamic coefficient of friction is given. Structural changes in the device that make it possible to increase its precision are proposed. Computational equations for estimating the resolution of the device are presented. __________ Translated from Izmeritel’naya Tekhnika, No. 11, pp. 24–26, November, 2007.     

带状大比例尺地形图在分带接边处的接边处理

介绍带状大比例尺地形图在分带处高斯平面上拼接的原理和方法，并编制了相应的接边数据处理程序。作业实践说明，该接边方法简便实用，计算程序正确可靠。     

复杂环境下超长深基坑工程实例研究

深基坑工程长近百米，周边环境复杂，施工作业条件差，结合工程设计留设的后浇带，采用适合的支护结构体系、止水帷幕技术、土方开挖方法，加强施工监测，着力于减少对周边环境的不利影响，为类似条件的深基坑工程的施工提供了有益的经验。     

济钢小板坯连铸机φ360mm拉辊优化改造

为解决小板坯连铸机φ360mm拉辊断颈、断辊问题，对拉辊原设计及现场使用条件进行了分析，将材质由55^#锻钢改为35CrNiMo，辊身与辊颈处改为圆锥台式，同时加大辊颈处过渡圆弧并磨削处理，延长水冷孔通过辊颈圆弧，从而使拉辊寿命由3～4个月延长到10～12个月，减少了事故损失，加快了生产节奏，年直接经济效益达49万元。     

误读与纠正

分析材料试验机度盘偏转角度小 (准确度低 )、试样打滑、定义 (上屈服强度 -下屈服强度 -屈服强度 )模糊、不同应力速率等导致误读 ,并针对误读原因提出纠正方法。     

静载荷和疲劳载荷作用下 C/Al 正交层压板的力学响应

本文讨论静载荷及疲劳载荷作用下 C/Al 正交层压板的力学响应,并考虑损伤过程中的临界现象,以此作为结构设计准则的基础。对静载荷作用的情况:(1)90°铺层的门槛应变ε_(FPF)随着约束程度增加而增加,而且开裂后的行为也受约束程度的影响。(2)经历加载-卸载再重新加载至断裂的过程后,初始试样存在一个剩余永久变形,其损伤状态可以用刚度的变化来表征;而疲劳试样在加载-卸载过程中刚度变化很小,反映其损伤达到一个稳定的状态。对疲劳载荷作用的情况:(1)对于给定的应力比 R,试样会趋于与它所承受的 S_(max)最大值相应的 SDS 状态。循环应力范围的不断增大,会引起基体损伤的增加,从而重新建立新的饱和损伤状态。(2)对于每一损伤状态均有一对应的循环应变范围 Δε。在 SDS 状态下,Δε保持不变。(3)以刚度下降为损伤参数对 C/Al 层压板进行了降级应力分析,并由此来预计在ΔS_(sh)以下,层压板不会发生疲劳损伤累积。     

乳化炸药的乳化物理模型和理想乳化模态

文章以平推流模拟了乳化炸药乳胶质的形成过程,并建立了机械强制乳化的物理模型及理想模态。     

差动光栅在精密测试中的应用

提出差动光栅概念,举例说明差动光栅在光纤面板刀口响应测试和材料形变自动监测系统等精密测试中的应用。     

LOW-CYCLE FATIGUE UNDER NON-PROPORTIONAL LOADING

A series of strain-controlled, low-cycle fatigue experiments have been conducted on 42CrMo steel under various loading paths including circular, square, cruciform, and rectangular paths. Present experiments have shown that there is additional hardening under non-proportional cyclic loading. Non-proportional cyclic additional hardening also results in a shorter life for multiaxial low cycle fatigue. A non-proportionality measure of strain path based on both a physical basis and macromechanical phenomena is proposed. The loading path effect on additional hardening is also described well. Low-cycle fatigue damage accumulation and the evolution process under non-proportional loading is analysed via the Continuum Damage Mechanics Model of Chaboche. A non-proportinality measure is introduced in the damage evolution equation and a modified Coffin-Manson type formula is derived. A novel fatigue life prediction approach based on the critical-plane concept of Brown and Miller is proposed.