变形介质中宾汉稠油驱替特征

通过建立变形介质中考虑启动压力梯度的一维两相宾汉稠油驱替的数学模型,并进行了数值求解,分析了地层变形以及启动压力梯度对水驱稠油的影响,分析表明:介质变形对含水饱和度的分布没有影响,而对地层压力的影响是非常显著的,随着变形介质弹性的增加,地层压力越来越低,并且越靠近注入端,地层压力下降越快;原油的启动压力梯度同时影响含水饱和度和地层压力的分布,在其它条件一定时,启动压力梯度的存在,造成地层压力的增加和平均含水饱和度的降低。在油田开发实际中,应考虑地层变形和启动压力梯度的影响,以提高原油采收率。     

真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

粗粒土渗透变形机制浅析

对砂卵砾石的渗透变形的形成条件进行了简要分析，在此基础上对渗透变形的形式进行了简要评价，并提出了渗透变形临界坡降的计算方法。     

我国氟碳铈矿选矿生产工艺进展

自１９９４年以来，随着轻稀土产品市场的好转，稀土行业的龙头工艺—稀土选矿生产工艺流程也得到了促进与发展，涌现出几种新的生产工艺流程和稀土矿物浮选药剂。本文就我国内蒙古白云鄂博矿、四川冕宁矿、山东微山矿的稀土选矿工艺流程予以介绍，并对上述地区生产工艺中存在的问题加以讨论。     

共轭梯度法在三维复杂流动数值分析中的应用

将多块网格技术运用于三维T型管复杂流场的网格生成，利用不完全乔列斯基预处理共轭梯度，双共轭梯度方法求解N－S方程的离散方程。计算表明上述方法有良好的收敛特性，适合于诸如T型管等复杂流动的分析。     

基于局部多项式逼近的变参数梯度估计算法

本文分析了梯度辨识算法跟踪时变系统的缺点，提出了一种新的基于局部多项式逼近的变参数梯度估计算法。本算法具有良好跟踪性能特别适用于时变系统跟踪且其对噪声的敏感程度与一般梯度估计方法相当。仿真结果验证了其良好性能。     

Effect of Pressure Gradient on Heat Transfer of Impinging Submerged Circular Jets

An experimental and numerical study have been carried out to investigate the distribution of radial local heat transfer coefficients of impinging submerged circular jets. Good agreement is achieved between the experimental results and the predicted value. Results show that the outer peak usually occurs at the radial location of r/d= 1.8~2.0, in which transition from laminar to turbulence happens resulting from disappeared pressure gradient abruptly, and that the inner peak appears rigidly at r/d=0.5, where the boundary layer has a minimum thickness because of elevating pressure gradient.     

On the existence and synthesis of multifinger positive grips

We study the criteria under which an object can be gripped by a multifingered dexterous hand, assuming no static friction between the object and the fingers; such grips are calledpositive grips. We study three cases in detail: (i) the body is at equilibrium, (ii) the body is under some constant external force/torque, and (iii) the body is under a varying external force/torque. In each case we obtain tight bounds on the number of fingers needed to obtain grip.We also present efficient algorithms to synthesize such positive grips for bounded polyhedral/polygonal objects; the number of fingers employed in the grips synthesized by our algorithms match the above bounds. The algorithms run in time linear in the number of faces/sides.The paper may be of independent interest for its presentation of algorithms arising in the study of positive linear spaces.Work on this paper has been supported by Office of Naval Research Grant N00014-82-K.-0381, National Science Foundation Grant No. NSF-DCR-83-20085, and by grants from the Digital Equipment Corporation, and the IBM Corporation.     

The Loss of Hydrophobic Polypeptides during Fermentation and Conditioning of High Gravity and Low Gravity Brewed Beer

The object of this study was to investigate the loss of hydrophobic polypeptides, which are important for foam quality and stability in finished beer. Loss of hydrophobic polypeptide due to fermenter foaming occurs during transfer of fermented wort since a gradient of hydrophobic polypeptides towards the surface is created during fermentation. Due to higher polyphenol levels in high gravity (20°Plato) wort, more hydrophobic polypeptides are lost due to cold break (cold trub) precipitation compared to low gravity (12°Plato) wort. Another important factor affecting the loss of hydrophobic polypeptides could be proteinase A activity during fermentation, especially in high gravity fermentation where the yeast is exposed the higher stress. During high gravity fermentation, where osmotic pressures are higher, ethanol levels become greater, and nitrogen‐carbohydrate ratios are lower, more proteinase A is released by the yeast. This release of proteinase A into fermenting wort could have implications for the foam stability of the finished product.     

复合形法优化内河航道重力式护岸

采用复合形优化法,结合《港口及航道护岸工程设计与施工规范》中推荐的抗滑、抗倾稳定的分项系数计算方法,并考虑了内河航道船形波等作用的影响效应,对重力式护岸断面进行了优化。