Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

生物预处理技术在天然产物提取中的应用研究进展

生物预处理技术运用于天然产物提取是借助微生物或生物酶的作用，在适当条件下对天然资源进行处理，破坏植物原料的细胞壁，促进天然产物释放到提取介质中，以提高分离效率，有助于保证天然产物活性。生物预处理技术按形式可以分为微生物发酵技术和生物酶处理技术。针对2种生物预处理技术的作用机制和应用进行综述，旨在为天然产物开发利用提供参考。     

Studying local liquid velocity in liquid–solid packed bed using the newly developed X-ray DIR technique

Combination of X-ray Digital Industrial Radiography (DIR) and Particle Tracking Velocimetry (PTV) techniques for local liquid velocity measurement (V_LL) has been newly developed and successfully applied for trickle bed reactor (TBR). The technique was validated against newly developed fiber optical probe technique. This work attempts to highlight the applicability of this newly developed technique on a liquid–solid packed bed reactor. In this work, liquid was represented by water and solids were represented by EPS beads. The EPS beads were chosen because of its low density property. Three superficial liquid velocities (V_SL) were applied to the system. The experiment was replicated four times. The digital industrial radiography (DIR) consists of a complementary metal oxide semiconductor (CMOS) digital detector and X-ray source. Results of this work suggest that the technique has been successfully applied and comparable with previous work that has been done in the literature. It also suggests that there will be a maximum measurable interstitial liquid velocity when it travel inside the packed bed. The measured V_LL can have a maximum range that is between 4 and 4.7 times that of its V_SL. For V_SL=0.42±±2%, the V_LL-Max is in between 1.7 cm/s and 1.9 cm/s, V_SL=0.84±±2%, the V_LL-Max is in between 3.6 cm/s and 4.0 cm/s, and for V_SL=1.11±±2%, the V_LL-Max is in between 4.3 cm/s and 4.8 cm/s.     

Copper–4,4′-dipyridyl coordination compound as solid reagent for spectrophotometric determination of reducing sugar employing a multicommutation approach

In this work a multicommuted flow system employing copper–4,4′- dipyridyl coordination compound as the solid-phase reagent for the spectrophotometric determination of reducing sugar was developed. The coordination compound was synthesized through a reaction of the 4,4′-dipyridyl and copper (II) nitrate, under hydrothermal conditions. The complex was characterized by infrared spectroscopy (FTIR), power X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and thermogravimetric analysis (TGA). Based on the characterization, a multicommuted spectrophotometric procedure for the determination of reducing sugar using copper (II) complex as solid reagent is proposed. The proposed method was based on the redox reaction between a monosaccharide, such as fructose and glucose (reducing sugar) and Cu(II). This reaction, mediated in an alkaline medium, produces a yellow compound that can be determined by absorption electronic spectroscopy (λ_ABS = 420 nm). Under optimum experimental conditions, a linear response ranging from 1.0 to 20.0 g L⁻¹ (R = 0.9978 and n = 5), a detection (3σ criterion) and quantification (10σ criterion) limit estimated at 0.23 and 0.75 g L⁻¹, respectively, a standard deviation relative of 4.7% (n = 7), for a reference solution of 10.0 g L⁻¹ reducing sugar, and a sampling rate of 75 determinations per hour were achieved. The proposed system was applied to the determination of reducing sugars in coconut water and juices. The analysis of ten samples and the application of the t-test to the results found, and those obtained using reference procedures (AOAC), provided no significant differences at a 95% confidence level. This system enabled the analysis of reducing sugar with ease and simplicity, providing a significant economy of the solid reagent (600 μg per determination) and reducing effluent generation.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Numerical investigation of a multichannel reactor for syngas production by methanol steam reforming at various operating conditions

A novel multichannel reactor with a bifurcation inlet manifold, a rectangular outlet manifold, and sixteen parallel minichannels with commercial CuO/ZnO/Al₂O₃ catalyst for methanol steam reforming was numerically investigated in this paper. A three-dimensional numerical model was established to study the heat and mass transfer characteristics as well as the chemical reaction rates. The numerical model adopted the triple rate kinetic model of methanol steam reforming which can accurately calculate the consumption and generation of each species in the reactor. The effects of steam to carbon molar ratio, weight hourly space velocity, operating temperature and catalyst layer thickness on the methanol steam reforming performance were evaluated and discussed. The distributions of temperature, velocity, species concentration, and reaction rates in the reactor were obtained and analyzed to explain the mechanisms of different effects. It is suggested that the operating temperature of 548 K, steam to carbon ratio of 1.3, and weight hourly space velocity of 0.67 h⁻¹ are recommended operating conditions for methanol steam reforming by the novel multichannel reactor with catalyst fully packed in the parallel minichannels.     

Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

磁絮凝强化技术处理厌氧消化污泥脱水液

为满足后续生物处理单元对固体悬浮物（SS）和铁浓度的进水要求，采用磁絮凝强化技术对厌氧消化污泥脱水液进行预处理。通过正交试验和单因素试验，本文考察了混凝水力条件、聚合氯化铝（PAC）投加量、聚丙烯酰胺（PAM）投加量、磁粉投加量及药剂投加顺序对磁絮凝效果的影响。试验结果表明：磁絮凝强化技术在快搅300r/min（2min）、慢搅100r/min（15min）、静置10min时，依次投加磁粉（40mg/L）、PAC（30mg/L）、PAM（4mg/L）时处理效果最好。在此运行条件下，SS和Fe³⁺去除率分别为97.61%、98.24%、絮凝指数（FI值）取得最大值、zeta电位绝对值最小，絮凝效果最佳。与对照相比，磁絮凝强化技术对SS和Fe³⁺去除率分别可提高3.70%和10.82%，同时絮体最大沉降速度可提高33%。磁絮凝技术处理后的出水不仅可以满足后续生物处理单元对SS和铁浓度的要求，还可以有效提高磁絮凝体的沉降速度，减小沉淀时间，具有较好的实用价值。