下游为干河床的溃坝水流数值模拟

应用二阶TVD—MacCormack格式计算了含间断波的二维浅水流动．模拟算例为下游是干河床、瞬间部分坝体溃决形成的溃坝水流运动．针对该格式，采用恰当的限制器使得解既不产生过大耗散，又具有高分辨率．     

在用航空润滑油可靠性评估方法的研究

介绍航空润滑油可靠性评估的相关质量指标及几种航空润滑油可靠性评估方法,分析了几种单参数航空润滑油可靠性评估方法,并提出两种基于油液多参数融合的油液工作状态分析方法,为提高航空润滑油的可靠性和按质换油提供有效的分析手段。     

湿H2S环境中金属材料腐蚀的研究

介绍了在湿H2S环境中金属材料的腐蚀试验标准、方法和手段并重点强调了在H2S试验过程中常遇到的一些问题的处理方法.最后,指出了应加强H2S腐蚀的基础性和系统性研究的研究方向.     

固定化酵母粒子中生产乙醇的定态分岔行为研究

运用变分原理和打靶法将分布参数系统的非线性边值问题转化为集总参数系统的初值问题，基于延拓算法，研究了固定床中球形固定化酵母粒子表面乙醇和葡萄糖浓度随参数的变化关系，得出了单颗粒固定化酵母生产乙醇的多定态特性。结果表明：随系统尺度三的变化，方程出现分岔点；方程的解与液相主体浓度有关。在某些条件下酵母粒子表面浓度有三个定态：在多定态区域，随三的增加，方程一个解支的乙醇浓度迅速增加，从而可以在固定床中通过控制粒径而使反应器达到较高的产率。研究结果为固定床反应器的开工及控制提供了重要的理论依据。     

Implicit integration and consistent tangent modulus of a time‐dependent non‐unified constitutive model

This paper describes the implicit integration and consistent tangent modulus of an inelastic constitutive model with transient and steady strain rates, both of which are time‐ and temperature‐dependent; the transient rate is influenced by the evolution of back stress decomposed into parts, while the steady rate depends only on applied stress and temperature. Such a non‐unified model is useful for high‐temperature structural analysis and is practical owing to the ease in determining material constants. The implicit integration is shown to result in two scalar‐valued coupled equations, and the consistent tangent modulus is derived in a quite versatile form by introducing a set of fourth‐rank constitutive parameters into the discretized evolution rule of back stress. The constitutive model is, then, implemented in a finite element program and applied to a lead‐free solder joint analysis. It is demonstrated that the implicit integration is very accurate if the multilinear kinematic hardening model of Ohno and Wang is employed, and that the consistent tangent modulus certainly affords quadratic convergence to the Newton–Raphson iteration in solving nodal force equilibrium equations. Copyright © 2003 John Wiley & Sons, Ltd.     

Numerical simulation of slider dynamics during slider–disk contact

In this paper, the dynamic behavior of pico slider in contact with the disk was calculated. The analysis model consists of a simplified suspension model, an air bearing model, and a slider–disk contact model. The contact model consists of two elements. One is surface roughness model measured by Atomic Force Microscope (AFM) and the other is micro-waviness model. The dynamic behaviors of the tri-pad slider are calculated at several rotation speeds to investigate slider vibration modes during slider–disk contact. The slider oscillation frequency depends on the rotation speed and it saturates about twice as much as eigen frequency of air bearing pitch mode.     

智能化劳厄定向法

提出了晶体劳厄定向的智能化方法；简述了有关的Ｘ射线衍射理论、数学模型和运行步骤；讨论了该方法的可靠性和实用性．     

关于混凝土钻芯取样法有关标准的讨论

本文对国内不同行业有关混凝土钻总取样方法的标准进行了讨论，供月行在使用和修订相应标准时参考。     

紧凑式轧机变形规程优化设计

本文从紧凑式轧机的轧制变形特点出发,分析了其变形规程设计的主要特点和方法,讨论了限制其道次变形量的基本因素,给出了优化设计的目标函数和约束条件。指出,类似这种具有复杂约束的轧制变形问题采用混合罚函数法处理更为有效,并成功地采用该方法进行了变形规程的试设定。     

用分解法编制轴类零件图程序

采用分解法编写轴类零件程序，即将具有典型结构的轴分解成若干部分，把每一部分编成通用子程序，连同尺寸标注子程序、表面粗糙度子程序、剖面线子程序、尺寸公差及形位公差子程序等一并存贮在程序库中，需要时一一调用。