Fast‐scale bifurcation in power‐factor‐correction buck‐boost converters and effects of incompatible periodicities

In this paper, we derive the discrete‐time model for the power‐factor‐correction (PFC) buck‐boost converter in terms of a stroboscopic switching map. Fast‐scale instability is analysed through a fold diagram, which exposes the periodicity of the operation as well as the locations of the critical phase angles of the line voltage at which instability begins to occur along a half‐line cycle. The asymmetrical locations of the critical phase angles along a half‐line cycle is explained in terms of ‘under‐developed’ bifurcation. Border collision bifurcations are observed and analysed in detail. Copyright © 2006 John Wiley & Sons, Ltd.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

侧槽溢洪道出口控制水深计算

本文推导侧槽段的总水头损失公式,从而求得侧槽末端的断面能量和水深,并以此水深做为侧槽的控制水深.根据水工模型试验资料验证,本文提出的计算方法是可行的.     

高性能小型扫描器

本文讨论了一种高性能小型扫描器的基本原理及扫描时序变换。对采用该小型扫描器的热成像系统也作了详细的介绍。该小型扫描器可满足多种用途。     

攀钢转炉炼钢用碳化硅提温的试验研究

低品位碳化硅是转炉炼钢的有效提高温剂。工业性试验结果表明，碳化硅加入８．０ｋｇ／ｔ钢水提温４０．３－７０．３℃（平均４８．４℃）；渣中ＴＦｅ降低１．３％；加提温剂有利于转炉内造渣脱硫和碱少炉渣对耐火砖的侵蚀。文中还给出了攀钢转炉半钢冶炼铸用钢不水时加与不加碳化硅的ｔλ，［Ｃ］λ区域。     

FINITE ELEMENT ANALYSIS OF THE FLOW INDUCED BY ROTATING BLADES IN AN INCOMPRESSIBLE VISCOUS FLUID

Aerodynamic loads on a multi-bladed helicopter rotor in hovering flight were calculated by solving the three-dimensional incompressible Navier-Stokes equations. The rotor wake effects were accounted by the correction of local geometric angle of attack according to a free-wake modeling in addition to an empirical modification for the tip flow effect. The validity and efficiency of the present method were verified by the comparisons between numerical results and experimental data.     

Modeling of a power electronic converter for EMC in the conduction emission frequency band

With the advancement of high‐frequency switching devices, electromagnetic interferences (EMI) have become problems in power electronic converter designs. It is necessary for an electromagnetic compatibility (EMC) design to prospect and consider its possible EMI levels. This paper describes how to compute effects from a power converter to an object point to reduce conduction EMI noises effectively by an appropriate design. Modeling techniques for converter elements are discussed for a model in the conduction emission frequency band by the parameter tuning method and for line constants by an analytical derivation. Then a derived model is simulated for harmonic distributions of loop currents and their magnetic fields. © 2002 Scripta Technica, Electr Eng Jpn, 139(1): 44–50, 2002: DOI 10.1002/eej.1145     

转子系统热膨胀状态下固有横振频率

把转子的惯性力看成作用在轴上的外力,采用新的非线性渐近法研究热膨胀对转子系统固有横振频率的影响.     

静电驱动悬臂梁数模转换器设计、分析与模拟

提出了一种新型的微电子机械数模转换器 (MEMDAC)———静电驱动悬臂梁数模转换器 .与传统的静电驱动悬臂梁执行器相比 ,新的结构能更精确地控制梁的挠度 .文中给出了此MEMDAC的设计、分析和模拟过程 .有限元(FEA)分析表明此MEMDAC的最大输出位移为 1 5 1μm ,分辨率为 0 1μm ,其最大非线性误差为 0 0 3μm .