Continuous electromagnetic separation of inclusion from aluminum melt using alternating current

A novel scheme about the continuous electromagnetic purification of aluminum melt was put forward based on the utilization of a square separation pipe and a 50 Hz alternating current to produce electromagnetic force. It is experimentally found that with electrical current of 400 A/cm^2, it takes only 10 s to remove 95% inclusion from aluminum melt. Comprehensive numerical simulations were carried out to investigate the dynamics mechanisms behind the process. The results show that the removal of inclusion is attributed to the cooperative effects of electromagnetic buoyancy and the secondary flow induced by the rotational electromagnetic force, and the removal efficient increases with the size of inclusion and the electrical current imposed. Theoretical predictions on the distribution and removal efficiency of inclusion were supported by the experiments.     

用扩冲法修复凹形护环的新工艺

详细介绍了用扩冲法对液压胀形出现凹形的护环进行修复的方法。实践证明,扩冲法修复护环简单、经济、实用。     

护环液压胀形法的新发展及外补液胀形法的生产应用

本文论述了现有液压胀形法生产护环所存在的不足,介绍了新一代液压胀形工艺即外补液胀形的原理、优点,以及在我国首次生产应用中所显示出的明显的技术经济效益。     

THEORETICAL INVESTIGATION ON BY-ONLY-CURRENT ELECTROMAGNETIC SEPARATION OF INCLUSION FROM MOLTEN METALS

The electromagnetic field under applied AC and DC current in round and rectangular pipe was systematically investigated, then a concept of "equivalent current density" was proposed for evaluating the inhomogeneous electromagnetic pinch force, and the mono-component removal efficiency and the overall removal efficiency of inclusion were formulated. It is founded that flat pipe is superior to round pipe for the electromagnetic removal of inclusion, and DC current can get a higher removal efficiency than A C current due to absence of skin phenomenon. Under usual condition, a removal efficiency of 52% for 10μm inclusion or more than 92% for 20μm inclusion can be achieved by imposing a current density of 3×106A/m2 in a flat pipe.     

磁性纤维随机混合媒质等效电磁参数的计算

为计及强散射偶极子间的相互作用,引入参量εh和μh,利用广义多重散射理论及MATLAB计算机软件对在2 GHz～18 GHz频率下的体积占空比为8%的铁纤维随机混合媒质等效磁导率的实验值进行曲线的拟合,导出了耦合系数εh和μh,并在此基础上,对体积占空比分别为30%和20%的铁纤维随机混合媒质等效磁导率进行了计算,计算结果与实验吻合良好.     

水平电磁连铸空心铜管坯组织和性能研究

提出在中试水平的空心铜管坯水平连铸过程中施加工频电磁场,分析其对铜管坯组织和性能的影响.结果表明：与未施加电磁场时相比,施加电流强度为140A的工频电磁场后,水平连铸空心铜管坯的组织显著细化,平均晶粒度由未施加磁场时的3.1提高到8.3,周向组织均匀性也得到明显改善;抗拉强度提高40%左右,延伸率提高50%左右.     

国内弧焊设备电磁兼容性研究进展

焊弧设备的电磁兼容性问题日益突出，受到越来越多的关注。针对我国的实际情况，对国内弧焊设备的研究现状进行了综合分析，同时指出了今后的研究方向。     

A NEW ELECTROMAGNETIC IMAGING SCHEME

ＡＮＥＷＥＬＥＣＴＲＯＭＡＧＮＥＴＩＣＩＭＡＧＩＮＧＳＣＨＥＭＥ①ＺｈａｎｇＲｏｎｇｆｅｎｇ，ＨｅＪｉｓｈａｎＣｏｌｅｇｅｏｆＲｅｓｏｕｒｃｅ，ＥｎｖｉｒｏｎｍｅｎｔａｎｄＣｉｖｉｌＥｎｇｉｎｅｒｉｎｇ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙｏ...     

工艺参数对电磁铸造铝板坯温度场的影响

采用数值方法模拟电磁铸造过程的温度场，详细讨论了各种工艺参数，如宽厚比，浇注温度，铸造速度，冷却水量，喷水位置，喷水孔分布，感应热等对铝板坯凝固过程和温度场分布的影响规律，为电磁铸造工艺参数设计提供可靠依据。     

NUMERICAL SIMULATION OF ALTERNATIVE HORIZONTAL LEVITATION ELECTROMAGNETIC CONTINUOUS CASTING（Ⅱ）

ＮＵＭＥＲＩＣＡＬＳＩＭＵＬＡＴＩＯＮＯＦＡＬＴＥＲＮＡＴＩＶＥＨＯＲＩＺＯＮＴＡＬＬＥＶＩＴＡＴＩＯＮＥＬＥＣＴＲＯＭＡＧＮＥＴＩＣＣＯＮＴＩＮＵＯＵＳＣＡＳＴＩＮＧ（Ⅱ）￥ＺｈｕＳｈｏｕｊｕｎ；ＲｅｎＺｈｏｎｇｍｉｎｇ；ＤｅｎｇＫａｎｇ；Ｊｉａｎ...