Phase equilibria of the ternary Al-Cu-Ni system and interfacial reactions of related systems at 800 °C

A series of Al-Cu-Ni alloys of various compositions were made and annealed at 800 °C. The equilibrium phases were studied by metallography, X-ray diffraction (XRD) analysis, and electron probe microanalysis. The isothermal section of the ternary Al-Cu-Ni system at 800 °C was then determined based on these experimental results and the available phase relationship knowledge of the three constituent binary systems. No ternary compound was found. All three phases, AlNi₃, AlNi, and Al₃Ni₂, have very high ternary solubility, especially the AlNi phase, which almost reaches the binary Al-Cu side. However, no continuous solid solution was formed between the AlNi phase and any of the binary Al-Cu phases. Interfacial reactions of Al/Ni, Al/Cu, Al-Cu/Ni, and Al-Ni/Cu at 800 °C were investigated by using reaction couple techniques. The results showed that Al₃Ni and Al₃Ni₂ phases were formed in the Al/Ni couples; β-AlCu₄, γ ₁-Al₄Cu₉, and ɛ ₂-Al₂Cu₃ phases were formed in the Al/Cu couples. As for the results in the Al-2 at. pct Ni/Cu, Al-5 at. pct Ni/Cu, and Al-2 at. pct Cu/Ni, Al-4.5 at. pct Cu/Ni, and Al-6 at. pct Cu/Ni were similar to those in the binary Al/Cu and Al/Ni couples, respectively. A different reaction path was found in the Al-7.5 at. pct Cu/Ni couples, and an AlNi solid solution layer was formed instead of the Al₃Ni and Al₃Ni₂ phases.     

硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。     

加强和改进施工企业党组织建设的途径

推进施工企业党组织的建设必须与时俱进,坚持一岗双责、两个融合、三个同步、四个同时,创新工作思路、工作机制、工作方法和工作方式。把贯彻落实“三个代表”重要思想,作为检验工作成效的根本标准。     

Analysis on the effectiveness of the 20-H rule for printed-circuit-board layout to reduce edge-radiated coupling

This paper presents the quantified study of the electromagnetic radiation mechanism of the 20-H rule using a numerical approach that has not yet been systematically addressed. The 20-H rule is a rule-of-thumb layout technique recommended to minimize radiated fields propagating from the edges of a printed circuit board (PCB) coupling onto nearby structures. Propagating electromagnetic fields may corrupt adjacent cable assemblies, sheet metal enclosures, and aperture openings. The magnitude of this design rule is investigated using the full-wave finite-difference time-domain (FDTD) method. An analysis on whether benefits exist from use of this rule is examined and under what conditions the rule is valid when correctly implemented. The purpose of this paper is to provide insight into the validity of the 20-H rule, recognizing that every PCB will have different simulation results. FDTD is used to capture a snapshot view of field propagation. This view allows one to determine the validity of the 20-H rule at a single point of time within a dynamic structure and what may be expected when digital components are finally added to a PCB assembly, which generally negates simulated results.     

An experimental study of carrier heating on channel noise in deep-submicrometer NMOSFETs via body bias

In this paper, RF noise in 0.18-mum NMOSFETs concerning the contribution of carrier heating and hot carrier effect is characterized and analyzed in detail via a novel approach that modulates the channel carrier heating and number of hot carriers using body bias. We confirm qualitatively a negligible role of hot carrier effect on the channel noise in deep-submicrometer MOSFETs. For a device under reverse body bias (V_b), even though the increase in hot carrier population is clearly characterized by dc measurements, the device high-frequency noise is found to be irrelevant to the increase in the channel hot carriers. Experimental results show that the high-frequency noise is slightly reduced with the increase in |V_b|, and can be qualitatively explained by secondary effects such as the suppression of nonequilibrium channel noise and substrate induced noise. The reduction of NF_min and R_n with the increase in |V_b| may provide a possible methodology to finely adjust the device high-frequency noise performance for circuit design     

Effect of Synergistic Anticorrosion Treatments on Cycling Stability of Mg-Based Hydrogen Storage Electrode

In this paper, any two of the three anticorrosion agents, that is emulsifier (OP-10), soluble glass (Na2O·nSiO2) and glycerin (C3H8O3), were treated simultaneously on the surface of amorphous (a-) MgNi+5% Ml2Mg17 (Ml denotes the lanthanum-rich mish metal) electrode and the electrolyte. Effect of the synergistic anticorrosion treatment on charging/discharging cycle stability of the electrode was investigated. Contrasted with single treatment method, the cycling stability of the electrodes was further improved. The desirable synergistic anticorrosion method was that the electrode was treated by the soluble glass, and that OP-10 was added into the electrolyte. The cyclic voltammogram (CV) results of the electrode show clearly that the anticorrosion agent can change the electrochemical activity and mechanism of the electrode. The concentration of the anticorrosion agent in the electrolyte treated by the synergistic anticorrosion method was also investigated. The appropriate concentration of the anticorrosion agents in the electrolyte is 0.143%.     

尿素解吸废液及甲醇残液联合处理工艺的应用

安阳化学工业集团公司(以下简称安化集团)现有2套200 kt/a尿素装置及1套60 kt/a甲醇装置.尿素及甲醇装置在生产过程中会产生大量的尿素解吸废液和甲醇残液,废液中的氨氮(NH3-N)含量和化学需氧量(CODCr)较高,给该公司废水的达标排放带来很大压力.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.