Influence of LiBO2 addition on the microstructure and lithium-ion conductivity of Li1+xAlxTi2−x(PO4)3(x = 0.3) ceramic electrolyte

Concerning the safety problems of conventional Li-ion batteries with liquid electrolytes, it is crucial to develop reliable solid-state electrolytes with high ionic conductivity. Li_1+xAl_xTi_2?x(PO₄)₃ (LATP, x = 0.3) is regarded as one of the most promising solid electrolytes due to its high ionic conductivity and excellent chemical stability to humidity.Herein, a new strategy is proposed for improving the sintering behavior and enhancing the ionic conductivity of LATP by using LiBO₂ as the sintering aid via liquid phase sintering. The as-prepared sample LATP with homogeneous microstructure and high relative density of 97.1% was successfully synthesized, yielding high total ionic conductivity of 3.5 × 10^?4 S cm^?1 and low activation energy of 0.39 eV at room temperature. It was found that the addition of LiBO₂ could effectively enhance the densification and increase the ionic conductivity of LATP electrolyte, proving an effective way to synthesis LATP ceramics by a simple and reliable route.     

Structural,mechanical, and electrical properties of carbon nanoparticles synthesized from diesel

We studied the elemental analysis, structural morphology, mechanical, and electrical properties of carbon nanoparticles synthesized from diesel. The spherical carbon particle size in the range of about 10 to 80 nm in diameter was observed in scanning electron microscope (SEM) studies that were identified by Atomic force microscopy (AFM) study as an aggregation of carbon particles of average size 2.5 nm. The surface rms of carbon nanoparticle thin film (CNTF) was measured directly by AFM and found 0.22 nm. The Derjaguin–Muller–Toporov (DMT) elastic modulus of carbon nanoparticles (CNPs) was measured by PeakForce QNM mode of AFM. The minimum and maximum elastic modulus was measured of 0.40 GPa and 43.89 GPa, respectively. The resistivity, conductivity, magneto resistance, mobility, and average Hall co-efficient were measured by “Ecopia Hall-effect measurement system” by four-point Van der Pauw approach at ambient condition. We demonstrated I–V characteristic at the Indium/CNTF thin film interface, which is accompanied by rectifying behavior.     

Synthesis and characterization of dextrin derivatives by heterogeneous esterification

A series of fully-acylated dextrin esters (DS = 3) with varying side-chain lengths (C2–12) were synthesized by heterogeneous esterification using trifluoroacetic anhydride/carboxylic acid. The influence of side-chain lengths on structure and properties of dextrin esters were investigated by structural, thermal, mechanical and hydrophobic analysis. The thermal stability of dextrin was enhanced by esterification, presenting ca. 40–60 °C higher decomposition temperatures than that of neat-dextrin. The transition temperatures of melting and crystallization were not observed for all dextrin esters because they were amorphous polymers. The glass transition temperature (T_g) was not observed in dextrin but was observed in dextrin esters. As increasing side-chain length, T_gs of dextrin esters decreased ranged from 162.2 °C (C2) to 49.2 °C (C12). Colorless and transparent dextrin ester films were prepared to measure the film properties. Tensile strength of dextrin ester films tended to decrease with increasing side-chain lengths, whereas the elongation at break increased. And, dextrin ester films showed significantly increased hydrophobicity with a contact angle of up to 102° (C12).     

Development of Sensor and Control Systems of a Wearable Robot to Walk on a Step

The goal of our study is to develop a system for walking on a step using a wearable robot. Our system consists of (1) sensing of a step from the movement of the walker, (2) detection of the foot placement state related to the step, and (3) generation of gait patterns of climbing and stepping down for the step. In the generation of gait patterns for the step, toe trajectories are generated according to the height of the step to avoid collision of the swinging leg with the step. The hip trajectory is generated by an optimization technique that minimizes the sum of the joint angular jerk of the robot subject to constraints on the hip position and the velocity at toe liftoff. Each joint angle trajectory is calculated from the generated trajectories by means of inverse kinematic equations. We investigated the feasibility of the proposed sensor and control systems for two steps with different heights.     

Ozonation of N-Nitrosamines in the Reverse Osmosis Concentrate from Water Recycling Applications

This study aims to evaluate the performance of ozone treatment for removing N-nitrosamines from reverse osmosis (RO) concentrate in water recycling applications. In the absence of any N-nitrosamine precursors, the destruction efficiency of N-nitrosamines was dependent on their molecular weight or the length of the alkyl chain in their molecular structure. Experiments conducted with RO concentrate showed that ozonation could lead to the formation of N-nitrosodimethylamine (NDMA) and N-nitrosodiethylamine (NDEA), resulting in an increase in concentrations of these N-nitrosamines. Nevertheless, ozonation was effective for destruction of N-nitrosamines with molecular weight greater than that of NDEA (102 g/mol).     

High‐temperature latent heat storage technology to utilize exergy of solar heat and industrial exhaust heat

Latent heat storage (LHS) using phase change materials is quite attractive for utilization of the exergy of solar energy and industrial exhaust heat because of its high‐heat storage capacity, heat storage and supply at constant temperature, and repeatable utilization without degradation. In this article, general LHS technology is outlined, and then recent advances in the uses of LHS for high‐temperature applications (over 100 °C) are discussed, with respect to each type of phase change material (e.g., sugar alcohol, molten salt, and alloy). The prospects of future LHS systems are discussed from a principle of exergy recuperation. In addition, the technologies to minimize exergy loss in the future LHS system are discussed on the basis of the thermodynamic analysis by ‘thermodynamic compass’. Copyright © 2016 John Wiley & Sons, Ltd.     

Improvement in thermal endurance of D-mannitol as phase-change material by impregnation into nanosized pores

This paper describes the control of the melting point and improvement of the thermal endurance of D-mannitol (melting point T_m = 440 K) as a phase-change material (PCM) by vacuum impregnation of the PCM into nanosized pores of porous SiO₂ grains. First, we examined the effects of the average pore size (D_P) of porous SiO₂ on T_m and latent heat (L) of PCM/SiO₂ composites. Second, we investigated the thermal endurance of the composites using constant temperature kinetics based on L of the PCM and composites. Third, we performed cyclic tests of melting and freezing on the composite to evaluate leakage of the PCM. Thermophysical properties of the samples were measured by differential scanning calorimetry, and the following results were obtained: (1) The impregnation ratio of the composites was 0.91–0.99; therefore, almost all pores were completely filled with the PCM. (2) T_m shifted to lower temperature with smaller D_P, reaching 413 K in case of the PCM/SiO₂ composite with a D_P of 11.6 nm (3) T_m was derived as a function of D_P from the Gibbs–Thomson equation taking into account the existence of a nonfreezing layer on the surface of the pore wall. (4) The duration of thermal degradation of the PCM/SiO₂ composite with D_P = 11.6 nm was three times longer than that of the pure PCM at a temperature that is 10 K more than each melting point. (5) The PCM/SiO₂ composite with D_P = 11.6 nm can use as a shape-stable PCM composite without leakage of PCM.     

Measurement of High-Temperature Elastic Properties of Ceramics Using a Laser Ultrasonic Method

Young's modulus and Poisson's ratio of SiC ceramics at temperatures >1400°C were obtained using a laser ultrasonics method that included a Fabry-Pérot interferometer (LUFP). At temperatures <1000°C, Young's modulus and Poisson's ratio measured using the LUFP method agreed well with those measured using standard contact methods, such as the resonance method and the ultrasonic pulse method. These results showed that the LUFP method is a powerful tool for measuring high-temperature elastic properties of advanced ceramics in a noncontact manner.