Similar to EDM, in micro-EDM, intense heat is generated between the workpiece and tool electrode by the discharge through a dielectric medium to result in the formation of a microcrater that is much smaller in size. In this study, a single-spark generator has been developed to study the erosion characteristics from the microcrater size. Using a simple heat transfer model, the efficiency at different discharge condition is also deduced. It is found that at lower-energy (<50 μJ) discharges, the energy required to remove the unit volume of material, defined as the specific energy, is found to be much less than that at higher-energy discharges. Additionally, the ratio of the standard deviation to the measured microcrater size is found to be lower at lower discharge energy, indicating greater consistency in shape and size when the discharge occurs at lower energy. The fundamental erosion mechanism of material is discussed by considering melting and evaporation phenomena using theoretical modeling. The average efficiency of erosion, when estimated to be due primarily to melting or evaporation alone, is found to be up to an order of magnitude higher at lower-energy discharges than that at higher-energy discharges. 相似文献
In order to determine the deformation modes in AZ31 magnesium alloy at room temperature, computer simulations of deformation
texture development and calculation of formability have been carried out. The simulation results were compared with the measured
texture results. Based on agreement between the experiments and simulations the active deformation modes were determined.
A Visco Plastic Self Consistent model was employed for the simulation of plastic deformation. Simulations and experiments
were performed for different initial textures. The goal of the study was to develop the understanding of deformation texture
evolution and its effects on mechanical properties of magnesium, with an ultimate goal of improving room temperature formability
of magnesium alloys.
This article was presented at Materials Science & Technology 2006, Innovations in Metal Forming symposium held in Cincinnati,
OH, October 15-19, 2006. 相似文献
In this paper, a novel pyramid coding based rate control scheme is proposed for video streaming applications constrained by a constant channel bandwidth. To achieve the target bit rate with the best quality, the initial quantization parameter (QP) is determined by the average spatio-temporal complexity of the sequence, its resolution and the target bit rate. Simple linear estimation models are then used to predict the number of bits that would be necessary to encode a frame for a given complexity and QP. The experimental results demonstrate that the proposed rate control scheme significantly outperforms the existing rate control scheme in the Joint Model (JM) reference software in terms of Peak Signal to Noise Ratio (PSNR) and consistent perceptual visual quality while achieving the target bit rate. Finally, the proposed scheme is validated through experimental evaluation over a miniature test-bed.
Limb repositioning is necessary for individuals with severe physical disabilities to sustain muscle strength and prevent pressure sores. As robotic technologies become ubiquitous, these tools offer promise to support the repositioning process. However, research has yet to focus on ways in which individuals with severe physical disabilities can control robots for these tasks. This paper presents a study that examines the needs and attitudes of potential users with physical disabilities to control a robotic aid for limb repositioning. Subjects expressed interest in using brain–computer interface (BCI) and speech recognition technologies for purposes of executing robotic tasks. The performance of four subjects controlling arm movements on an avatar through the keyboard, mouse, BCI, and Dragon NaturallySpeaking speech recognition was evaluated. Although BCI and speech technologies may limit physical fatigue, more challenges were faced using BCI and speech conditions compared to the keyboard and mouse. This research promotes accessibility into mainstream robotic technologies and represents the first step in the development of a robotic prototype using a BCI and speech recognition technologies for limb repositioning. 相似文献
Since the 1950s, 8.3 billion tonnes (Bt) of virgin plastics have been produced, of which around 5 Bt have accumulated as waste in oceans and other natural environments, posing severe threats to entire ecosystems. The need for sustainable bio-based alternatives to traditional petroleum-derived plastics is evident. Bioplastics produced from unprocessed biological materials have thus far suffered from heterogeneous and non-cohesive morphologies, which lead to weak mechanical properties and lack of processability, hindering their industrial integration. Here, a fast, simple, and scalable process is presented to transform raw microalgae into a self-bonded, recyclable, and backyard-compostable bioplastic with attractive mechanical properties surpassing those of other biobased plastics such as thermoplastic starch. Upon hot-pressing, the abundant and photosynthetic algae spirulina forms cohesive bioplastics with flexural modulus and strength in the range 3–5 GPa and 25.5–57 MPa, respectively, depending on pre-processing conditions and the addition of nanofillers. The machinability of these bioplastics, along with self-extinguishing properties, make them promising candidates for consumer plastics. Mechanical recycling and fast biodegradation in soil are demonstrated as end-of-life options. Finally, the environmental impacts are discussed in terms of global warming potential, highlighting the benefits of using a carbon-negative feedstock such as spirulina to fabricate plastics. 相似文献
In this work, a deep learning (DL)-based massive multiple-input multiple-output (mMIMO) orthogonal frequency division multiplexing (OFDM) system is investigated over the tapped delay line type C (TDL-C) model with a Rayleigh fading distribution at frequencies ranging from 0.5 to 100 GHz. The proposed bi-directional long short-term memory (Bi-LSTM) channel state information (CSI) estimator uses online learning during training and offline learning during the practical implementation phase. The design of the estimator takes into account situations in which prior knowledge of channel statistics is limited and targets excellent performance, even with limited pilot symbols (PS). Three separate loss functions (mean square logarithmic error [MSLE], Huber, and Kullback–Leibler Distance [KLD]) are assessed in three classification layers. The symbol error rate (SER) and outage probability performance of the proposed estimator are evaluated using a number of optimization techniques, such as stochastic gradient descent (SGD), momentum, and the adaptive gradient (AdaGrad) algorithm. The Bi-LSTM-based CSI estimator is trained considering a specific number of PS. It can be readily seen that by incorporating a cyclic prefix (CP), the system becomes more resilient to channel impairments, resulting in a lower SER. Simulations show that the SGD optimization approach and Huber loss function-trained Bi-LSTM-based CSI estimator have the lowest SER and very high estimation accuracy. By using deep neural networks (DNNs), the Bi-LSTM method for CSI estimation achieves a superior channel capacity (in bps/Hz) at 10 dB than long short-term memory (LSTM) and other conventional CSI estimators, such as minimum mean square error (MMSE) and least squares (LS). The simulation results validate the analytical results in the study. 相似文献
The Journal of Supercomputing - This study offers a neural network-based deep learning method for energy optimization modeling in electric vehicles (EV). The pre-processed driving cycle is... 相似文献
Cryorolling is a severe plastic deformation (SPD) process used to obtain ultrafine-grained aluminum alloy sheets along with higher strength and hardness than in conventional cold rolling, but it results in poor formability. An alternative method to improve both strength and formability of cryorolled sheets by warm forming after cryorolling without any post-heat treatment is proposed in this work. The formability of cryorolled AA6061 Al alloy sheets in the warm working temperature range is characterized in terms of forming limit diagrams (FLDs) and limiting dome height (LDH). Strain distributions and thinning in biaxially stretched samples are studied. Hardness of the formed samples is correlated with ultimate tensile strength to estimate post-forming mechanical properties. The limit strains and LDH have been found to be higher than in the case of the conventional processing route (cold rolled, annealed and formed at room temperature), making this hybrid route capable of producing sheet metal parts of aluminum alloys with high strength and formability. In order to combine the advantages of enhanced formability and better post-forming strength than the conventional cold rolled and annealed sheets, warm forming at 250°C has been found to be suitable for this alloy in the temperature range that has been studied. 相似文献