Synthesis and Characterization of Eu3+‐Doped Transparent Glass–ceramics Containing Nanocrystalline SrIINbIVO3

The glass–ceramics containing a rarely achievable nanocrystalline Sr^IINb^IVO₃ phase in the 53.75SiO₂–18.25K₂O–9Bi₂O₃–9SrO–9Nb₂O₅–0.5CeO₂–0.5Eu₂O₃ (mol%) glass system were prepared by the melt‐quench technique followed by a two‐stage controlled heat treatment. The unusual oxidation state of Nb in Sr^IINb^IVO₃ crystal is 4+ and upon heat treatment of the samples at lower temperature of 500°C for several hours, the glass composition and chemical environment around Nb ions played a key role for the formation of Sr^IINb^IVO₃ in the glass–ceramics. The microstructure of the glass–ceramics was studied using TEM and FESEM. The TEM images advocate 10–40 nm crystallite size of Sr^IINb^IVO₃. FTIR study confirms that all the samples consist of SiO₄, BiO₃, BiO₆, and NbO₆ structural units. The refractive index at different wavelengths was found to vary in the range 1.7105–1.7905 and increase with increase in heat‐treatment time. The luminescence spectra of Eu³⁺‐doped glass and glass–ceramics were recorded at 465 nm excitation wavelength and the luminescence intensity is found to be increased with heat‐treatment time due to increase in crystallinity. The high intensity ratio of ⁵D₀→⁷F₂ to ⁵D₀→⁷F₁ indicates that the Eu³⁺‐doped nanocrystalline Sr^IINb^IVO₃ glass–ceramics are promising candidate materials as red‐light source.     

Thermal,Structural, and Enhanced Photoluminescence Properties of Eu3+‐doped Transparent Willemite Glass–Ceramic Nanocomposites

The precursor glass in the ZnO–Al₂O₃–B₂O₃–SiO₂ (ZABS) system doped with Eu₂O₃ was prepared by the melt‐quench technique. The transparent willemite, Zn₂SiO₄ (ZS) glass–ceramic nanocomposites were derived from this precursor glass by a controlled crystallization process. The formation of willemite crystal phase, size, and morphology with increase in heat‐treatment time was examined by X‐ray diffraction (XRD) and field‐emission scanning electron microscopy (FESEM) techniques. The average calculated crystallite size obtained from XRD is found to be in the range 18–70 nm whereas the grain size observed in FESEM is 50–250 nm. The refractive index value is decreased with increase in heat‐treatment time which is caused by the partial replacement of ZnO₄ units of ZS nanocrystals by AlO₄ units due to generation of vacancies. Fourier transform infrared (FTIR) reflection spectroscopy was used to evaluate its structural evolution. Vickers hardness study indicates marked improvement of hardness in the resultant glass‐ceramics compared with its precursor glass. The photoluminescence spectra of Eu³⁺ ions exhibit emission transitions of ⁵D₀→⁷F_j (j = 0, 1, 2, 3, and 4) and its excitation spectra show an intense absorption band at 395 nm. These spectra reveal that the luminescence performance of the glass–ceramic nanocomposites is enhanced up to 17‐fold with the process of heat treatment. This enhancement is caused by partitioning of Eu³⁺ ions into glassy phase instead of into the willemite crystals with progress of heat treatment. Such luminescent glass–ceramic nanocomposites are expected to find potential applications in solid‐state red lasers, phosphors, and optical display systems.     

Local cloning of multipartite entangled states

No cloning theorem is a very fundamental issue in quantum mechanics. But the issue is much more involved if we consider quantum state shared among two or more than two parties and allow only local operation and classical communication. In the context of the fact that no known bipartite entangled state can be cloned by local operation and classical communication (LOCC) without assistance of extra entangled state, the cloning of unknown orthogonal entangled state becomes meaningful when there is some supply of free entanglement. With restriction on supply of free entanglement, various cases have been studied. In this paper, we try to give an overview of the subject and results that have been obtained across the literature along with a new result on probabilistic LOCC cloning of four Bell states.     

Bridging fault detection in cluster based FPGA by using Muller C element

In this work, we propose a testing technique for detecting single stuck-at and bridging faults in the interconnects of the cluster based FPGA. The presence of the feedback-bridging fault, race and glitch poses major challenges to the detection of the fault. The feedback bridging fault has a high ingredient of delay dependent properties due to the variation of the feedback path delay. So we have exploited the concept of asynchronous logic in order to detect the fault. We configure the block under test (BUT) with a pseudo delay independent asynchronous element known as Muller C element. The novelty of this scheme lies in the fact that, it can detect the stuck-at and bridging fault including the feedback bridging fault by a single test configuration. The Xilinx Jbits 3.0 API (Application Program Interface) is used to implement the BISTER (Built-in-self-tester) structure in the FPGA. In comparison to the traditional FPGA development tool (ISE), ‘Jbits’ gives more controllability for which the partial run time reconfiguration of the FPGA is easily achieved.     

Early Stages of Calcium Phosphate Formation on Bioactive Borosilicate Glass in Aqueous Phosphate Solution

The conversion of bioactive glass to a calcium phosphate material, typically hydroxyapatite (HA), by solution–precipitation reactions in aqueous phosphate solution, has been commonly reported. This paper describes the structural and compositional characteristics of the calcium phosphate material formed during the early-stage conversion (<5 h) of a borosilicate glass (designated H12) in aqueous phosphate solution. Disks of H12 glass were reacted with 0.25 M K₂HPO₄ solution with a starting pH=7.0 at 37°C. The structure and composition of the product layer were characterized using thin film X-ray diffraction, scanning electron microscopy, and Fourier transform infrared reflectance spectroscopy. For reaction times <5 h, the results indicated the formation of brushite (CaHPO₄·2H₂O) with coarse, plate-like crystals. In comparison, the formation of HA with small needle-like crystals was found at later times. This early-stage formation of brushite has not been reported in previous studies of converting bioactive silicate and borate glasses in aqueous phosphate solution.     

Effects of various process parameters on struvite precipitation kinetics and subsequent determination of rate constants.

In this paper, struvite (MgNH(4)PO(4).6H(2)O) precipitation kinetics were studied with different operating conditions (varying supersaturation, pH, Mg:P ratio, degree of mixing and seeding conditions) and relevant rate constants were determined by fitting a slightly modified first-order kinetic model to the experimental data obtained. The rate of change of ortho-P concentration in the bulk solutions increases with increasing supersaturation ratio. The estimated rate constants are 2.034, 1.716 and 0.690 hr(-1) for the supersaturation ratio of 9.64, 4.83, and 2.44, respectively. Kinetic parameters were also evaluated for the Mg:P ratio between the ranges of 1.0 and 1.6, indicating higher phosphorus removal efficiency with increasing Mg:P ratio. The rate constants were found to be 0.942, 2.034 and 2.712 hr(-1) for Mg:P ratios of 1.0, 1.3 and 1.6, respectively. The experimental observations for kinetic study of struvite precipitation with different stirrer speeds clearly show that the mixing intensity used had little effect on the intrinsic rate constants. K values found to be 2.034 and 1.902 h(-1) for 100 and 70 rpm, respectively. Seeding, with 250-500 microm of seed crystals during the struvite precipitation kinetics test, was found to have very little effect on the ortho-P removal.     

Microstructure Refinement of Sintered Alumina by a Two-Step Sintering Technique

For a few oxide ceramics, the use of an initial precoarsening step prior to densification (referred to as two-step sintering) has been observed to produce an improvement in the microstructural homogeneity during subsequent sintering. In the present work, the effect of a precoarsening step (50 h at 800°C) on the subsequent densification and microstructural evolution of high-quality alumina (Al2O3) powder compacts during constant-heating-rate sintering (4°C/min to 1450°C) was characterized in detail. The data were compared with those for similar compacts that were sintered conventionally (without the heat treatment step) and used to explore the mechanism of microstructural improvement during two-step sintering. After the precoarsening step, the average pore size was larger, but the distribution in pore sizes was narrower, than those for similar compacts that were sintered conventionally to 800°C. In subsequent sintering, the microstructure of the precoarsened compact evolved in a more homogeneous manner and, at the same density, the amount of closed porosity was lower for the compacts that were sintered by the two-step technique, in comparison to the conventional heating schedule. Furthermore, a measurably higher final density, a smaller average grain size, and a narrower distribution in grain sizes were achieved with the two-step technique. The microstructural refinement that was produced by the two-step sintering technique is explained in terms of a reduction in the effects of differential densification and the resulting delay of the pore channel pinch-off to higher density.     

Bioactive glass scaffolds for bone tissue engineering: state of the art and future perspectives

The repair and regeneration of large bone defects resulting from disease or trauma remains a significant clinical challenge. Bioactive glass has appealing characteristics as a scaffold material for bone tissue engineering, but the application of glass scaffolds for the repair of load-bearing bone defects is often limited by their low mechanical strength and fracture toughness. This paper provides an overview of recent developments in the fabrication and mechanical properties of bioactive glass scaffolds. The review reveals the fact that mechanical strength is not a real limiting factor in the use of bioactive glass scaffolds for bone repair, an observation not often recognized by most researchers and clinicians. Scaffolds with compressive strengths comparable to those of trabecular and cortical bones have been produced by a variety of methods. The current limitations of bioactive glass scaffolds include their low fracture toughness (low resistance to fracture) and limited mechanical reliability, which have so far received little attention. Future research directions should include the development of strong and tough bioactive glass scaffolds, and their evaluation in unloaded and load-bearing bone defects in animal models.