Microstructure and fatigue properties of hydroformed aluminum alloys 6063 and 5754

This study investigated the microstructure and fatigue properties of hydroformed sections of the 5754 and 6063 aluminum alloys. The second-phase particles in 6063-T7 are identified as a mixture of Al₁₂Fe₃Si and Al₉Fe₂Si₂, with a slightly higher fraction of the former. The constituent particles in the 5754 alloy are Al₄Mn-type hexagonal compounds, where Mn is partially substituted by various other elements, resulting in Al₄(Fe,Mn,Si,Cr). The results show that despite its lower yield strength, the hydroformed 5754 alloy has higher ultimate tensile strength, ductility, and, more importantly, higher fatigue resistance than the 6063 material. Both crystallographic stage I and noncrystallographic stage II cracking are found in the 6063-T7 samples, but only stage II cracking is observed in the 5754 alloy. This implies that the low fatigue strength of 6063-T7 is related to its relatively large grain size, resulting in rapid stage I crack propagation. The higher fatigue lives of the 5754 alloy compared to the 6063 alloy in both the low- and high-cycle life regimes are due to the increased fatigue-crack-initiation and propagation resistance of the 5754 alloy and its probable cyclic strain-hardening behavior.     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

To treat or not to treat: comparison of different criteria used to determine whether weight loss is to be recommended

Background  

Excess body fat is a major risk factor for disease primarily due to its endocrine activity. In recent years several criteria have been introduced to evaluate this factor. Nevertheless, treatment need is currently assessed only on the basis of an individual's Body Mass Index (BMI), calculated as body weight (in kg) divided by height in m². The aim of our study was to determine whether application of the BMI, compared to adiposity-based criteria, results in underestimation of the number of subjects needing lifestyle intervention.     

The relationship between bioelectrical impedance phase angle and subjective global assessment in advanced colorectal cancer

Background  

Bioelectrical Impedance (BIA) derived phase angle is increasingly being used as an objective indicator of nutritional status in advanced cancer. Subjective Global Assessment (SGA) is a subjective method of nutritional status. The objective of this study was to investigate the association between BIA derived phase angle and SGA in advanced colorectal cancer.     

Optimization of the magnetic circuit in the MFL inspection system for storage-tank floors

Magnetization is the key to inspection of a tank floor via the magnetic-flux-leakage (MFL) technique. In order to optimize the magnetic circuit of the MFL detector and obtain the best detection effects, the influences of the magnet size on the floor magnetization condition, the gap magnetic flux density, and the magnetic force were studied with the help of the finite element method (FEM) and the effects of some other parameters, such as the magnet pole spacing and pole-piece thickness, on the signal-to-noise ratio were analyzed. The simulation results indicate that variation of the magnet width affects the magnetization much more than variation of the magnet thickness and that the detector can reach a trade-off between the magnetization effects and the driving force when the magnet is about 30 mm thick and 40 mm wide. On condition that the floor has reached its magnetizing saturation, an increase in the magnet-pole spacing and the pole-piece thickness can improve the testing sensitivity and the signal-to-noise ratio. The text was submitted by the authors in English.     

Joint Measurements on Qubits and Cloning of Observables

Cloning of observables, unlike standard cloning of states, aims at copying the information encoded in the statistics of a class of observables rather then on quantum states themselves. In such a process the emphasis is on the quantum operation (evolution plus measurement) necessary to retrieve the original information. We analyze, for qubit systems, the cloning of a class generated by two noncommuting observables, elucidating the relationship between such a process and joint measurements. This helps in establishing an optimality criterion for cloning of observables. We see that, even if the cloning machine is designed to act on the whole class generated by two noncommuting observables, the same optimal performances of a joint measurement can be attained. Finally, the connection with state dependent cloning is enlightened.     

Semantische Informationsextraktion in medizinischen Informationssystemen

Zusammenfassung Dieser Artikel beschreibt einige Erfahrungen und typische Problemstellungen mit Textmining in der Medizin und gibt einen Einblick in aktuelle und zukünftige Herausforderungen in Forschung & Entwicklung. Interessant ist n?mlich, dass auch im ,,Multimedia-Zeitalter“ die meiste Information immer noch als ,,Text“ vorliegt. Mithilfe von statistischen und linguistischen Verfahren wird mit sogenannter ,,Textmining-Software“ versucht, aus Freitexten Information ,,heraus zu schürfen“ (deshalb ,,Textmining“). Allerdings ist es damit noch nicht genug. Der n?chste Schritt besteht darin, die Information sowohl nutzbar als auch brauchbar zu machen. Die jeweiligen End-Benutzerinnen und End-Benutzer müssen in die Lage versetzt werden, auf der Basis der gewonnenen Information deren Wissen zu erweitern. In unserem konkreten Fall sollen damit Entscheidungen im Rahmen ?rztlichen Handelns unterstützt werden. Probleml?sungen in diesem Bereich erfordern eine holistische Sicht- und Herangehensweise. Daher wird es immer wichtiger, Erkenntnisse aus Informatik und Psychologie zusammenflie?en zu lassen und auf systemischer Ebene technologisch umzusetzen.     

Relationships between urbanization and the oak resource of the Minneapolis/St. Paul Metropolitan area from 1991 to 1998

Urbanization was associated with loss and transformation of the oak forest in the Twin Cities (Minneapolis and St. Paul) metropolitan area (TCMA) over a recent 7-year interval. Between 1991 and 1998, urbanization increased based on several indicators: population density, area of developed land, and area of impervious surface—total impervious area and area within three classes of increasing degree of imperviousness (protected, affected, and degraded). We quantified relationships between changes in urbanization and changes in several parameters describing the oak forest at the scale of ecological subsection. Increased total and affected impervious area were strongly correlated with decreased area of oak forest when changes of the urbanization indicators and oak were expressed as percentages of the subsection area. Relationships were reversed when changes were expressed as percentages of the 1991 values. Increased population density was strongly correlated with increased loss in numbers and increased isolation of oak patches, but weakly correlated with loss of oak forest area. This is the first study to quantify relationships between changes in urbanization and changes in a specific forest cover type. Our results demonstrate complexities of urbanization impacts on a metropolitan forest resource, and highlight the importance of selected variables, spatial and temporal scales, and expressions of change when quantifying these relationships.     

Synthesis and Characterizations of Triphenylamine End-Functionalized Polymers via Reversible Addition-Fragmentation Chain Transfer Polymerization

A novel reversible addition-fragmentation chain transfer (RAFT) reagent bearing triphenylamine (TPA) group, 4-diphenylamino-dithiobenzoic acid benzyl ester (DDABE), was designed and synthesized. It was used in the RAFT polymerizations of styrene (St) and methyl acrylate (MA) to prepare end-functionalized polymers. The results of the polymerization showed that the RAFT polymerizations could be well controlled using DDABE as the RAFT agent. Number-average molecular weight (M_n,GPC) increased linearly with monomer conversion, and molecular weight distributions were relatively narrow (PDI< 1.50). The results of chain-extension reaction, ¹H NMR spectra and UV/Vis spectra confirmed that most of the polymers chains were end-capped by the functional triphenylamine (TPA) groups. The effect of feed molar ratios of St/DDABE/AIBN on polymerization was investigated.