Thermal Conductivity/Diffusivity of Silicon Carbide Whisker Reinforced Mullite

The thermal conductivity and diffusivity of silicon carbide whisker reinforced mullite was shown to increase with whisker content. This effect was much greater for vapor-liquid-solid (VLS) whiskers than for rice-hull (RH) whiskers. This suggests that the thermal conductivity for the VLS whiskers was significantly higher than for the RH whiskers. Due to preferred orientation of the whiskers, thermal conductivity and diffusivity of the composite samples exhibited significant anisotropy.     

High aspect ratio gold nanopillars on microelectrodes for neural interfaces

Microelectrode arrays (MEA) have become an established tool in applied and fundamental research. Low impedance at the interface between tissue and conducting electrodes is of utmost importance for the electrical recording or stimulation of electrophysiological active cells such as cardiac myocytes and neurons. A common way to improve this interface is to increase the electrochemically active surface area of the electrode. In this paper the fabrication of microelectrodes covered with very high aspect ratio (AR > 100) gold nanopillars is presented and electrode biocompatibility is investigated using cell culture experiments. The nanopillar electrodes show decreased impedance over the entire scanned frequency range of 1 Hz–100 kHz and an impedance improvement of up to 89.5 at 1 kHz depending on nanopillar height. Neurons adhere well to the substrate and electrodes and signals with amplitudes up to ten times higher than with conventional gold electrodes were recorded in cell culture experiments.     

Studies of lipoproteins and fatty acids in maternal and cord blood of two racial groups in Trinidad

The high mortality rate from coronary heart disease (CHD) among Indians compared to Negroes in Trinidad led us to test plasma lipid profiles to see whether dietary or genetic factors might be involved. There were no interracial differences in the composition of plasma cholesterol ester fatty acids of the tested women and neonates. This finding suggests that dietary fat does not account for the interracial difference in CHD, nor does the cause appear to be due to genetic differences in lipid profiles, as there was no significant difference between values for plasma triglycerides, total cholesterol, high density lipoprotein (HDL) cholesterol, apo-I, apo-II, apo B or cholesterol ester fatty acids in the cord blood of each racial group. Blood samples were collected from 69 nonpregnant and 71 postpartum, fasted Negro and Indian women. Also taken were 71 umbilical cord blood samples. The mean triglyceride level was significantly lower in the Negro nonpregnant and postpartum women than in the Indians. HDL cholesterol and apo-I values were lower in the Indian women. There were no significant differences in the total cholesterol and apo B measurements. The triglyceride values for postpartum women were higher than those of the nonpregnant Negroes and Indians (75% and 47%, respectively), whereas the total cholesterol and HDL cholesterol, apo A-I and apo A-II ranged from 9% to 29% higher in the postpartum women. Apo B was about 40% higher postpartum in both ethnic groups. The high CHD rate of Indians in Trinidad cannot be explained by dietary factors, plasma total cholesterol or fatty acid composition. However, the lower level of HDL cholesterol and plasma A-I could play a role in the higher CHD rate in Indians.     

Photochemical degradation of glassy polyesters of low softening point

The photodegradation of polyesters prepared by the reaction of o-phthalic, adipic, and “dimer” acids with ethylene glycol has been studied. The polyesters softened at temperatures in the range of 25–50°C. Polymer films were irradiated in air by means of a medium pressure mercury lamp and the extent of formation of COOH groups determined by infrared spectroscopy. The films were also irradiated in vacuo and in air by means of a high-pressure mercury lamp, and the volatile products, consisting mainly of carbon monoxide and carbon dioxide, were determined by gas chromatography. The results are interpreted in terms of simultaneous Norrish type I and type II decompositions of the polyesters. The type I process accounts for the formation of carbon monoxide and carbon dioxide in the absence of air. The enhanced yield of carbon dioxide in irradiations performed in air is ascribed to the formation of hydroperoxide which undergoes further photolysis. The type II process accounts for the formation of COOH groups. The photodegradation of these glassy polyesters parallels that of crystalline poly(ethylene terephthalate) and is relatively unaffected by changes in composition of the aromatic polyester.     

Length preferences and periodicity in {beta}-strands. Antiparallel edge {beta}-sheets are more likely to finish in non-hydrogen bonded rings

We analysed the length distributions of different types of ß-strandin a high resolution, non-homologous set of 500 protein structures,finding differences in their mean lengths. Antiparallel edgestrands in strand–turn–strand motifs show a preferencefor an even number of residues. This propensity is enhancedif the length is corrected for ß-bulges, which insertan extra residue into the strand. Residues in antiparallel edgeß-strands alternate between being in hydrogen bondedand non-hydrogen bonded rings. Antiparallel edges with an evennumber of residues are more likely to have their final ßresidue in a non-hydrogen bonded ring. This suggests that non-hydrogenbonded rings are intrinsically more stable than hydrogen bondedrings, perhaps because its side chain packing is closer. Therefore,we suggest that a simple way to increase ß-hairpinstability, or the stability of an antiparallel edge strand,is to have a non-hydrogen bonded ring at the end of the strand. Received June 19, 2003; revised October 25, 2003; accepted November 7, 2003     

Orientation effects during the flow of short-fibre reinforced thermoplastics

A study has been carried out to investigate molecular orientation in injection moulded bars of short glass fibre reinforced polypropylene and polyethylene. For the range of fibre concentrations encountered commercially, the fibres do not appear to have any direct effect on the matrix orientation. As the fibre concentration increases, however, the matrix orientation becomes dominated by the orientation of the fibres. These effects are interpreted in terms of current ideas of the rheology of polymer melts during injection moulding and the crystallization of polymers at fibre surfaces.     

Toughening epoxy resins with polyepichlorohydrin

Polyepichlorohydrin (PECH) rubbers were found to toughen epoxy resins based on the diglycidyl ether of bisphenol A (DGEBA) and cured with piperidine. The degree of toughening depends on the molecular weight of the PECH and on the curing temperature. Best toughening was achieved with PECH of the highest nominal molecular weight of 3400 (Hydrin 10 × 2). Hydrin 10 × 1 (nominal molecular weight 1700) did not toughen the epoxy resin unless bisphenol A was also added, whereas Hydrin 10 × 2 toughened it in the absence of bisphenol A. Curing resins containing bisphenol A and Hydrin 10 × 1 at 160°C resulted in a slightly more brittle resin than when cured at 120°C. The effect of PECH rubbers on the T_g, modulus, and hot/wet properties is similar to that of carboxy-terminated butadiene-acrylonitrile rubbers (CTBN). Dynamic mechanical thermal analysis (DMTA) and scanning electron micrographs (SEM) of fractured surfaces show that the PECH separates as a discrete phase during curing. © 1993 John Wiley & Sons, Inc.     

Dense subgraph maintenance under streaming edge weight updates for real-time story identification

Recent years have witnessed an unprecedented proliferation of social media. People around the globe author, everyday, millions of blog posts, social network status updates, etc. This rich stream of information can be used to identify, on an ongoing basis, emerging stories, and events that capture popular attention. Stories can be identified via groups of tightly coupled real-world entities, namely the people, locations, products, etc, that are involved in the story. The sheer scale and rapid evolution of the data involved necessitate highly efficient techniques for identifying important stories at every point of time. The main challenge in real-time story identification is the maintenance of dense subgraphs (corresponding to groups of tightly coupled entities) under streaming edge weight updates (resulting from a stream of user-generated content). This is the first work to study the efficient maintenance of dense subgraphs under such streaming edge weight updates. For a wide range of definitions of density, we derive theoretical results regarding the magnitude of change that a single edge weight update can cause. Based on these, we propose a novel algorithm, DynDens, which outperforms adaptations of existing techniques to this setting and yields meaningful, intuitive results. Our approach is validated by a thorough experimental evaluation on large-scale real and synthetic datasets.     

The influence of cure conditions on the morphology and phase distribution in a rubber-modified epoxy resin using scanning electron microscopy and atomic force microscopy

In this paper, we consider the effect of cure conditions on the morphology and distribution of the rubber in a phase separated rubber-modified epoxy resin, which in effect is a two phase composite. Novel aspects of this study were measuring the elastic modulus of the dispersed rubber phase particles by atomic force microscopy (AFM) and verifying the presence of nano-dispersed rubber.The purpose of introducing dispersed rubber particles into the primary phase in these systems is to enhance their toughness. It is known that both the rubber particle size and volume fraction affect the degree to which the epoxy is toughened. It is not known, however, how the specific mechanical properties of the rubber phase itself affect the toughness.The objectives of this study were to: (1) use scanning electron microscopy (SEM) and atomic force microscopy (AFM) to determine the morphology and phase distribution of the rubber particles and (2) to measure the mechanical properties of the rubber particles using AFM. Ultimately, we would like to develop a clear understanding of how the changes in morphology and mechanical properties measured at the micro and nano-scales affect both the elastic modulus and fracture toughness of rubber-modified epoxy polymers.The epoxy system consisted of a diglycidyl ether of bisphenol-A, Epon 828, cured with piperidine and incorporating a liquid carboxyl-terminated acrlonitrile-butadiene rubber (CTBN). The carboxyl groups of the rubber are capable of reacting with the epoxy. The cure conditions considered were based on a statistically designed full factorial curing matrix, with the variables selected being cure temperature, initiator (piperidine) concentration, and rubber acrylonitrile concentration.Each of these primary variables was found to affect the phase distribution that resulted during cure. A statistical analysis of the effect of these variables on the phase morphology showed that the acrylonitrile content (%) of the rubber affected both the rubber particle size and volume fraction. The cure temperature strongly influenced the rubber particle volume fraction and modulus. Volume fractions of the rubber phase of up to 24% were obtained even though the amount of rubber added was only 12.5%. The rubber particle modulus varied from 6.20 to 7.16 MPa. Both the volume fraction and modulus of the rubber particles were found to influence the macroscopic mechanical properties of the composite. While larger volume fractions favor improved toughness, we note that that the toughness is greatest when the particle modulus values do not exceed ∼6.2 MPa. Thus, increased volume fraction by itself may not always result in increased toughness. The particles also must be sufficiently ‘soft’ in order to improve toughness. In the system of interest here, the processing conditions are a key factor in achieving the most appropriate material properties. By inference, this is likely to be the case as well in other rubber-modified thermosets.