膜级钛系聚酯与锑系聚酯的成膜性能比较

利用流延膜挤出机、拉膜机分别对锑(Sb)系聚酯和钛(Ti)系聚酯进行挤出、拉伸成膜,考察了两种聚酯的成膜性能,对两种聚酯在加工过程中的热稳定性以及薄膜的热性能、力学性能、光学性能、取向结构进行了表征。结果表明:在挤出、拉伸过程中,Ti系聚酯的黏度降高于Sb系聚酯,Ti系聚酯切片的结晶度明显小于Sb系聚酯,但Ti系聚酯薄膜的结晶度与Sb系聚酯薄膜相当;在相同的成膜工艺下,Ti系聚酯薄膜的弹性模量、光学性能与Sb系聚酯薄膜相当,拉伸强度高于Sb系聚酯薄膜,断裂伸长率低于Sb系聚酯薄膜,双折射率大于Sb系聚酯薄膜。     

基于材料力学性能的最低设计金属温度曲线分析

铁素体钢在低温条件下存在明显的韧脆转变现象。为防止脆断事故的发生,需要确定铁素体钢制压力容器的最低使用温度。针对ASME中的A^D四条冲击豁免曲线,对应地选取了4种材料,基于材料实际的屈服强度和参考温度,按照ASME中豁免曲线的计算方法,计算得到4种材料的最低设计金属温度曲线,并与对应的A^D曲线对比,定量地分析ASME中豁免曲线的保守性。结果表明,ASME中的豁免曲线相对于材料自身的最低设计金属温度曲线保守性较大;韧性相近的材料被划分到不同的豁免曲线,使得韧性富裕量差异较大,对于某些材料,其断裂韧性被低估。     

Preparation and flocculation properties of biodegradable konjac glucomannan-grafted poly(trimethyl allyl ammonium chloride)

Polymer Bulletin - Preparation of konjac glucomannan-grafted poly(trimethyl allyl ammonium chloride) (KGM-g-PTMAAC) was carried out using KGM as polysaccharide matrix and TMAAC as cationic...     

核电厂人因可靠性分析中的相关性分析方法研究

人因可靠性分析（HRA）是核电厂风险分析中的重要组成部分，其中人误事件的相关性分析是HRA中必不可少的内容，忽略人误事件间的相关性，将导致低估核电厂的风险水平。本文提出了一种基于D（邓）数和层次分析法-决策试行与评价实验室（AHP-DEMATEL）方法的相关性分析模型。首先，确定两事件间相关性的影响因素及其结构关系，并针对每个影响因素建立相关性等级的隶属度函数及其锚点；其次，利用AHP-DEMATEL方法来确定各影响因素的综合权重；最后，根据实际情况评估各因素的相关性等级并构建D数，并根据D数和综合权重计算出两人因事件的相关性程度及其可信度，通过算例验证了该模型及其方法的有效性。      

单片机应用系统综合实验装置的设计

单片机原理与应用作为电子技术类学科中的必修课程具有很强实践性,要求学生掌握实际应用能力,为此研制了基于单片机系统通信为基础的实验板,依据单片机应用系统特点,可完成SPI、I^2C、UART串行通信以及并行总线方式通信。实验板有利于学生更好地了解和掌握单片机应用系统设计的方法,有利于学生进行自主设计和内容拓展。做到培养学生的学习能力、提高学生的学习兴趣、发挥学生的创造性。     

Mesoporous g-C3N4 decorated by Ni2P nanoparticles and CdS nanorods together for enhancing photocatalytic hydrogen evolution

Ni₂P nanoparticles and CdS nanorods were grew together on a mesoporous g-C₃N₄ through a facile in-situ solvothermal approach. Under visible light (λ > 400 nm), the as-prepared ternary PCN–CdS-5% Ni₂P composite displays a high H₂ evolution rate with 2905.86 μmol g^?1 h^?1, which is about 14, 18 and 279 times that of PCN–CdS, PCN–Ni₂P and PCN, respectively. The enhanced photocatalytic activity is mainly attributed to the improved separation efficiency of the photocarriers by the type II PCN–CdS heterojunction and the effective extraction of photogenerated electrons by Ni₂P. Meanwhile, Ni₂P acts as co-catalyst to provide the photocatalytic active site for hydrogen reduction. In addition, PCN–CdS-5% Ni₂P composite exerts good stability in 12-h cycles.     

Blocked crystallization in capped ultrathin polymer films studied by molecular simulations

The crystallization of capped ultrathin polymer films is closely dependent on film thickness and interfacial interaction. Using dynamic Monte Carlo simulations, the crystallization behaviors of polymer films confined between two substrates were investigated. The crystallization rate of confined polymers is reduced with high interfacial interactions. Above a critical strength of interfacial interaction, polymer crystallization in the thin film is inhibited within the simulation time scales. An increase in film thickness leads to a rise in critical interfacial interaction. In thicker films, the chains have more space to change conformation to form crystal stems. In addition, there are fewer absorbed segments in confined chains for the thicker films, and thus the chains have stronger ability to adjust their conformation. Therefore an increase in film thickness can cause a reduction in the entropic barrier required for the formation of crystals and thus an increase in the critical interfacial interaction. © 2018 Society of Chemical Industry