Performance evaluation of a submerged membrane bioreactor for the treatment of brackish oil and natural gas field produced water

Produced water, which is co-produced during oil and gas manufacturing, represents one of the largest sources of oily wastewaters. Therefore, treatment of this produced water may improve the economic viability and lead to a new source of water for beneficial use. In this study a submerged hollow fiber membrane bioreactor (MBR) has been studied experimentally for the treatment of brackish oil and natural gas field produced water. This type of wastewater is also characterized with relatively moderate to high amount of salt, oil and total petroleum hydrocarbons (TPH). However, the bacteria which are growing in conventional activated sludge and MBR cannot survive at these strict conditions, therefore acclimation of the bacteria is of vital importance. The performance of the biological system, membrane permeability, the rate and extent of TPH biodegradability have been investigated under different sludge age and F/M ratios. The results obtained by gas chromatography analyses showed that the MBR system could be very effective in the removal of TPH from produced water and a significant improvement in the effluent quality was achieved.     

An experimental investigation on the effects of exponential window and impact force level on harmonic reduction in impact-synchronous modal analysis

A novel method called Impact-synchronous modal analysis (ISMA) was proposed previously which allows modal testing to be performed during operation. This technique focuses on signal processing of the upstream data to provide cleaner Frequency response function (FRF) estimation prior to modal extraction. Two important parameters, i.e., windowing function and impact force level were identified and their effect on the effectiveness of this technique were experimentally investigated. When performing modal testing during running condition, the cyclic loads signals are dominant in the measured response for the entire time history. Exponential window is effectively in minimizing leakage and attenuating signals of non-synchronous running speed, its harmonics and noises to zero at the end of each time record window block. Besides, with the information of the calculated cyclic force, suitable amount of impact force to be applied on the system could be decided prior to performing ISMA. Maximum allowable impact force could be determined from nonlinearity test using coherence function. By applying higher impact forces than the cyclic loads along with an ideal decay rate in ISMA, harmonic reduction is significantly achieved in FRF estimation. Subsequently, the dynamic characteristics of the system are successfully extracted from a cleaner FRF and the results obtained are comparable with Experimental modal analysis (EMA).     

Numerical investigations on dynamic performance of stiffened box steel bridge piers

The aim of this paper is to carry out extensive numerical investigations about the effect of various structural parameters on the dynamic performance of stiffened box steel bridge pier under a strong earthquake ground motion. The considered structural parameters are the local slenderness ratios of stiffener and stiffened wall as well as the global slenderness ratio of the pier. In the present study, all investigated piers are made of high tensile steel with high yield ratio. The non-linear time history analyses are carried out using in-house Finite Element Program DYNAPSS, recently developed by the first author. This program is verified by comparing its results with the results obtained by the general FE program. In this program, the geometrical nonlinearity is considered on the bases of Total Lagrangian formulation, while the non-linearity of structural steel material is considered through implementation of modified multisurface cyclic plasticity model by which real characteristics of high tensile steel material such as, Plateau, Massing type of Bauschinger??s effect, disappearing of Plateau and cyclic strain hardening, are accurately modeled. The results are closely examined in respect with the damage index criterion. From this study, it is found that the increase in slenderness ratios of stiffener does not only increase the damage index, but also may lead to the full collapse. Furthermore, the damage index increases with the increase of local slenderness ratio of stiffened wall and the global slenderness ratio. Also, it is found that when the loacal buckling is not the dominant eigen mode and the pier behave as a single degree of freedom, the natural period has destructive effects when it is close to predominant period of the earthquake. Finally, contour plots of damage index values are presented. These contour plots may be greatly useful for the design of stiffened box steel bridge piers, where, critical values of structural parameters corresponding to certain value of damage index could be determined.     

Hypoglycemic effects of cocoa (Theobroma cacao L.) autolysates

Fat, alkaloid and polyphenol contents of two clones of cocoa (UIT1 and PBC 140) were removed and the remaining powder was autolyzed at pH 3.5 and 5.2. Based on the results, autolysates of UIT produced at pH 3.5 exhibited the highest ability to inhibit α-amylase activity. However, no α-glucosidase inhibition activity was observed under the conditions specified. Autolysates produced under pH 3.5 caused the highest amount of insulin secretion. In streptozotocin-diabetic rats, all cocoa autolysates significantly decreased blood glucose at 4 h. To assure that the results from the assays were not due to the polyphenols of cocoa autolysates qualitative and quantitative tests were applied. According to their results cocoa autolysates were found to be free from polyphenols. Analysis of amino acid composition revealed that cocoa autolysates were abundant in hydrophobic amino acids. It can be suggested that besides other compounds of cocoa, its peptides and amino acids could contribute to its health benefits.     

Polyvinylidene fluoride and polyetherimide hollow fiber membranes for CO2 stripping in membrane contactor

Porous polyvinylidene fluoride (PVDF) and polyetherimide (PEI) hollow fiber membranes incorporating polyethylene glycol (PEG) were prepared via spinning process for CO₂ membrane stripping. CO₂ loaded diethanolamine solution was used as liquid absorbent while N₂ was used as a strip gas. The characterization study of the fibers was carried out in terms of permeation test, contact angle measurement and liquid entry pressure (wetting pressure). Performance study via membrane contactor stripping was carried out at specific operating condition. The experimental results showed that PVDF membrane have high gas permeation, effective surface porosity and contact angle despite having lower liquid entry pressure in comparison with PEI membrane. PVDF-PEG membrane showed the highest stripping flux of 4.0 × 10⁻² mol m⁻² s⁻¹ at 0.7 ms⁻¹ compared to that of PEI membrane. Although the stripping flux for PEI-PEG membranes was slightly lower than PVDF membrane (e.g. 3.5 × 10⁻² mol m⁻² s⁻¹ at liquid velocity of 0.85 ms⁻¹), the membrane wetting pressure of PEI membrane is higher than hydrophobic PVDF membrane. Long term performance of both membranes showed severe flux reduction but started to level-off after 30 h of operation.     

Phase Transformations of α-Alumina Made from Waste Aluminum via a Precipitation Technique

We report on a recycling project in which α-Al₂O₃ was produced from aluminum cans because no such work has been reported in literature. Heated aluminum cans were mixed with 8.0 M of H₂SO₄ solution to form an Al₂(SO₄)₃ solution. The Al₂(SO₄)₃ salt was contained in a white semi-liquid solution with excess H₂SO₄; some unreacted aluminum pieces were also present. The solution was filtered and mixed with ethanol in a ratio of 2:3, to form a white solid of Al₂(SO₄)₃·18H₂O. The Al₂(SO₄)₃·18H₂O was calcined in an electrical furnace for 3 h at temperatures of 400–1400 °C. The heating and cooling rates were 10 °C/min. XRD was used to investigate the phase changes at different temperatures and XRF was used to determine the elemental composition in the alumina produced. A series of different alumina compositions, made by repeated dehydration and desulfonation of the Al₂(SO₄)₃·18H₂O, is reported. All transitional alumina phases produced at low temperatures were converted to α-Al₂O₃ at high temperatures. The X-ray diffraction results indicated that the α-Al₂O₃ phase was realized when the calcination temperature was at 1200 °C or higher.     

Application of MIKE SHE modelling system to set up a detailed water balance computation

Estimation of total water balance is a substantial issue for watershed modelling in order to simulate the major components of the hydrological cycle to determine the stress of different anthropogenic activities on the available water resources within a catchment. In this context, the fully distributed physically based MIKE SHE modelling system was used to simulate the individual hydrological components of the total water balance for the Paya Indah Wetlands (PIW) watershed in the west of Peninsular Malaysia. Results reveal that the overall water balance is predominantly controlled by climate variables. Application of the model to the PIW watershed provides detailed estimation of the total water balance for a first‐order catchment in which actual evapotranspiration (ET) represents approximately 65 and 58%, while overland flow (OL) to the PIW lake system represents 12.38 and 12.3% of the total rainfall during the calibration and validation periods, respectively. The difference of the inflow and outflow was taken as storage in depth. Overall, the model gives a reasonable output of total error of less than 1% of the total rainfall, which in turn indicates that the interaction among components is satisfactorily sustained.