Hybrid photocatalytic membranes embedding decatungstate for heterogeneous photooxygenation

The incorporation of decatungstate in polymeric membranes provides new heterogeneous photocatalysts for the oxidation of organic substrates under oxygen atmosphere at 25 °C. Photocatalytic membranes have been prepared yielding polymeric films with a high thermal, chemical and mechanical stability (PVDF, PDMS, Hyflon). Surface spectroscopy techniques including transmittance and reflectance UV-Vis and FT-IR have been used to assess the photocatalyst integrity within the polymeric support. Catalyst screening has been performed under both homogeneous and heterogeneous photooxygenation conditions. The photocatalyst activity has been evaluated in terms of the substrate conversion, turnover numbers, and recycling experiments. A membrane induced selectivity behavior has been evidenced by comparison with homogeneous oxidations.     

Introductory Paper

In today’s competitive market designing of digital systems (hardware as well as software) faces tremendous challenges. In fact, notwithstanding an ever decreasing project budget, time to market and product lifetime, designers are faced with an ever increasing system complexity and customer expected quality. The above situation calls for better and better formal verification techniques at all steps of the design flow. This special issue is devoted to publishing revised versions of contributions first presented at the 12th Advanced Research Working Conference on Correct Hardware Design and Verification Methods (CHARME) held 21–24 October 2003 in L’Aquila, Italy. Authors of well regarded papers from CHARME’03 were invited to submit to this special issue. All papers included here have been suitably extended and have undergone an independent round of reviewing.     

Saw and digital technologies in mutlicarrier demodulators

One key technology, for the implementation of future on-board processing payloads, is the multicarrier demodulator (MCD). The MCD is instrumental in allowing FDMA/TDM access schemes which optimize the use of on-board and ground resources in VSAT networks. This paper deals with the analogue and digital implementations of MCD, trying to assess the fields of application of each of the two technologies.     

A VLSI structure forX(modm) operation

High-computing speed and modularity have made RNS-based arithmetic processors attractive for a long time, especially in signal processing, where additions and multiplications are very frequent. The VLSI technology renewed this interest because RNS-based circuits are becoming more feasible; however, intermodular operations degradate their performance and a great effort results on this topic. In this paper, we deal with the problem of performing the basic operationX(modm), that is the remainder of the integer divisionX/m, for large values of the integerX, following an approximating and correcting approach, which guarantees the correctness of the result. We also define a structure to computeX(modm) by means of few fast VLSI binary multipliers, which is exemplified for 32-bit long numbers, obtaining a total response time lower than 200 nsec. Furthermore, such a structure is evaluated in terms of VLSI complexity and area and time figuresA=?(n ² T _m ² ) andT=?(T _M ) for the parameterT _M in \([\log n,\sqrt n ]\) are derived. A simple positional-to-residue converter is finally presented, based on this structure; it improves some complexity results previously obtained by authors.     

Rheological evaluation of the influence of polymer concentration and molar mass distribution on the formation and performance of asymmetric gas separation membranes prepared by dry phase inversion

Asymmetric gas separation membranes were prepared by the dry-casting technique from PEEKWC, a modified amorphous glassy poly(ether ether ketone). The phase inversion process and membrane performance were correlated to the properties of the polymer and the casting solution (molar mass, polymer concentration, solution rheology and thermodynamics). It was found that a broad molar mass distribution of the polymer in the casting solution is most favourable for the formation of a highly selective membrane with a dense skin and a porous sub-layer. Thus, membranes with an effective skin thickness of less than 1 μm were obtained, exhibiting a maximum O₂/N₂ selectivity of 7.2 and a CO₂/CH₄ selectivity of 39, both significantly higher than in a corresponding thick dense PEEKWC membrane and also comparable to or higher than that of the most commonly used polymers for gas separation membranes. The CO₂ and O₂ permeance were up to 9.5×10⁻³ and 1.8×10⁻³ m³/(m² h bar) (3.5 and 0.67 GPU), respectively.     

Blends of polyamide 6 with bisphenol-A polycarbonate. I. Thermal properties and compatibility aspects

Blends of polyamide 6 (PA6) and polycarbonate (PC) have been investigated, over a full range of composition, to check interactions between them. SEM observations show that the mixtures are characterized by domains of clearly segregated homophases and voids between the two polymers. DSC and DMTA data indicate the presence of two T_g' s, corresponding to two separate phases, with the T_g of the PC phase decreasing on increasing the PA6 amount. Moreover, the crystallization kinetics of PA6 is slightly showed down by the PC. Chemical reactions between the two polymers are supposed to give rise to low molar mass compounds, as shown by GPC; these species plasticize the PC and partially dissolve into the molten polyamide, causing decrease of PC T_g and reduction of overall crystallization rate of PA6. Apparent influence of PC on melting temperature and enthalpy of PA6 is also discussed.     

Controlled pore size, thickness and surface free energy of super-hydrophobic PVDF® and Hyflon®AD membranes

Super-hydrophobic membranes were manufactured by using two per-fluorinated polymers such as PVDF and Hyflon AD. The combination of controlled structure and supra-molecular chemistry made these membranes ideal interfaces to be used in membrane contactors.     

NH3-NO/NO2 SCR for diesel exhausts after treatment: mechanism and modelling of a catalytic converter

We review herein the key mechanistic and kinetic features of the reactions involved in the NH₃-NO/NO₂ SCR system investigated by dynamic reactive experiments over a V-based commercial powdered catalyst, eventually leading to the proposal of an original redox scheme which accounts for stoichiometry, selectivity and intrinsic kinetics of the global SCR process.     

Practical and theoretical molecular weights in polyaddition reactions of ethylene and propylene oxide

The addition reactions of ethylene oxide and/or propylene oxide catalyzed by KOH and initiated with compounds containing free hydroxyls are followed by secondary reactions which vary the expected molecular weight. By using ethylene oxide, diols are formed and by using propylene oxide, both diols and unsaturated monofunctional compounds are formed. These products are usually characterized by their hydroxyl number. The average molecular weight is found by taking into consideration the starter functionality only. There are often some behavioral differences among similar products owing to the different quantity and chain length of the secondary products contained therein. The secondary products are analyzed and the quantity of the secondary products were determined from the hydroxyl number values and from the unsaturation of reagents and products. In the case of monofunctional adducts using the calculation method, the results have been experimentally confirmed.