Effect of surface structure on biomechanical properties and osseointegration

The purpose of this study is to improve the bone-bonding ability between titanium implants and living bone through the control of geometric design and chemical compositions of an implant surface. We compared the tissue healing response and resulting implant stability for three surface designs by characterizing the histological and mechanical properties of the healing tissue around smooth-surfaced Ti–6Al–4V (SS), CP-Ti plasma-spray-coated (PSC), alkali- and heat-treated (AHT) implants. The implants were transversely inserted into a dog thighbone and evaluated at 4, 8, and 12 weeks. Histological examination indicated that initial matrix mineralization leading to osseointegration occurred more rapidly with the AHT implant. During the 4, 8, and 12 week healing periods, new bone on the surface of AHT implant showed denser growth than that on the SS and PSC implants. The more extensive tissue integration and more rapid matrix mineralization with the AHT implant were reflected in the mechanical test data, which demonstrated superior attachment strength and interfacial stiffness for the AHT implant after healing for 4, 8 and 12 weeks of healing because of the mechanical interlocking in the micrometer sized rough surface and the large bonding area between bone and implant caused by the nanosized porous surface structure. Histological and mechanical data demonstrate that with the appropriate surface design selection, bone bone-bonding ability can be improved and can induce acceleration of the healing response, thereby improving the potential for implant osseointegration.     

Synthesis and structural properties of lithium titanium oxide powder as-synthesized by two step calcination process

A two-step calcination synthesis, considering the potential for mass production, of lithium titanium oxide powder was carried out to fabricate a single Li₄Ti₅O₁₂ phase, which is useful for anode electrode material of Li-based rechargeable battery as well as an electrode for supercapacitor. The final composition is controlled by adding more TiO₂ powder into powder gained at one calcination process during the two calcination process. We investigated the influence of excess TiO₂ on the structural characteristics of lithium titanium oxide synthesized by the two-step calcination method. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) measurements showed that the as-synthesized powder had a spinel crystal structure as well as A composition of 4: 5: 12. In addition, a high resolution transmission electron microscopy (HRTEM) analysis revealed that the fabricated powder exhibited a single crystalline phase formation. These results indicated that the powder synthesized in the one-step calcination process showed coexistence crystalline phases, which are the Li₄Ti₅O₁₂ and Li_2.39Ti_3.4O₈ phase. However, in the two-step calcination process, the powder synthesized showed the single crystalline Li₄Ti₅O₁₂ phase. A very uniform grain size of the as-synthesized powder was shown in a field emission scanning electron microscopy (FESEM). These results suggested that the two-step calcination process can be used for synthesis of single crystalline Li₄Ti₅O₁₂ powder with uniform grain shape and provide motivation to pursue mass production of lithium titanium based oxide powder for bulk type batteries.     

Distributed diagnosis for homogeneous systems

This article presents a distributed fault-diagnosis algorithm for identifying faulty and fault-free units (processors, PEs, cells) in homogeneous systems. It is based on local comparison among units in a system and dissemination of the test results. Each unit performs comparison with its neighbors by using its own comparator. Unlike other approaches, the algorithm does not assume that diagnostic circuits are fault free. The algorithm is simple enough to be realized with small circuit overhead. The results are especially useful in locating faulty units in processor arrays implemented on a single chip or wafer. Computer simulation has shown that even for low unit yields, extremely high performance (fault coverage) can be obtained by adjusting algorithm parameters.     

Analysis of steady state of free radical solution polymerization in a continuous stirred tank reactor

The steady state structure of non-isothermal free radical solution polymerization in a continuous stirred tank reactor is analyzed. With mean residence time as a bifurcation parameter, five regions of steady states are identified. The effect of reactor operating conditions on the structure and the stability of steady state is discussed.     

Influence of Si<Subscript>3</Subscript>N<Subscript>4</Subscript> passivation on surface trapping in SiC metal-semiconductor field-effect transistors

The SiC metal-semiconductor field-effect transistors (MESFETs) have been reported to have current instability and strong dispersion caused by trapping phenomena at the surface and in the substrate, which degrade direct-current (DC) and radio-frequency (RF) performance. This paper illustrates the change in electrical characteristics of SiC MESFETs after Si₃N₄ passivation. Because of a reduction of surface trapping effects, Si₃N₄ passivation can diminish current collapse under pulsed DC conditions, increasing the RF power performance. The reduction of surface trapping effects is verified by the change in the ratio of the drain current to the gate current under pinch-off conditions.     

Numerical prediction of three-dimensional fiber orientation in Hele-Shaw flows

A numerical technique is developed to determine the three-dimensional fiber orientation in complex flows. The fiber orientation state is specified in terms of orientation tensors, which are used in several constitutive models. This method is applied to quasi-steady state Hele-Shaw flows in order to predict the flow-induced fiber orientation during injection molding at zero volume fraction limit. At the inlet, a number of fibers are introduced at a specified rate into the flow and each fiber location is traced during the mold filling. Along these determined paths, the independent components of fourth order orientation tensors are solved, describing the orientation state. The numerical grid generation technique, which is suitable for complex mold shapes, is employed for the flow solution. Orientation ellipsoids are calculated from the second order tensors and are used to present the fiber orientation results. The numerical solutions are obtained for channel and converging flows. Planar, longitudinal, and transverse orientation results are generated from the orthogonal projections of the orientation ellipsoids.     

Performance analysis of virtual time ICMA/CD

The performance of a virtual time idle-signal casting multiple access with collision detection (ICMA/CD) protocol is analysed under the infinite population model. Compared to the existing nonpersistent and 1-persistent schemes, the virtual time protocol exhibits high throughput and lower packet failure probability in mobile radio networks.<>