Discussion influence of yield surface curvature on flow localization in dilatant plasticity

The results of finite element calculations for a hollow sphere micromodel are used to examine the underlying assumptions and the specific yield functions in the dilatant plasticity theories of Gurson (1977) and Mear and Hutchinson     

Effect of moderate to very low fat defined formula diets on serum lipids in healthy subjects

Serum total cholesterol, high density lipoprotein (HDL) cholesterol, and triglyceride levels were studied in healthy male and female subjects consuming for one-week periods a diet of conventional food (CF) providing 42% of energy as fat, principally butter fat, and then in random order nutritionally complete, defined formula diets of moderate (32%) to very low (1%) fat content. Compared to CF, the formula with 32% of energy as corn oil lowered serum cholesterol by 25% and the ratio of total to HDL-cholesterol by 13%. Low (9%) and very low (1–3%) fat formulas reduced HDL-cholesterol by as much as 40%, raised the total: HDL-cholesterol ratio by about 20% and raised serum triglyceride levels by as much as 100%. When low and very low fat formulas were ingested for three weeks, these effects persisted although maximal responses occurred during the first week. These results demonstrated that a moderate fat formula diet with a high P/S ratio had a more favorable effect on serum lipid levels than various low fat formulas. Low fat conventional food diets should be studied in long-term controlled metabolic experiments before such diets are recommended to the general population for coronary heart disease or cancer prevention.     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Primary hydration of poly(acrylic acid) sodium salts

Summary The equilibrium water contents of linear poly(acrylic acid) sodium salts with different degrees of neutralisation were found to be dependent on temperature and relative humidity. An octahedral model for the primary hydration of poly(acrylic acid) sodium salts (HIRAOKA and YOKOYAMA 1980) was critically evaluated in the light of these findings and an anomaly in the water uptake versus neutralisation curve at approximately 33% neutralisation was explained by the counterion condensation theory. (MANNING 1979).     

Magnetic resonance imaging (MRI) site planning and economics

Site planning and economic forecasting for MRI require careful, individualized analysis of several possible sites. Particular attention should be accorded to the magnetic environment. Realistic estimates of financial feasibility will depend heavily on decisions of regulators and third-party payers.     

K-winner networks.

A special class of mutually inhibitory networks is analyzed, and parameters for reliable K-winner performance are presented. The network dynamics are modeled using interactive activation, and results are compared with the sigmoid model. For equal external inputs, network parameters that select the units with the larger initial activations (the network converges to the nearest stable state) are derived. Conversely, for equal initial activations, networks that select the units with larger external inputs (the network converges to the lowest energy stable state) are derived. When initial activations are mixed with external inputs, anomalous behavior results. These discrepancies are analyzed with several examples. Restrictions on initial states are derived which ensure accurate K-winner performance when unequal external inputs are used.     

Making99Mo in reactors

Conclusions This comparison of two ways of making⁹⁹Mo shows that there is good scope for making it in any area. If there is a thermal reactor having a high flux, one can make⁹⁹Mo from⁹⁸Mo, and in that case, even irradiation in a high flux makes it favorable to use highly enriched⁹⁸Mo and unblocked targets, which raises the specific activity and thus increases the working life in the^99mTc generator.If there is a thermal reactor with low flux or if there is a fast reactor it is best to make⁹⁹Mo from uranium fission products. The target can be highly enriched²³⁵U, which if necessary can be reused, or low-enriched uranium.There are no essential constraints on making⁹⁹Mo, and the production is mainly based on technological tasks.Translated from Atomnaya Énergiya, Vol. 67, No. 2, pp. 104–108, August, 1989.