Electrical resistivity and Seebeck coefficient of La1−x M x MnO3 (M = Ca,Sr) single crystals

The temperature dependence of the electrical resistivity and Seebeck coefficient was measured on single crystals of La_1–x Ca _x MnO₃(0 <x 0.3) and La_1–x Sr _x MnO 3 (0 <x 0.4) grown by the arc-image floating zone method. The electrical conduction for La_1–x crystals withx 0.2 was of the activation type aboveT _c and of the degenerate type belowT _c, while that for the crystal withx = 0.1 was of the activation type over the whole measured temperature range between –170 and 400°C. The conduction behaviour of La_{1– x} Sr _x MnO₃ was essentially the same as that of La_1–x Ca _x MnO₃ except that the conduction of the crystals withx = 0.3 and 0.4 was of the degenerate type aboveT _c. A distinct difference in Seebeck data was observed between the calcium and the strontium compounds.     

An XPS study of passive films on Nickel and alloy 600 in acids

Compositions of surface films formed on nickel and Alloy 600 in I M HCI, 0.5 M H₂SO₄ and I/3 M H₃PO₁ solutions were investigated as a function of polarization potential. The main constituent of surface films formed on Ni in 0.5 M H₂SO₄ or 1/3 M H₃PO₄ solution was hydrated nickel oxyhydroxide, in which the ratio of O₂ to OH⁻ increased when passivation occurred. The surface films formed on Ni and Alloy 600 at lower potentials in 0.5 M H₂SO₄ solution contain S² ions other than SOP_4²⁻ ions, whereas S²⁻ ions were not incorporated in the passive film. Passivation of Alloy 600 took place by the formation of hydrated chromium oxyhydroxide. Pitting led to no substantial change in the average composition of the film.     

Importance of initial surface film in the degradation of stainless steels by atmospheric exposure

The surface compositions of stainless steels types 304, 316, 430, and 444 combined with four types of surface finishes, 2B finish, hairline polishing, mirror polishing, and bright annealing, were measured by ICP-AES, EPMA, and XPS before exposure. The surface finish that most enriched the chromic species in the surface film was mirror polishing, followed by bright annealing, 2B finish, and hairline polishing. The order of corrosion-resistance was type 444, type 316, type 304, and type 430. The surface compositions were correlated with the rating number and pitting depth after exposure to atmospheric environments. The rating number had a high positive correlation with the concentration of Cr in the surface film, and had a slight correlation with the near-surface composition measured by EPMA at 12 kV, but did not show any correlation with bulk composition within the composition range covered in the present work. This same trend was observed for pitting depth. It was concluded that the cationic concentration of Cr in the surface film before atmospheric exposure is the prime factor in controlling the resistance of stainless steels to atmospheric corrosion.     

Studies on the nuclear magnetic resonance spectra of olefinic protons of conjugated fatty acid methyl esters

The NMR spectra of olefinic protons in the four representative conjugated fatty acid methyl esters, methylcis-9,trans-11-octadecadienoate, methyltrans-9,trans-11-octadecadienoate, methyl α eleostearate, and methyl β eleostearate, were studied. The chemical shift of each olefinic proton in these compounds was determined by considering their intramolecular environment. Coupling constants were also obtained as the results of spectral analysis.     

Poly(L‐lactide). X. Enhanced surface hydrophilicity and chain‐scission mechanisms of poly(L‐lactide) film in enzymatic,alkaline, and phosphate‐buffered solutions

Attempts were carried out to enhance the surface hydrophilicity of poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA) film, utilizing enzymatic, alkaline, and autocatalytic hydrolyses in a proteinase K/Tris–HCL buffered solution system (37°C), in a 0.01N NaOH solution (37°C), and in a phosphate‐buffered solution (100°C), respectively. Moreover, its chain‐scission mechanisms in these different media were studied. The advancing contact‐angle (θ_a) value of the amorphous‐made PLLA film decreased monotonically with the hydrolysis time from 100° to 75° and 80° without a significant molecular weight decrease, when enzymatic and alkaline hydrolyses were continued for 60 min and 8 h, respectively. In contrast, a negligible change in the θ_a value was observed for the PLLA films even after the autocatalytic hydrolysis was continured for 16 h, when their bulk M_n decreased from 1.2 × 10⁵ to 2.2 × 10⁴ g mol^?1 or the number of hydrophilic terminal groups per unit weight increased from 1.7 × 10^?5 to 9.1 × 10^?5 mol g^?1. These findings, together with the result of gravimetry, revealed that the enzymatic and alkaline hydrolyses are powerful enough to enhance the practical surface hydrophilicity of the PLLA films because of their surface‐erosion mechanisms and that its practical surface hydrophilicity is controllable by varying the hydrolysis time. Moreover, autocatalytic hydrolysis is inappropriate to enhance the surface hydrophilicity, because of its bulk‐erosion mechanism. Alkaline hydrolysis is the best to enhance the hydrophilicity of the PLLA films without hydrolysis of the film cores, while the enzymatic hydrolysis is appropriate and inappropriate to enhance the surface hydrophilicity of bulky and thin PLLA materials, respectively, because a significant weight loss occurs before saturation of θ_a value. The changes in the weight loss and θ_a values during hydrolysis showed that exo chain scission as well as endo chain scission occurs in the presence of proteinase K, while in the alkaline and phosphate‐buffered solutions, hydrolysis proceeds via endo chain scission. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1628–1633, 2003     

Fate of the chlorine and fluorine in a sub-bituminous coal during pyrolysis and gasification

The fate of the chlorine and fluorine present in a sub-bituminous coal from Indonesia during pyrolysis and gasification has been studied with fixed and entrained bed reactors. The rate profile for HCl evolved in the temperature programmed pyrolysis exhibits the main and shoulder peaks at 480 and 600 °C, respectively. Model experiments and subsequent Cl 2p XPS measurements show that HCl reacts with metal impurities and carbon active sites at 500 °C to be retained as inorganic and organic chlorine forms, from which HCl evolves again at elevated temperatures. It is suggested that the HCl observed in the coal pyrolysis may originate from the above-mentioned chlorine functionalities formed by secondary reactions involving the nascent char. In the CO₂ gasification of the 900 °C char at 1000 °C and 2.5 MPa, any measurable amounts of HCl and HF could not be detected even at a high conversion of 75 wt% (daf), suggesting the accumulation of these halogens in the residual char. When the coal is injected into an O₂-blown, entrained bed gasifier at 1200-1400 °C under 2.6 MPa, the partial oxidation proceeds to a larger extent at a higher O₂/coal ratio, whereas the chlorine and fluorine are enriched in the remaining char, and the extent of the enrichment at the latter stage of gasification is larger with the fluorine. The XPS measurements of the chars reveal the presence of the broad F 1 s peak, which can cover a wide range of binding energies attributable to inorganic and organic fluorine. The halogen enrichment during gasification is discussed in terms of secondary reactions of HCl and HF with char.     

The surface film formed on amorphous Pd-Ti-P alloy by anodic polarization in 2 m NaCl solution

X-ray photoelectron spectroscopy was used to investigate the effect of the composition and thickness of surface film on the electrocatalytic properties for chlorine gas evolution on amorphous Pd-Ti-P alloy in NaCl solution. The amount of charge for gas evolution exhibited a wavy change with an increase in polarization potential. The gas evolution became active with an increase in palladium content of the surface film and slowed down with increases of titanium and phosphorus contents of the film. However, despite the fact that the formation of surface film consisting mainly of titanium as a cation in the potential region higher than 1.6 V (sce), the catalytic activity for gas evolution increased, suggesting the change in the gas evolution mechanism in the higher potential region.     

Anodic characteristics of amorphorous palladium-base alloys in sodium chloride solutions

The anodic characteristics of a variety of amorphous palladium-base alloys were examined with a view to their use for the production of sodium hypochlorite by electrolysis of dilute sodium chloride solutions at ambient temperature. The corrosion resistance of palladium-metalloid alloys was obtained by alloying with platinum group metals and/or valve metals. Among these alloys, rhodium-containing alloys showed high electrocatalytic activities for chlorine evolution. Surface activation treatment was, however, necessary to obtain sufficiently high activities for chlorine evolution at low overpotentials. Surface-activated amorphous alloys possessed considerably higher current efficiency for chlorine evolution in comparison with currently used anodes.     

An X-ray photoelectron spectroscopic study of electrocatalytic activity of platinum group metals for chlorine evolution

A correlation of the catalytic activity for anodic chlorine evolution of platinum group metals to the nature of the surface film formed during chlorine evolution in a sodium chloride solution was studied by X-ray photoelectron spectroscopy. The change in the surface film with increasing potential was found on platinum, including an increase in the cationic valence. This seemed responsible for the decrease in the activity for chlorine evolution on platinum in the high potential region. Increasing potential did not result in the appreciable increase in the cationic valence in the surface film on the other platinum group metals. Replacement of hydroxyl ions in the surface film by chloride ions became easier in the order of rhodium, iridium and palladium, and the activity for anodic chlorine evolution increased in this order due possibly to an increase in the amount of chloride ions in the film which seemed to be one of the reactants in the rate determining electrochemical desorption of adsorbed chlorine atom. Chlorine molecules adsorbed on the surface film were also found. It was assumed that the activity for anodic chlorine evolution might be low when the metal surface was covered by a large amount of molecular chlorine which was the reaction product.     

Fracture toughness of silica particulate‐filled epoxy composite

The relationship between the postcuring conditions and fracture toughness on three silica particulate‐filled epoxy composites was investigated. The glass transition temperature, T_g, and the fragility parameter, m, derived from the thermo‐viscoelasticity, were used to characterize the composites, which were postcured under various conditions. The glass transition temperature and fragility both depended on both of the curing conditions and the volume fraction of silica particles. The glass transition temperature increased with the postcuring time and temperature, while the fragility generally decreased as the volume fraction increased. There was no direct correlation between the glass transition temperature and fragility. The fracture toughness depended on both the glass transition temperature and fragility. The composites with a high glass transition temperature and low fragility had high fracture toughness. These results indicate that the glass transition temperature and fragility are useful parameters for estimating the fracture toughness of the silica particulate‐filled epoxy composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2261–2265, 2002