Performance and Commercial Application of the Promoter LCC-A for Maximization of Propylene Yield

1 Introduction Propylene as an important feedstock for organic chemicals is mainly originated from steam cracking and catalytic cracking processes. During the FCC process the propylene content varies with the FCC catalyst and process technology adopted, resulting in significant difference in propylene concentration in the cracked product——LPG. The conventional FCC pro- cess generally gives a propylene yield of around 4%, while the FCC process with maximization of propylene yield can in…     

JX-300X系统与智能设备数据通讯的实现

介绍了SUPCON JX-300X SXA与符合Profibus-DP的现场智能设备的通讯实施方法．     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

丙烯腈装置回收塔内聚合物生成原因的分析

针对丙烯腈生产过程中回收塔内聚合物堵塞降液管造成回收塔运行周期短的问题,通过对丙烯腈回收塔内各组分分布的模拟计算,直观显示了回收塔内各组分的浓度分布,发现了回收塔的聚合段与丙烯醛的富集段相吻合的现象,初步得出了回收塔内局部聚合的原因;通过对塔内聚合物的特性分析和评判,进一步证实了“回收塔内局部聚合严重是由于在聚合段丙烯醛聚集引起”这一现象;根据模拟计算结果和实际运行经验,提出了预防聚合物堵塞降液管的措施,并进行了部分生产验证,为丙烯腈生产企业延长装置运行周期提供了理论指导。     

TUD-DNS3脱硝助剂在催化裂化装置的工业应用

TUD-DNS3脱硝助剂在中韩（武汉）石油化工有限公司1号催化裂化装置上进行了工业应用。结果表明：针对两段再生工艺，当系统中助剂占总催化剂藏量的质量分数为2.6%时，烟气脱硫装置外排污水中的氨氮质量浓度由加剂前的100 mg/L下降至40 mg/L以内；助剂的加入降低了CO焚烧炉的炉膛温度，有利于烟气的合格排放，并对装置操作、产品分布及汽油、柴油产品质量无不良影响。     

微制造平台微振动的最优控制

采用混合隔振技术建立了微制造平台隔振系统。该系统以空气弹簧和橡胶层作为被动隔振元件、超磁致伸缩致动器作为主动隔振元件，并采用最优控制理论设计其主动控制器。研究了在不同的性能指标加权阵的情况下，该主动振动控制系统对基础干扰和由微制造设备产生的直接干扰所引起的微制造平台振动的控制效果。研究表明性能指标加权阵对振动控制效果影响非常大。通过大量的仿真实验确定了一组性能指标加权阵，使所设计的主动控制系统能在较宽的频率范围对基础干扰和直接干扰所引起的微制造平台振动进行有效的控制。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

DSP--数字化时代的基因芯片

DSP是当今发展最为迅速的和最有发展前景的技术之一。与普通CPU和MCU相比 ,DSP在数字信号处理方面有着无可比拟的优势 ,特别适合网络、通信、控制等需要进行大量数字信号处理的应用场合。今天DSP已经成为通信、计算机、网络、工业控制以及家用电器等电子产品中不可或缺的基础器件 ,DSP在通信、计算机、网络、工业控制以及消费类电子产品等领域有着非常广泛的应用 ,本文阐述了DSP的特点、应用和市场以及DSP技术的发展前景。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry