Emergency response to the nuclear accident at the Fukushima Daiichi Nuclear Power Plants using mobile rescue robots

On March 11, 2011, a massive earthquake (magnitude 9.0) and accompanying tsunami hit the Tohoku region of eastern Japan. Since then, the Fukushima Daiichi Nuclear Power Plants have been facing a crisis due to the loss of all power that resulted from the meltdown accidents. Three buildings housing nuclear reactors were seriously damaged from hydrogen explosions, and, in one building, the nuclear reactions became out of control. It was too dangerous for humans to enter the buildings to inspect the damage because radioactive materials were also being released. In response to this crisis, it was decided that mobile rescue robots would be used to carry out surveillance missions. The mobile rescue robots needed could not be delivered to the Tokyo Electric Power Company (TEPCO) until various technical issues were resolved. Those issues involved hardware reliability, communication functions, and the ability of the robots' electronic components to withstand radiation. Additional sensors and functionality that would enable the robots to respond effectively to the crisis were also needed. Available robots were therefore retrofitted for the disaster reponse missions. First, the radiation tolerance of the electronic componenets was checked by means of gamma ray irradiation tests, which were conducted using the facilities of the Japan Atomic Energy Agency (JAEA). The commercial electronic devices used in the original robot systems operated long enough (more than 100 h at a 10% safety margin) in the assumed environment (100 mGy/h). Next, the usability of wireless communication in the target environment was assessed. Such tests were not possible in the target environment itself, so they were performed at the Hamaoka Daiichi Nuclear Power Plants, which are similar to the target environment. As previously predicted, the test results indicated that robust wireless communication would not be possible in the reactor buildings. It was therefore determined that a wired communication device would need to be installed. After TEPCO's official urgent mission proposal was received, the team mounted additional devices to facilitate the installation of a water gauge in the basement of the reactor buildings to determine flooding levels. While these preparations were taking place, prospective robot operators from TEPCO trained in a laboratory environment. Finally, one of the robots was delivered to the Fukushima Daiichi Nuclear Power Plants on June 20, 2011, where it performed a number of important missions inside the buildings. In this paper, the requirements for the exploration mission in the Fukushima Daiichi Nuclear Power Plants are presented, the implementation is discussed, and the results of the mission are reported.     

Micromachining of electroformed nickel mold using thick photoresist microstructure for imprint technology

In order to fabricate polymer-based microstructures with feature sizes on the order of micrometers, we have been developing a microimprint technology with a fine nickel (Ni) mold instead of a conventional photolithography technique. The Ni mold was successfully fabricated by electroforming using a positive thick photoresist microstructure patterned on a silicon substrate as a replication master. The photoresist microstructure with excellent edge quality can be obtained under irradiation with single wavelength (g line) selected from a high-pressure mercury lamp. In addition, its sidewall angle in the range of 65° to 84° can be controlled precisely by varying the distance between a photomask and a photoresist surface. On the structured photoresist master, Ni was electroplated up to a thickness of about 110 μm, and then removed from the master. In this process, two-step electroplating at different current densities was carried out in order to prevent deformation of the photoresist master due to stress generated in a Ni electrodeposit. With the Ni mold, fine patterns with a width of 10 or 30 μm and a depth of 24 μm were almost completely transferred to polymetric materials (PMMA). The geometrical dimensions of the fabricated PMMA microstructures were found to be only about 10% reduction against the Ni mold.     

Thermodynamics of calcium and oxygen in molten titanium and titanium-aluminum alloy

The deoxidation equilibrium of molten titanium and titanium-aluminum alloys saturated with solid CaO has been measured in the temperature range from 1823 to 2023 K. The equilibrium constant of reaction CaO (s)=Ca (mass pct in Ti,Ti-Al)+O (mass pct in Ti,Ti-Al) and the interaction parameter between calcium and oxygen were determined for Ti, TiAl, and TiAl₃. The standard Gibbs energy of reaction for TiAl was obtained as follows: $$\Delta G^\circ = 279,000 - 103TJ/mol$$ The possibilities for the deoxidation of titanium and titanium-aluminum alloys by using calcium-based fluxes are discussed.     

A control method with pheromone information for a transport system

Since the control methods of a transport system between processing machines are specialized for each layout of the system, it is difficult to design prompt schedules and control logic for new complicated systems, especially in cases of machine faults or restructuring the system to modify the layout. In this article, we describe a multiagent transport control system which utilizes pheromone information. Each element of the system acts as an agent and estimates the appropriate path and time to drive out the products using information obtained by communication with other elements as well as pheromone information deposited on the tracks of the products.     

Fine two-phase routing over shortest paths with traffic matrix

This paper presents an IP finely-distributed load-balanced routing scheme based on two-phase routing over shortest paths, where the traffic matrix is given. It is called the fine two-phase routing (F-TPR) scheme. F-TPR more finely distributes traffic from a source node to intermediate nodes than the original TPR. F-TPR determines the distribution ratios to intermediate nodes for each source–destination node pair independently. To determine an optimum set of distribution ratios, a linear programming (LP) formulation is derived. We compare the F-TPR scheme against the TPR scheme and the sophisticated traffic engineering (TE) scheme of Multi-Protocol Label Switching (MPLS-TE). Numerical results show that F-TPR greatly reduces the network congestion ratio compared to TPR. In addition, F-TPR provides almost the same network congestion ratios as MPLS-TE, the difference is surprisingly less than 0.1% for the various network topologies examined. In addition, considering the practical implementation of F-TPR for routers, we also investigate the case that traffic from a source node to a destination node is not allowed to be split over multiple routes. The non-split problem is formulated as an integer linear programming (ILP) problem. As it is difficult to solve the ILP problem within practical time, two heuristic algorithms are presented: Largest Traffic Demand First (LTDF) and a Random Selection (RS). The applicability of LTDF and RS are presented in terms of network size. We find that non-split F-TPR also matches the routing performance of MPLS-TE within an error of 1%, when network size is large enough.     

Navigation system for an autonomous robot using an ocellus camera in an indoor environment

Autonomous and mobile robots are being expected to provide various services in human living environments. However, many problems remain to be solved in the development of autonomous robots that can work like humans. When a robot moves, it is important that it be able to have self-localization abilities and recognize obstacles. For a human, the present location can be correctly checked through a comparison between memorized information assuming, it is correct, and the present situation. In addition, the distance to an object and the perception of its size can be estimated by a sense of distance based on memory or experience. Therefore, the environment for robotic activity assumed in this study was a finite-space such as a family room, an office, or a hospital room. Because an accurate estimation of position is important to the success of a robot, we have developed a navigation system with self-localization ability which uses only a CCD camera that can detect whether the robot is moving accurately in a room or corridor. This article describes how this system has been implemented and tested with our developed robot.     

Detection of environmental changes from network structure

We studied the networks of the temperature record in the atmosphere. They are made by the strength of the synchronization, including the delay between temperatures at locations on Earth. We consider these locations as nodes, and we consider a pair of locations as a link if the synchronization between them is stronger than a threshold. The network is scale-free, which is thought to contribute to the stability of the climate. This work was presented in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

A counterexample to a proposed dynamic programming algorithm for optimal bid construction in an auction-based fully distributed manufacturing system

The paper by Veeramani and Wang (Int J Adv Manuf Technol 28:541–550, 2006) published in this journal offers a general bid construction scheme for minimizing the job flow time in auction-based manufacturing control and claims the optimality of the procedure. The purpose of this note is to provide a small example, in which their proposed new method fails to produce an optimal solution. We also address efficient correct algorithms so as to protect the readers from mistakenly believing that their new procedure is a better way of computing solutions.     

感应电机无速度传感器矢量控制系统的定子电阻在线辨识

该文针对利用磁通观测器推算转子磁通的感应电机无速度传感器矢量控制系统，提出了定子电阻在线辨识法。在利用q轴磁通推算转速的基础上，该系统利用d轴磁通误差实现定子电阻在线辨识，该方案的优点是系统简单，解决了低速运行时电压模型的定子电阻变化对系统稳定性和速度控制精度的影响问题。数字仿真和实验结果验证了定子电阻在线辨识的必要性和该方案的有效性。     

Impact of Multimedia Traffic Characteristics on ATM Network Configuration

This paper proposes a new topological designmethod, named BXCQ, which optimizes logical networkconfiguration while guaranteeing Quality-of-Service(QoS) requirements for each service class in an ATMnetwork. The BXCQ method determines the optimum logicalnetwork topology associated with each service class soas to minimize network cost. In our previously proposedFull-Net architecture these different logical topologies can be suitably mapped at the sametime on the same ATM physical network by using theVirtual Channel Handler (VCH) to create differentlogical interconnection networks. The BXCQ method allows us to clarify the relations between multimediatraffic characteristics and desirable logical networkconfigurations in Full-Net. Evaluation results suggestthat a service class that is bursty, delay tolerant, and cell loss sensitive with small demandshould be supported by a loop-like topology. This studywill be useful for designing flexible and cost-effectivemultimedia networks that can also adapt to not-yet-known services.