Numerical analysis of wave-type heat transfer propagating in a thin foil irradiated by short-pulsed laser

This paper presents a numerical simulation of wave-type heat transfer phenomena propagating in an aluminum thin foil irradiated by a pulsed laser using the cubic interpolated propagation method coupled with a thermo-convective model. We did not use the two-step model and dual-phase lag model, which are generally known as the non-Fourier heat conduction law, but wave-type heat transfer phenomena could be observed by our method. The main characteristic of the method is to solve the governing equation including the equation of continuity, the equation of motion, the equation of energy and the equation of state. It is found that when the pulse duration is under the order of picosecond, the pure heat conduction is hardly observed and heat transfer toward the inside of materials occurs only by a thermal shock wave. The heat conduction mode after pulse laser irradiation is strongly dependent upon the value of total incident laser energy density E_in and the threshold value for pure heat conduction is 5.0 × 10⁴ J/m² for an aluminum.     

Catalytic decomposition of biomass tars with iron oxide catalysts

Catalytic gasification of wood (Cedar) biomass was carried out using a specially designed flow-type double beds micro reactor in a two step process: temperature programmed non-catalytic steam gasification of biomass was performed in the first (top) bed at 200–850 °C followed by catalytic decomposition gasification of volatile matters (including tars) in the second (bottom) bed at a constant temperature, mainly 600 °C. Iron oxide catalysts, which transformed to Fe₃O₄ after use possessed catalytic activity in biomass tar decomposition. Above 90% of the volatile matters was gasified by the use of iron oxide catalyst (prepared from FeCl₃ and NH_3aq) at SV of 4.5 × 10³ h^?1. Tar was decomposed over the iron oxide catalysts followed by water gas shift reaction. Surface area of the iron oxide seemed to be an important factor for the catalytic tar decomposition. The activity of the iron oxide catalysts for tar decomposition seemed stable with cyclic use but the activity of the catalysts for the water gas shift reaction decreased with repeated use.     

Diamond nanoseeding on silicon: Stability under H2 MPCVD exposures and early stages of growth

Detonation nanodiamond dispersed on silicon surfaces underwent different H₂ MPCVD exposures. The induced changes at the surface have been characterized in situ by XPS and XEELS. Then, a short CH₄/H₂ growth step was applied. This sequential study revealed an excellent stability of detonation nanodiamond. The sp³ etching rate is insufficient to remove nanodiamond even under intense H₂ plasma. The H₂ exposure could be successfully used to remove C–C sp² carbon without altering sp³ seeds. Moreover, the formation of silicon carbide observed after the hydrogen treatment is thought to be helpful to enhance the adhesion of nanodiamond particles on the substrate.     

BaO—CaO—Na2O—CaF2—Cr2O3渣系的不锈钢脱磷

测定了１５００℃时磷在ＢａＯ－ＣａＯ－Ｎａ２Ｏ－ＣａＦ２－Ｃｒ２Ｏ３渣子和０．１２Ｃ－０．７１Ｓｉ－１８Ｃｒ不锈钢熔体之间的分配比，试验结果表明，该渣系的不锈钢脱磷能力比ＣａＯ基渣好，与ＢａＯ基渣相当。     

Thermal Transformation of Ring-Opened [2 2] C60 Dimer into a Wide-Bridged C120 Isomer. A Computational Evaluation of Fulvalene-Naphthalene Rearrangements

As a continuation of the studies on thermal transformation of the [2+2] C₆₀ dimer (1), the consequence of the pyracylene-rearrangement-like valence isomerization of the fulvalene partial structure at the bridge of the ring-opened product from 1, namely 2, was searched by dynamic reaction coordinate /AM1 semiempirical MO calculations. It is predicted that the fulvalene bridge of 2 rearranges into naphthalene partial structure by the concerted 'in-plane' mechanism to give a wide-bridged C₁₂₀ intermediate having twenty five-membered rings and two ten-membered rings (3). The computed energy of activation (145 kcal/mol) is 40 kcal/mol lower than those computed for pyracylene rearrangements. In contrast, the recently reported analogous rearrangement of indigo (13) to dibenzonaphthyridindione (14) is computed to occur by the stepwise 'sp³' mechanism.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Robust digital control of a DC–DC buck converter with low frequency samplings

A robust DC?CDC converter which can covers extensive load change and also input voltage changes with one controller is needed. Then the demand to suppress output voltage change becomes still severer. We propose an approximate 2-degree-of-freedom (2DOF) digital controller which realized start-up response and dynamic load response independently. The controller makes a control bandwidth wider, and at the same time makes variations of the output voltage small at sudden changes of a load and an input voltage. In this paper, a new approximate 2DOF digital control system with additional zeros is proposed. Using the additional zeros, the second-order differential transfer characteristics between equivalent disturbances and a output voltage are realized. Therefore, the new controller makes variations of the output voltage smaller and the sudden changes of the load and the input voltage. This controller is actually implement on a DSP and is connected to the DC?CDC converter. Experimental results demonstrate that this type of digital controller can satisfy given severe specifications with low frequency sampling.     

Crystallization process and magnetic properties of Fe100−x,B x (10 ≦ × ≦ 35) amorphous alloys and supersaturated state of boron inα-Fe

Amorphous specimens of Fe_100–x B _x were prepared in the range 10 × 35 at % B by a single-roller method. The crystallization process and the boron concentration dependence of the Curie temperature were examined by differential scanning calorimetry, X-ray diffraction, Mössbauer spectroscopy and magnetic measurements. Two-step crystallization was observed in specimens with× < 17: amorphous amorphous + boron-supersaturated b c c phase (-Fe(B)) t-Fe₃B +-Fe. A single-Fe(B) phase was not observed. The transition temperature from t-Fe₃B to stable (-Fe + t-Fe₂B) sensitively depends on the boron content in the alloys. The crystallization temperature (T _x) of the amorphous alloys was almost unchanged for 17 × 31, but increased remarkably at high boron concentrations of× 33, where the decomposition products consisted of t-Fe₂B and o-FeB. The Curie temperature (T _c) of the amorphous phase was as low as 480 K at× = 10, increased with increasing boron content up to 820 K and then decreased in the high boron concentration alloys of× > 28. A single-Fe(B) phase was not detected in the as-quenched specimens of× = 8 and 10. The phase coexisted with the o-Fe₃B and amorphous phases. The lattice parameter of the phase was 0.2861₀ nm which was smaller than that of pure iron by 2/1000, indicating the substitutional occupation of boron atoms in the b c c lattice.     

Activities of FexO in CaO + CaF2 + SiO2 + FexO quaternary slags by disposable electrochemical oxygen probes

The activities of Fe_xO in CaO + CaF₂ + SiO₂ + Fe_xO quaternary slags were measured by means of solid-oxide galvanic cell. The Fe_xO activities in the slags are influenced by CaF₂ as well as SiO₂. At constant Fe_xO mole fractions, e.g., , at low SiO₂ mole fractions i.e., , the substitution of CaF₂ for CaO has an effect of raising the Fe_xO activity. At higher SiO₂ mole fractions, e.g., , however, such an effect becomes insignificant.     

CO2气体保护的激光焊接12mm厚低碳钢板

采用CO2 作为保护气体消除大熔深激光焊接低碳钢时易发生的气孔问题 ,并对比研究了CO2 和Ar气保护条件下 12mm厚低碳钢板激光焊缝的组织和韧性。焊接试验利用 4kWNd :YAG激光器 ,采用双面深熔焊的方法 ,焊接条件为 4kW激光功率和0 .3 ,0 .5m/min的焊接速度。冲击试验采用一种自行设计的带侧面缺口的三缺口冲击试样 ,以保证断裂全部发生在焊缝。结果表明 ,利用CO2 作保护气体焊接低碳钢板 ,可以有效消除大熔深激光焊接时的气孔问题 ,并获得比Ar气保护下硬度较低 ,冲击韧性高的焊缝。研究工作为解决大功率激光深熔焊时容易发生的气孔问题提供了一条有效途径