X70配套埋弧焊丝用H08D盘条的研制

介绍了北营公司X70配套埋弧焊丝用H08D盘条的开发研制情况.其生产工艺的关键点为:转炉采用“双渣法除磷”,脱氧合金化在转炉和LF炉两个阶段完成,连铸采用结晶器电磁搅拌及末端电磁搅拌、恒定拉速;盘条采用控冷控轧及轧后延迟型斯太尔摩冷却工艺等措施.生产的成品盘条成分、力学性能、金相组织等指标均满足客户拉拔工艺要求.     

上榆泉煤矿煤泥水多参数在线检测系统应用研究

针对上榆泉煤矿煤泥水性质参数人工检测周期长、误差大、滞后性严重的问题,采用多参数传感器和PLC,开发了煤泥水多参数在线检测系统。经过8 h稳定运行,平均结果显示该厂煤泥水参数为pH值为7.71、浓度9.45%、中值直径(D50)39.56μm、流量2 440 m3/h、水质硬度428.94 mg/L,与人工检测结果相一致。应用结果表明,该检测系统能够实现煤泥水多参数在线监测和数据分析功能,使煤泥水的处理更高效。     

铸态Ti-20Zr-20Al钛合金动态压缩力学性能与断裂机制研究

采用X射线衍射仪、金相显微镜、分离式霍普金森杆和扫描电镜等手段研究了Ti-20Zr-20Al钛合金在动态压缩条件下的微观结构、力学性能和断裂机制。结果表明,Ti-20Zr-20Al铸态合金由Zr基体相和TiAl/Ti₃Al针状相组成; 随着应变率增加,合金的抗压强度增加,失效应变显著增加; Ti-20Zr-20Al合金的断裂机制为解理断裂; 随着应变率增加,试验压缩断裂后碎片总数增大,平均粒径减小。采用DID模型模拟的材料碎片尺度与实验结果比较吻合,Grady模型与实验结果的偏差较大。     

The effect of optimized carbon source on the synthesis and composition of exopolysaccharides produced by Lactobacillus paracasei

This study aimed to predict the optimal carbon source for higher production of exopolysaccharides (EPS) by Lactobacillus paracasei TD 062, and to evaluate the effect of this carbon source on the production and monosaccharide composition of EPS. We evaluated the EPS production capacity of 20 strains of L. paracasei under the same conditions. We further investigated L. paracasei TD 062, which showed the highest EPS-producing activity (0.609 g/L), by examining the associated biosynthesis pathways for EPS. Genomics revealed that fructose, mannose, trehalose, glucose, galactose, and lactose were carbon sources that L. paracasei TD 062 could use to produce EPS. We identified an EPS synthesis gene cluster that could participate in transport, export, and sugar chain synthesis, and generate 6 sugar nucleotides. Experimental results showed that the sugar content of the EPS produced using fermentation with the optimized carbon source (fructose, mannose, trehalose, glucose, galactose, and lactose) increased by 115%. Furthermore, use of the optimized carbon source changed the monosaccharide content of the associated EPS. The results of enzyme activity measurements showed significant increases in the activity of 2 key enzymes involved in the glycoside synthesis pathway. Our study revealed that optimizing the carbon source provided for fermentation not only increased the production of EPS, but also affected the composition of the monosaccharides by increasing enzyme activity in the underlying synthesis pathways, suggesting an important role for carbon source in the production of EPS by L. paracasei TD 062.     

Role of Co in formation of Ni-Ti clusters in maraging stainless steel

The effect of Co addition on the formation of Ni-Ti clusters in maraging stainless steel was studied by three dimensional atom probe (3DAP) and first-principles calculation. The cluster analysis based on the maximum separation approach showed an increase in size but a decrease in density of Ni-Ti clusters with increasing the Co content. The first-principles calculation indicated weaker Co-Ni (Co-Ti) interactions than Co-Ti (Fe-Ti) interactions, which should be the essential reason for the change of distribution characteristics of Ni-Ti clusters in bcc Fe caused by Co addition.     

不同制样方法对直流辉光放电质谱法测定氮化硼中27种杂质元素的影响

讨论了3种制样方法对直流辉光放电质谱法(dc-GDMS)检测氮化硼中的Na、Mg、Al、Si等27种杂质元素的影响。3种制样方法分别如下所示:方法1,直接把氮化硼压在铟薄片上;方法2,把氮化硼压在铟薄片上后,再盖上一层铟罩;方法3,把压碎后的氮化硼放在针状钽勺上。在优化的辉光放电参数下对比了3种不同制样方法对基体信号强度的影响。试验表明:在方法1中,当氮化硼尺寸约为3mm×3mm,厚度小于1mm时,基体¹¹B的信号可达1.8×10⁷ cps;在方法2中,选择铟孔大小合适的铟罩,基体¹¹B的信号可达1.0×10⁷ cps;方法3获得基体信号强度比方法1、方法2高一个数量级。大部分元素在中分辨率下可获得较好的结果,而对于在高分辨率下也较难分离的元素,可选择丰度较低的同位素在中分辨率下进行测定,如Ge选择⁷⁰Ge⁺,Se选择⁸²Se⁺,Cd选择¹¹¹Cd⁺,Sn选择¹¹⁹Sn⁺,Ag选择¹⁰⁹Ag⁺,Pt选择¹⁹⁴Pt⁺。氮化硼中的杂质元素含量可通过样品片中待测元素含量减去来自于铟薄片或钽勺中该元素贡献的含量来计算获得。将样品平行测定5次,相对标准偏差均在20%以内。对于Al、Si、Ti等元素的测定,3种制样方法的测定结果基本一致;方法1、方法2中检测到的In含量较大,使得铟中的Ni、Cu对氮化硼的测定值影响较大;方法3由于钽中Fe、Cu的贡献导致氮化硼中Fe、Cu的检测值较大,但方法3获得的基体信号强度大,可降低部分元素的检出限,如Cr、Mn、Ga、Ge等。综上所述,方法3为优选方法。     

Surface structural and solar absorptance features of nitrate-based copper-cobalt oxides composite coatings: Experimental studies and molecular dynamic simulation

The copper and cobalt oxides composites coatings on aluminum substrates have been successfully synthesized via sol-gel method using nitrate-based sol precursors. The composites were characterized by X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscopy (FESEM), Atomic Force Microscopy (AFM), and UV–Vis–NIR spectrophotometry. The sol-gel reactions were discussed and Molecular Dynamics (MD) simulation was integrated into the study to predict molecules assembly properties. The XRD analyses revealed that the CuO and the Co₃O₄ composites were formed after the annealing process with the average difference of the calculated lattice parameters compared to ICDDs was 1.17%. The surface electronic structure was mainly consisted of tetrahedral Cu(I), octahedral Cu(II), tetrahedral Co(II), octahedral Co(III) as well as surface, sub-surface and lattice oxygen O^?. The XRD, XPS and MD simulation results showed that there was minimal (or possibly non-existing) indication of copper-cobalt mixed phase oxides formations. FESEM and AFM surveys revealed that the coating had a porous surface composed of interlinked nanoparticles in the range of ~?10 to ~?40?nm. UV–Vis–NIR reflectance spectra showed that the sol precursors concentration and the dip-drying cycle significantly influenced the absorptance value with optimum absorptance (α) of 88.7% exhibited by coating synthesized using sol concentration of 0.1?M and 10 dip-drying cycles. High absorptance value and simplicity in the synthesis process render the coatings to be very promising candidates for solar selective absorber (SSA) applications.