Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

InGaN microring light-emitting diodes

The fabrication and performance of an InGaN light-emitting diode (LED) array based on a microring device geometry is reported. This design has been adopted in order to increase the surface area for light extraction and to minimize losses due to internal reflections and reabsorption. Electrical characteristics of these devices are similar to those of a conventional large-area LED, while the directed light extraction proves to be superior. In fact, these devices are found to be more efficient when operated at higher currents. This may be attributed to improved heat sinking due to the large surface area to volume ratio. The potential applications of these devices are also discussed.     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.     

Wireless-adaptive fair scheduling for multimedia stream

As packet cellular networks are expected to support multimedia services, the authors incorporate the multimedia QoS requirements into the design of a new scheduling algorithm. The proposed wireless-adaptive fair scheduling tries to allocate time slots for each user with fair share by considering the varying channel condition while reflecting the stream requirements and achieving high throughput.     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

Model-based monitoring of diamond turning process using cross entropy

This paper discusses the model-based monitoring as one of key steps toward building an inprocess diagnostic tool for the supervisory level control in diamond turning. In particular, estimation of surface profile from a nonlinear force model and model-based monitoring of tool chipping are demonstrated. Classification rule is based on the minimization of information-theoretic measure called the cross entropy. The experimental results indicate that monitoring strategy based on the minimum cross entropy guarantees the consistent and optimum classification results in the presence of varying cutting conditions. In addition, the cross entropy as a criterion for indicating the dynamic quality of machine-tool is explained.     

The effect of topical corticosteroids on refractive outcome and corneal haze after photorefractive keratectomy

BACKGROUND: The effect of topical corticosteroids after excimer laser photorefractive keratectomy (PRK) remains a matter of some controversy. Refractive effects may be different according to the amount of myopia and timing of instillation. METHODS: Two groups of patients were studied: Study A consisted of 215 eyes (128 patients) with PRK (mean baseline myopia, -6.53 +/- 2.22 D) that received no corticosteroids (No Corticosteroid Group) unless significant regression or corneal haze appeared (Delayed Corticosteroid Group), and in Study B, we randomly assigned eyes to the Initial Corticosteroid Group (mean baseline myopia, -6.39 +/- 1.84 D) or the No/delayed Corticosteroid Group (mean baseline myopia -5.78 +/- 2.02 D). Clinical results after PRK for low-to-moderate and high myopia were compared. RESULTS: In the first group, 70.9% (73 eyes) of moderately myopic eyes (mean, -4.56 +/- 1.10 D) belonged to the No Corticosteroid Group that had a mean refraction of -5.39 +/- 1.77 D. Delayed Corticosteroid Group eyes were more myopic (mean, -7.52 +/- 2.10 D), and showed more severe haze than those in the No Corticosteroid Group. In study B, only in high myopes with more than -6.00 D (mean, -7.76 +/- 1.15 D) did refraction and corneal haze outcomes show significant difference between the Initial Corticosteroid Group and the No/delayed Corticosteroid Group. CONCLUSIONS: The effects of topical corticosteroids after PRK were less in moderate myopes compared to high myopes. Delayed instillation of corticosteroids did not reverse the regression or haze whereas initial instillation showed a beneficial effect on high myopes but not on moderate myopes.     

Arthroscopic reduction and fixation of bony avulsion of the posterior cruciate ligament of the tibia

Bony avulsion fractures of the posterior cruciate ligament of the tibia have commonly been treated by open reduction and internal fixation using the posterior approach. However, this approach, using the prone position, makes it difficult to investigate and treat other combined injuries of the knee joint. We report a case of posterior cruciate ligament avulsion of the tibia that was arthroscopically reduced and firmly fixed with two cannulated screws. The posterior sag was absent after the operation and the result was excellent. By arthroscopy, we got rigid fixation of the avulsed fragment for early rehabilitation, and detection of a concomitant injury was also possible.